Toshiba RD-XV47KE Bedienungsanleitung

SERVICE MANUAL

TOSHIBA CORPORATION 2007

VCR

REC

PROGRAM

DUBBING

VCR

HDD

DVD

HDD

DVD

REC

HDD/DVD

ON / STANDBY

The above models are classified as green products (*1), as indicated by the underlined serial

numbers. This Service Manual describes replacement parts for the green products. When

repairing these green product(s), use the part(s) described in this manual and lead-free solder (*2).

For (*1) and (*2), see the next page.

FILE NO. 810-200719GR

HDD &DVD

/Video Cassette Recorder

RD-XV47KE

RD-XV47KB

RD-XV47KF

Published in Japan, July 2007 GREEN

SECAMPAL

PA L

VCR

REC

PROGRAM

DUBBING

VCR

HDD

DVD

HDD

DVD

REC

HDD/DVD

ON / STANDBY

REVISED: 01

(*1) GREEN PRODUCT PROCUREMENT

The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling

and reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use of

certain Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any

marketing of new products containing the restricted substances.

Increasing attention is given to issues related to the global environmental. Toshiba Corporation

recognizes environmental protection as a key management tasks, and is doing its utmost to

enhance and improve the quality and scope of its environmental activities. In line with this,

Toshiba proactively promotes Green Procurement, and seeks to purchase and use products,

parts and materials that have low environmental impacts.

Green procurement of parts is not only confined to manufacture. The same green parts used in

manufacture must also be used as replacement parts.

(*2) LEAD-FREE SOLDER

This product is manufactured using lead-free solder as a part of a movement within the consumer

products industry at large to be environmentally responsible. Lead-free solder must be used in the

servicing and repair of this product.

WARNING

This product is manufactured using lead free solder.

DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT !

The melting temperature of lead-free solder is higher than that of leaded solder by 86°F to 104°F

(30°C to 40°C). Use of a soldering iron designed for lead-based solders to repair product made

with lead-free solder may result in damage to the component and or BOARD being soldered.

Great care should be made to ensure high-quality soldering when servicing this product —

especially when soldering large components, through-hole pins, and on BOARDs — as the level

of heat required to melt lead-free solder is high.

MAIN SECTION

HDD & DVD

/ Video Cassette Recorder

RD-XV47KE/RD-XV47KB/RD-XV47KF

TABLE OF CONTENTS

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1

Laser Beam Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1

Important Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1

Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1

Handling Precautions for HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5-1

Preparation for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1

Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1

Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8-1

How to Self-Check and Initialize the HDD & DVD/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1

Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10-1

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1

Function Indicator Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1

Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1

Schematic Diagrams / BOARD’s and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1

Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1

IC Pin Function Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17-1

Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18-1

Exploded Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19-1

Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20-1

Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21-1

Main Section

ISpecifications

IPreparation for Servicing

IAdjustment Procedures

ISchematic Diagrams

IBOARD’s

IExploded Views

IParts List

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

1-1-1 E3B90SP

SPECIFICATIONS

Note

• The specifications and design of this unit are subject to change without notice.

General

System HDD, DVD-Video, DVD-RW / R, DVD+RW / R, VCD, CD-DA,

CD-RW / R, Video Cassette Tape

VCR video heads Four heads

HDD Internal 3.5 inch HDD 160 GB

Power requirements 220–240 V ± 10%, 50 Hz ± 0.5%

Power consumption 60 W (standby: 8.0 W)

Weight 5.

5.9 kg (RD-XV47KB)

8 kg (RD-XV47KE/RD-XV47KF)

Dimensions (width x height x depth) 435 x 99.5 x 380 mm

Operating temperature 5°C to 40°C

Operating humidity Less than 80% (no condensation)

TV format P

PAL-I (RD-XV47KB)

SECAM LL, PAL B / G (RD-XV47KF)

AL / SECAM - BG / DK (RD-XV47KE)

Recording

Recording format Video Recording format (DVD-RW only),

Video format (DVD-RW, DVD-R)

+VR format (DVD+RW, DVD+R)

Recordable discs DVD-ReWritable, DVD-Recordable, DVD+ReWritable,

DVD+Recordable

Video recording format

Sampling frequency

Compression format

13.5 MHz

MPEG2

Audio recording format

Sampling frequency

Compression format

48 kHz

Dolby Digital

Tuner

Receivable channels E2-

IRA-E69 (RD-XV47KB)

"L (SECAM L)": F1 - E69 (RD-XV47KF)

"BG (PAL B / G)": E2 - E69 (RD-XV47KF)

E69 (RD-XV47KE)

