Toshiba 65/5560 Anleitung zur Verwendung

SERVICE HANDBOOK

PLAIN PAPER COPIER

65/5560

Click the Page Only button to close the overview area of the window.

Click the Bookmarks and Page button to open the Contents and

display bookmarks created for the document. Click a bookmark’s name

to go to the Page marked by that bookmark.

Click the Thumbnails and Page button to open the overview area and

display thumbnail images of each document page. Click a thumbnail to

go to the page marked by that thumbnail.

65/5560 PRECAUTIONS 1MAY.1997 © TOSHIBA CORP.

GENERAL PRECAUTIONS REGARDING THE INSTALLATION AND

THE SERVICE OF THE 6560

1. Transportation/Installation

•When transporting the copier, move it by the casters while lifting the stoppers.

The copier is quite heavy and weighs approximately 230 kg (507 lb); therefore, pay full attention

when handling it.

2. Installation

•Be sure to use a dedicated outlet with AC 115V/15A (220V, 230V, 240V/10A) or more for the

power source.

•The copier must be grounded for safety.

Never ground it to a gas pipe or a water pipe.

•Select a suitable place for installation.

Avoid excessive heat, high humidity, dust, vibration and direct sunlight.

Also provide proper ventilation as the copier emits a slight amount of ozone.

•To insure adequate working space for copying operations, keep a minimum clearance of 80 cm

(32") on the left, 80 cm (32") on the right and 10 cm (4") in the rear.

3. Service of Machines

•Basically, be sure to turn the main switch off and unplug the power cord during service.

•Be sure not to touch high temperature sections such as the exposure lamp, the fuser unit, the

damp heater and their periphery.

•Be sure not to touch high-voltages sections such as the chargers and the high-voltage transformer.

•Be sure not to touch rotating/operating sections such as gears, belts, pulleys,etc.

•When servicing the machines with the main switch turned on, be sure not to touch live sections

such as the lamp terminal etc.

•Use suitable measuring instruments and tools.

65/5560 PRECAUTIONSMAY.1997 © TOSHIBA CORP. 2

4. Main Service Parts for Safety

•The thermofuse,thermistor,fuse,breaker and door switches,thermostat etc. are particularly important

for safety.Be sure to handle/install them properly.

5. Notice Labels

•Be sure to check the rating plate and the notice labels such as "Unplug the power cord during

service" ,"Hot area" ,etc. to see if there is any dirt on their surface or if they are properly stuck to

the copier during servicing.

6. Disposition of Consumable Parts/Packing Materials

•Regarding the recovery and disposal of the copier, supplies, consumable parts and packing

materials, it is recommended to follow the relevant local regulations or rules.

7. When parts are disassembled, reassembly is basically the reverse of disassembly unless otherwise

noted in this manual or other related documents. Be careful not to reassemble small parts such as

screws, washers, pins, E-rings, toothed washers in the wrong places.

8. Basically, the machine should not be operated with any parts removed or disassembled.

9. Precautions Against Static Electricity

•The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband,

because the ICs on it may be damaged due to static electricity.

65/5560 SPECIFICATIONS 1-1 MAY.1997 © TOSHIBA CORP

1. SPECIFICATIONS, ACCESSORIES AND OPTIONS

1.1 Specifications

1.2 Accessories

1.3 Options

1.4 System List

COSMOS

SkipOK Cancel

Texts from 1-1 to 1-5 in the

6560 Service Handbook

are the same as texts from 1-1 to 1-5 in the

6560

Service Manual

Do you refer to the

6560 Service Manual

65/5560 ADJUSTMENT MAY.1997 © TOSHIBA CORP.2-1

2. ADJUSTMENT

2.1 TOSHIBA Supplies List

COSMOS

SkipOK Cancel

Text 2-1 in the

65/5560 Service Handbook

is same as

text 20-2 in the

65/5560 Service Manual

Do you refer to the

65/5560 Service Manual

65/5560 ADJUSTMENTMAY.1997 © TOSHIBA CORP. 2-2

2.2 List of Adjustment Jigs Used

COSMOS

SkipOK Cancel

Text 2-2 in the

65/5560 Service Handbook

is same as

text 20-1in the

65/5560 Service Manual

Do you refer to the

65/5560 Service Manual

65/5560 ADJUSTMENT MAY.1997 © TOSHIBA CORP.2-3

When either the CLEAR PAPER( )or CALL SERVICE( ) symbol appears,press the CLEAR/

STOP and "8"keys simuitaneously and the corresponding error code will be displayed.To clear the

error code,turn off the power.

