Toshiba PCT001Z-E Bedienungsanleitung

E6581478

TOSVERT VF-AS1/PS1

Trace Tool PCT001Z-E

Instr ction Man al

Notes

1．

．．

． Be s re to read this man al caref lly before connecting and sing

the trace tool for the VF-AS1/PS1.

After reading the man al, be s re to store it.

2．

．．

． The contents of this man al are s bject to change witho t prior

notice.

E6581478

－ Contents －

Introduction ............................................................................................................................ 1

How to use PCT001Z-E......................................................................................................... 3

2.1.

NABLING MAC OS

............................................................................................................. 3

2.2.

ICENSE AG EEMENT

.......................................................................................................... 3

2.3.

PENING WINDOW

.............................................................................................................. 4

2.4.

ETTING SHEET

.................................................................................................................. 5

2.5.

APHIC SHEET

................................................................................................................ 10

2.6.

ATA SHEET

...................................................................................................................... 12

Troubleshooting ................................................................................................................... 14

E6581478

1.Introd ction

The trace tool “PCT001Z-E” for VF-AS1/PS1 is software that performs the following

functions when used with an inverter connected to a computer via an S-485

communications device. ead this manual carefully along with the instruction manual for

VF-AS1/PS1 before using PCT001Z-E and use it correctly.



Export and Import trace function-related parameters



eading information on the inverter



eading trace data



Displaying read trace data in graphic form



Storing trace data

*1 PCT001Z-E does not support any inverters other than VF-AS1/PS1.

*2 To use PCT001Z-E, the USB converters unit shown in Fig. 1 below are required.



USB converters unit (part

○

in this figure)



Inverter interconnect cable (part

○

in this figure)



Computer interconnect cable (part

○

in this figure)

S485 (2-wire type)

USB

LOGIC

USB

Option Unit

○

 Inverter interconnect cable (optional)

Model number Cable length

CAB0011 1.2m

CAB0013 3.6m

CAB0015 4.8m

 USB cable (A-B connection type)

Prepare a commercially available USB cab

(USB1.1/2.0-compliant).

ecommended cable length: 1m

 Model No. of USB

converters

unit:

USB001Z

Fig. 1 An example of connection of USB converters unit

E6581478

*3 System requirements

Personal computer with Microsoft

○

Excel

○

installed

Others: A serial port or a USB port is required for the computer to connect to the

inverter.

It is recommendable to use a mouse or a similar pointing device for operation.

*4 PCT001Z-E may not run normally on some types of PC-98 series computers.

*5 It has been confirmed that PCT001Z-E runs normally on the software listed in the table

below.

Microsoft Excel MS-Excel 2000 MS-Excel 2003

English version ○ ○

*6 When using an optional USB communication converter, connect the converter before

starting PCT001Z-E. Do not plug or unplug the connector when PCT001Z-E is running.

*7 How to install PCT001Z-E

To install PCT001Z-E, just extract the zip file and move it into the desired folder.

Take the following precautions when installing PCT001Z-E.



Exit running application programs.



When updating latest PCT001Z-E, uninstall the old version of PCT001Z-E. (The version

of PCT001Z-E is shown in the Opening window (section 2.3).)

*8 How to uninstall PCT001Z-E

To uninstall PCT001Z-E, just remove the folder containing PCT001Z-E from the

computer.

☆ The specifications of this software is subject to change without notice.

☆ Toshiba Schneider Inverter assumes no responsibility for damage caused directly or

indirectly by the use or a malfunction of this software product.

☆ These system requirements are minimum conditions required for the use of PCT001Z-E.

They do not guarantee that all functions of PCT001Z-E are performed normally.

☆ Windows

○

is listed as the abbreviation for a Microsoft

○

Windows

○

operating system.

Microsoft

○

Windows

○

and Microsoft

○

Excel

○

are registered trademarks or trademarks

of the US Microsoft Corporation in the USA and other countries.

☆ PC-98 series is a trademark or registered trademark of NEC Corporation.

☆ The symbols used in this manual have the following meanings.

[ ]: Buttons or radio buttons in windows of PCT001Z-E or Microsoft Windows

' ': Menus items of PCT001Z-E

E6581478

2.How to se PCT001Z-

-E

This section explains how to use PCT001Z-E.