Input/Output

Front Panel : (AV3)

Video input

Input level

One RCA connector

1 Vp-p (75 Ω)

S-Video input

Input level

One Mini DIN 4-pin jack

Y (Iuminance) 1 Vp-p (75 Ω)

C (colour) 300 mVp-p (75 Ω)

Audio input

Input level

Two RCA connectors

2 Vrms (input impedance: more than 10 kΩ)

Rear Panel

VHF/UHF antenna input/output terminal VHF/UHF set 75 Ω

Audio input /output Two 21-pin scart sockets (AV1, AV2)

Video input /output

Input /output level

Two 21-pin scart sockets (AV1, AV2)

1Vp-p (75 Ω) each

S-Video output

Output level

One Mini DIN 4-pin jacks

Y (Iuminance) 1 Vp-p (75 Ω)

C (colour) 300 mVp-p (75 Ω)

Component video out

Output level

Three RCA connectors

Y: 1.0 Vp-p (75 Ω)

, P

: 0.7 Vp-p (75 Ω) each

Analogue audio output

Output level

Two RCA connectors

2 Vrms (output impedance: 680Ω)

Digital audio out

Output level

One Coaxial pin jack

500 mVp-p (75 Ω)

1-2-1 R3PLSP

LASER BEAM SAFETY PRECAUTIONS

This DVD player uses a pickup that emits a laser beam.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep

your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser

beam.

CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in

hazardous radiation exposure.

Location: Inside Top of DVD mechanism.

Do not look directly at the laser beam coming

from the pickup or allow it to strike against your

skin.

Drive Mechanism Assembly

Laser Beam Radiation

Laser Pickup

Turntable

1-3-1 DVD_SFNP

IMPORTANT SAFETY PRECAUTIONS

Product Safety Notice

Some electrical and mechanical parts have special

safety-related characteristics which are often not evi-

dent from visual inspection, nor can the protection

they give necessarily be obtained by replacing them

with components rated for higher voltage, wattage,

etc. Parts that have special safety characteristics are

identified by a !on schematics and in parts lists. Use

of a substitute replacement that does not have the

same safety characteristics as the recommended

replacement part might create shock, fire, and/or other

hazards. The Product’s Safety is under review continu-

ously and new instructions are issued whenever

appropriate. Prior to shipment from the factory, our

products are carefully inspected to confirm with the

recognized product safety and electrical codes of the

countries in which they are to be sold. However, in

order to maintain such compliance, it is equally impor-

tant to implement the following precautions when a set

is being serviced.

Precautions during Servicing

A. Parts identified by the !symbol are critical for

safety. Replace only with part number specified.

B. In addition to safety, other parts and assemblies

are specified for conformance with regulations

applying to spurious radiation. These must also be

replaced only with specified replacements.

Examples: RF converters, RF cables, noise block-

ing capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:

1)Wires covered with PVC tubing

2)Double insulated wires

3)High voltage leads

D. Use specified insulating materials for hazardous

live parts. Note especially:

1)Insulation tape

2)PVC tubing

3)Spacers

4)Insulators for transistors

E. When replacing AC primary side components

(transformers, power cord, etc.), wrap ends of

wires securely about the terminals before solder-

ing.

F. Observe that the wires do not contact heat produc-

ing parts (heatsinks, oxide metal film resistors, fus-

ible resistors, etc.).

G. Check that replaced wires do not contact sharp

edges or pointed parts.

H. When a power cord has been replaced, check that

5 - 6 kg of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations.

J. Be careful that foreign objects (screws, solder

droplets, etc.) do not remain inside the set.

K. When connecting or disconnecting the internal

connectors, first, disconnect the AC plug from the

AC outlet.

1-3-2 DVD_SFNP

Fig. 1

Chassis or Secondary Conductor

Primary Circuit

d' d

AC Voltmeter

(High Impedance)

Exposed Accessible Part

BOne side of

Power Cord Plug Prongs

Fig. 2

Safety Check after Servicing

Examine the area surrounding the repaired location

for damage or deterioration. Observe that screws,

parts, and wires have been returned to their original

positions. Afterwards, do the following tests and con-

firm the specified values to verify compliance with

safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm

specified clearance distance (d) and (d’) between sol-

dered terminals, and between terminals and surround-

ing metallic parts. (See Fig. 1)

Table 1 : Ratings for selected area

Note: This table is unofficial and for reference only.

Be sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current

between B (earth ground, power cord plug prongs)

and externally exposed accessible parts (RF termi-

nals, antenna terminals, video and audio input and

output terminals, microphone jacks, earphone jacks,

etc.) is lower than or equal to the specified value in the

table below.