Code Machine status

E1 Paper jam inside thr copier

E2 Paper jam near fuser unit

E3 Paper remaining inside the copier when the main switch is turned on

E4 The front cover is opened during copying

E5 Paper misfeed in LCF and manual feeding and paper jam in front of the aligning roller

E8 Paper misfeed (ADD)

E9 Paper misfeed (pedestal)

EC Paper misfeed (ADF)

ED Paper misfeed in ADF transport unit

EE Paper misfeed in ADF exit/reverse unit

C3 Abnormal serial transmission between main CPU and sub-CPU

C5 The optical system will not initialise;the optical system is locked

C7 Heat roller thermistor is open-circuited,

CB ADF feed motor locked

CC ADF transport motor locked

A0 Abnormal signal transmission in PFC interface

A1 Faulty charger wire cleaning operation

A2 ADD malfunction

A3 PFC (paper feed controller) malfunction

A4 Sorter malfunction

A5 Abnormal signal transmission between main CPU and IPC

A6 Abnormal signal transmission in sorter interface

A7 Abnormal signal transmission in ADF interface

A9 Blown exposure lamp or defective AES

2.3 Error Codes

65/5560 ADJUSTMENTMAY.1997 © TOSHIBA CORP. 2-4

2.4 DIP Switch/Jumper/VR Functions

(1) Logic PC board

JP1

PWA-F-LGC-154/155

Jumper Name When shipped Remarks

JP1 UNT No jumper Jumper:Factory adjustment mode

(open) No jumper:Normal mode

Note: Replacement PC boards are supplied with the jumper

installed.

Be sure to cut it when replacing the PC boards.

(2) Paper feed control PC board

PWA-F-PFC-154/155

JP3

(TP-SG)

VR2

VR1

R61

R60

VR FUNCTION

VR2 For adjustment ofthe paper width guide position of the

stack guide unit.

Note: Adjustoment procedure

Plus terminal of the tester Minus COM terminal of the tester Adjustment value VR

Aroow side of R60 JP3(TP-SG) 0~0.1V VR2

PWA-F-PFD-152

(TP-SG)

JP25

R39

VR2

R19

VR1

VR3

R40

(3) Paper feed drive PC board

VR Function

VR1 For adjustment of the PFP lower aligning value.

VR2 For adjustment of the PFP middle aligning value.

VR3 For adjustment of the PFP upper aligning value.

Note: Adjustment procedure

Plus teminal of the tester Minus COM terminal Adjustment value VR

of the tester

Arrow side of R19 JP25(TP-SG) 0~0.1V VR1

Arrow side of R39 JP25(TP-SG) 0~0.1V VR2

Arrow side of R40 JP25(TP-SG) 0~0.1V VR3

ëëë

65/5560 ADJUSTMENT MAY.1997 © TOSHIBA CORP.2-5

(4) ADF logic PC board

1 2 3 4 5

PWA-F-LGC-758

Note: The independent operation mode is performed as in the following procedure;set the DIP switch 1

to its ON position and turn on the power.Select the menu of the independent operation mode and

then open and close the jam release cover or the ADF cover.

↑

At power on

Duning independent operation mode

ON OFF ON OFF

1 Independent Normal mode Feeding mode Drive system

operation check mode

mode

2 Original set Original set Duplex Single-sided

by switchback by direct feeding mode feeding mode

stopping

3 USA/Canada Europe Aging mode Multifeeding

version version without paper mode

4 E2PROM Normal mode Not used Not used

initialigation

5 Not used Normal mode 2 in 1 mode OFF

DIP switch

65/5560 ADJUSTMENTMAY.1997 © TOSHIBA CORP. 2-6

2.5 Self-Diagnosis Modes

Mode Input Definition Cleaning Display after selection

Code method

All-LEDs-lit "01" All LEDs on the control panel are lit. C/S

Aging mode "02" Aging (ADF does not operate) "09" AGING 100% 0

Test mode "03" Motor test and input/output check "09" TEST MODE C 100% C

Test mode "04" Motor test and input/output check "09" TEST MODE C 100% C

Adjustment "05" Adjustment of items "09" TEST MODE A 100% A

mode

Forced ready "06" Forced entry of ready mode

mode

Aging mode "07" Aging (includes ADF) "09" AGING 100% 0

Setting mode "08" System switchover and setting of each "09" TEST MODE D 100% D

priority mode,PM counter,etc.