Measuring Method (Power ON) :

Insert load Z between B (earth ground, power cord

plug prongs) and exposed accessible parts. Use an

AC voltmeter to measure across the terminals of load

Z. See Fig. 2 and the following table.

AC Line Voltage Clearance Distance (d), (d’)

230 V ≥3.2 mm(d)

≥6.0 mm(d’)

Table 2: Leakage current ratings for selected areas

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

AC Line Voltage Load Z Leakage Current (i) One side of power cord plug

prongs (B) to:

230 V

2kΩ RES.

Connected in

parallel

i≤0.7mA AC Peak

i≤2mA DC

RF or

Antenna terminals

50kΩRES.

Connected in

parallel

i≤0.7mA AC Peak

i≤2mA DC A/V Input, Output

1-4-1 DVDN_SN

STANDARD NOTES FOR SERVICING

Circuit Board Indications

1. The output pin of the 3 pin Regulator ICs is

indicated as shown.

2. For other ICs, pin 1 and every fifth pin are

indicated as shown.

3. The 1st pin of every male connector is indicated as

shown.

Instructions for Connectors

1. When you connect or disconnect the FFC (Flexible

Foil Connector) cable, be sure to first disconnect

the AC cord.

2. FFC (Flexible Foil Connector) cable should be

inserted parallel into the connector, not at an

angle.

Pb (Lead) Free Solder

When soldering, be sure to use the Pb free solder.

How to Remove / Install Flat Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:

1. Prepare the hot-air flat pack-IC desoldering

machine, then apply hot air to the Flat Pack-IC

(about 5 to 6 seconds). (Fig. S-1-1)

2. Remove the flat pack-IC with tweezers while

applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the

BOARD; when removing entire flat pack-IC, first

apply soldering iron to center of the flat pack-IC

and heat up. Then remove (glue will be melted).

(Fig. S-1-6)

4. Release the flat pack-IC from the BOARD using

tweezers. (Fig. S-1-6)

CAUTION:

1. The Flat Pack-IC shape may differ by models. Use

an appropriate hot-air flat pack-IC desoldering

machine, whose shape matches that of the Flat

Pack-IC.

2. Do not supply hot air to the chip parts around the

flat pack-IC for over 6 seconds because damage

to the chip parts may occur. Put masking tape

around the flat pack-IC to protect other parts from

damage. (Fig. S-1-2)

NOTE: BOARD MEANS PRINTED CIRCUIT BOARD.

Top View

Out In

Bottom View

Input

Pin 1

FFC Cable

Connector

BOARD

* Be careful to avoid a short circuit.

Fig. S-1-1

1-4-2 DVDN_SN

3. The flat pack-IC on the BOARD is affixed with

glue, so be careful not to break or damage the foil

of each pin or the solder lands under the IC when

removing it.

With Soldering Iron:

1. Using desoldering braid, remove the solder from

all pins of the flat pack-IC. When you use solder

flux which is applied to all pins of the flat pack-IC,

you can remove it easily. (Fig. S-1-3)

2. Lift each lead of the flat pack-IC upward one by

one, using a sharp pin or wire to which solder will

not adhere (iron wire). When heating the pins, use

a fine tip soldering iron or a hot air desoldering

machine. (Fig. S-1-4)

3. Bottom of the flat pack-IC is fixed with glue to the

BOARD; when removing entire flat pack-IC, first

apply soldering iron to center of the flat pack-IC

and heat up. Then remove (glue will be melted).

(Fig. S-1-6)

4. Release the flat pack-IC from the BOARD using

tweezers. (Fig. S-1-6)

Hot-air

Flat Pack-IC

Desoldering

Machine

BOARD

Flat Pack-IC

Tweezers

Masking

Tape

Fig. S-1-2

Flat Pack-IC Desoldering Braid

Soldering Iron

Fig. S-1-3

Fine Tip

Soldering Iron

Sharp

Fig. S-1-4

1-4-3 DVDN_SN

With Iron Wire:

1. Using desoldering braid, remove the solder from

all pins of the flat pack-IC. When you use solder

flux which is applied to all pins of the flat pack-IC,

you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting

point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering

iron or hot air blower, pull up the wire as the solder

melts so as to lift the IC leads from the BOARD

contact pads as shown in Fig. S-1-5.

4. Bottom of the flat pack-IC is fixed with glue to the

BOARD; when removing entire flat pack-IC, first

apply soldering iron to center of the flat pack-IC

and heat up. Then remove (glue will be melted).