Note: To access the desired diagnostic mode,turn on the power switch while pressing the appropriate

keys.

•All-LEDs-lit mode(01):

0 1 / PWR All LEDs light C/S Exit

•Aging mode(02 or 07):

0 2 / PWR Aging C/S Exit

( 0 7 ) PRINT

•Test mode(03 or 04)

For these test modes,refer to 2.5.1 and 2.5.2.

•Adjustment mode(05):

For this mode,refer to"2.5.3 Adjustment Mode".

•Forced ready mode(06):

PWR 0 6 Forced ready

Note:This mode is for checking the paper feeding operation only.

•Setting mode(08):

For this mode,refer to"2.5.4 Setting mode".

Note: C/S : Press the CLEAR/STOP key

PWR: Turn on the power switch

INT : Press the INTERRUPT key

E/S : Press the ENERGY SAVER key

0 9

→→→

→

→→

→

→→

←

↑

Inhaltsverzeichnis

Andere Toshiba Kopierer Handbücher

Toshiba

Toshiba e-studio 45 Bedienungsanleitung

Toshiba

Toshiba e-studio 12 Bedienungsanleitung

Toshiba

Toshiba SmartLink e-STUDIO25 Bedienungsanleitung

Toshiba

Toshiba e-studio 210c Bedienungsanleitung

Toshiba

Toshiba e-studio 120 Bedienungsanleitung

Toshiba

Toshiba e-Studio 223CS Installationsanleitung

Toshiba

Toshiba e-STUDIO 550 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 4511 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO 550 Bedienungsanleitung

Toshiba

Toshiba e-studio 16 Bedienungsanleitung

Toshiba

Toshiba DP1600 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO206L Bedienungsanleitung

Toshiba

Toshiba 2550 Bedienungsanleitung

Toshiba

Toshiba 1550 Bedienungsanleitung

Toshiba

Toshiba 3560 Anleitung zur Verwendung

Toshiba

Toshiba MR-2017 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO45 Bedienungsanleitung

Toshiba

Toshiba 1550 Anleitung zur Verwendung

Toshiba

Toshiba e-studio 120 Bedienungsanleitung

Toshiba

Toshiba e-studio 353 Bedienungsanleitung

Toshiba

Toshiba 5560 Bedienungsanleitung

Toshiba

Toshiba e-studio 12 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO GL-1020 Handbuch

Toshiba

Toshiba 3560 Bedienungsanleitung

Beliebte Kopierer Handbücher anderer Marken

Canon

Canon iR1210 Referenzhandbuch

Ricoh

Ricoh FW740 Bedienungsanleitung

Minolta

Minolta CF910 Bedienungsanleitung

Ricoh

Ricoh B003 Bedienungsanleitung

Xerox

Xerox EC70 Bedienungsanleitung

Oce

Oce 9800 Bedienungsanleitung

Olivetti

Olivetti d-Copia 1800 Bedienungsanleitung

Minolta

Minolta Di181 Bedienungsanleitung

Canon

Canon iR5000i Bedienungsanleitung

Telecrane

Telecrane F25 Bedienungsanleitung

Xerox

Xerox WorkCentre Pro 40 Bedienungsanleitung

Canon

Canon NP6317 Anleitung zur Verwendung

Sharp

Sharp AR-5015 N Bedienungsanleitung

Ricoh

Ricoh Di-C1 Bedienungsanleitung

Mita

Mita MIP-2400 Handbuch

Sharp

Sharp AL-2061 Bedienungsanleitung

Muratec

Muratec MFX-C2280 Bedienungsanleitung

Ricoh

Ricoh FT5034C Bedienungsanleitung