(Fig. S-1-6)

5. Release the flat pack-IC from the BOARD using

tweezers. (Fig. S-1-6)

Note: When using a soldering iron, care must be

taken to ensure that the flat pack-IC is not

being held by glue. When the flat pack-IC is

removed from the BOARD, handle it gently

because it may be damaged if force is applied.

2. Installation

1. Using desoldering braid, remove the solder from

the foil of each pin of the flat pack-IC on the

BOARD so you can install a replacement flat pack-

IC more easily.

2. The “●” mark on the flat pack-IC indicates pin 1.

(See Fig. S-1-7.) Be sure this mark matches the 1

on the BOARD when positioning for installation.

Then presolder the four corners of the flat pack-IC.

(See Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that

none of the pins have solder bridges.

To Solid

Mounting Point

Soldering Iron

Iron Wire

Hot Air Blower

Fig. S-1-5

Fine Tip

Soldering Iron

BOARD

Flat Pack-IC

Tweezers

Fig. S-1-6

Example :

Pin 1 of the Flat Pack-IC

is indicated by a " " mark. Fig. S-1-7

Presolder

BOARD

Flat Pack-IC

Fig. S-1-8

Andere Handbücher für RD-XV47KE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba DVD-Recorder Handbücher

Toshiba

Toshiba D-R560 - DVD Recorder With TV Tuner Bedienungsanleitung

Toshiba

Toshiba D-R160SB Bedienungsanleitung

Toshiba

Toshiba DR570 - DVD Recorder With TV Tuner Bedienungsanleitung

Toshiba

Toshiba RD-XS34SU Bedienungsanleitung

Toshiba

Toshiba D-R4SU Bedienungsanleitung

Toshiba

Toshiba RD-X2U Bedienungsanleitung

Toshiba

Toshiba D-R255-SG Bedienungsanleitung

Toshiba

Toshiba D-R3 Bedienungsanleitung

Toshiba

Toshiba D-KR2SU Bedienungsanleitung

Toshiba

Toshiba W-808 Bedienungsanleitung

Toshiba

Toshiba D-R150SB Bedienungsanleitung

Toshiba

Toshiba RD-XS24SB Bedienungsanleitung

Toshiba

Toshiba D-KR10 Bedienungsanleitung

Toshiba

Toshiba DKR40KU Bedienungsanleitung

Toshiba

Toshiba D-R4SC Bedienungsanleitung

Toshiba

Toshiba D-R1SU Bedienungsanleitung

Toshiba

Toshiba DKR40 - DVD Recorder With 1080p Upconversion Bedienungsanleitung

Toshiba

Toshiba D-R4SU Bedienungsanleitung

Toshiba

Toshiba D-RW2SU/D-RW2SC Bedienungsanleitung

Toshiba

Toshiba D-VR30SG Bedienungsanleitung

Toshiba

Toshiba XS35 - RD - DVDr Bedienungsanleitung

Toshiba

Toshiba D-R5SC Bedienungsanleitung

Toshiba

Toshiba RD100KB Bedienungsanleitung

Toshiba

Toshiba DR550 - DVD Recorder With TV Tuner Bedienungsanleitung

Beliebte DVD-Recorder Handbücher anderer Marken

Pioneer

Pioneer DVR-65H-S Einrichtungshandbuch

Sony

Sony RDR-VX525 - DVDr/ VCR Combo Bedienungsanleitung

Daewoo

Daewoo DHD-4000D Bedienungsanleitung

Medion

Medion MD 40570 Bedienungsanleitung

Philips

Philips ShowView DVDR3460H Bedienungsanleitung

Sony

Sony RDR-GX355 - Tunerless DVD Recorder Bedienungsanleitung

Sony

Sony DVDirect VRD-MC3 Bedienungsanleitung

Samsung

Samsung DVD-R130/XAA Bedienungsanleitung

FUNAI

FUNAI HD-B2735 Bedienungsanleitung

Panasonic

Panasonic DMR-EH54DEG Bedienungsanleitung

Pioneer

Pioneer PRV-LX1 Technisches Handbuch

Sanyo

Sanyo DRW-1000 Bedienungsanleitung

Philips

Philips DVDR610/05 Bedienungsanleitung

JVC

JVC DR-M10 Bedienungsanleitung

Samsung

Samsung SV-DVD40 Bedienungsanleitung

Philips

Philips DVDR3355 Bedienungsanleitung

FUNAI

FUNAI FDR-90E Bedienungsanleitung

LG RC298 Bedienungsanleitung