2.1.Enabling macros

When PCT001-E is started for the first time, the dialog box shown in Fig. 2 may appear. If it

appears, click the [Enable Macros] button, because PCT001Z-E uses macros.

Fig. 2 Security warning

2.2.License agreement

When PCT001Z-E is started for the first time or after macros have been enabled, the

PCT001Z-E license agreement window (Fig. 3) appears. ead the contents carefully and

click [agree] if you wish to use PCT001Z-E. Clicking [don’t agree] closes the Excel book.

Fig. 3 License agreement

E6581478

2.3.Opening window

When macros are executed, the Opening sheet (Fig. 4) appears. After reading the

instruction manual (this manual) carefully, click [To setting >] in the top-right of the window

and make necessary settings.

Fig. 4 Opening window

① [To setting >]

Click this button to move from the Opening sheet to the Setting sheet.

E6581478

2.4.Setting sheet

The Setting sheet (Fig. 5) allows you to make settings necessary for communications

between the inverter and the computer and to write and read related parameters.

Fig. 5 Setting sheet

② Communication setting

Fig. 6 Communication setting

'COM Port': Specify the COM port number of the computer.

'Baud rate': Specify the baud rate (F800) of the inverter.

'Parity': Specify the parity (F801) of the inverter.

'Inverter number': Specify the number (F802) assigned to the inverter.

Since PCT001Z-E uses the Toshiba inverter protocol ASCII mode, only a number

between 0 and 99 can be assigned to an inverter.

*1 If you select a parameter other than parameters set for the inverter or the computer

connected to it, an error may occur during communication.

E6581478

Table 1 Table of settings for communications with inverter

Title Content Adjustment range Default

setting

- COM port 1~30 -

F800 Baud rate 0:9600bps 1:19200bps 2:38400bps 1

F801 Parity 0:Non parity 1:Even parity 2:Odd parity 1

F802 Inverter number 0~99 0

③ Parameter concerning trace function

Fig. 7 Parameter concerning trace function

'Constant at the time of filtering': Select the size of constant at the time of filtering (F678).

'Trace selection': Select the trace data acquisition timing (F740).

'Trace cycle': Select the trace cycle (F741).

'Trace data1': Select type1 (F742) of data.

'Trace data2': Select type2 (F743) of data.

'Trace data3': Select type3 (F744) of data.

'Trace data4': Select type4 (F745) of data.

*2 Set all trace-related parameters before operating the inverter. If after the inverter did

trip or trigger that it is changed, that data cannot be read.

*3 Take special care when using analog output signals (FM and AM terminals) with the

inverter.

The constant at the time of filtering (F678) also acts on analog output signals.

Therefore, if there is a probability that these output signals will affect the machine, do

not change the value of constant at the time of filtering.

By default, the constant is set at 64ms.

E6581478

Table2 Parameter concerning trace functions

Title Content Adjustment range Default

setting

F678 Constant at the

time of filtering 4ms~100ms

F740 Trace selection 0:Deselect 1:At tripping 2:At triggering 1

F741 Trace cycle 0:4ms 1:20ms 2:100ms 3:1s 4:10s 2

F742

Trace data1

00:Output frequency (Hz)

01:Frequency command value (Hz)

02:Output current (%)

03:Input voltage (%)

04:Output voltage (%)

05:Compensated frequency (Hz)

06:Speed feedback (real-time value) (Hz)

07:Speed feedback (1-second filter) (Hz)

08:Torque (%)

09:Torque command (%)

11:Torque current (%)

12:Exciting current (%)

13:PID feedback value (Hz)

14:Motor overload factor (OL2 data) (%)

15:Inverter overload factor (OL1 data) (%)

16: egenerative braking resistance overload

factor (OLr data) (%)

17: egenerative braking resistor load factor

(%ED) (%)

18:Input power (kW)

19:Output power (kW)

23:Option AI2 input (%)

24: /S4 input (%)

25:VI/II input (%)

26: X input (%)

27:Option AI1 input (%)

28:FM output (%)

29:AM output (%)

34:Integral input power (kWhr)

35:Integral output power (kWhr)

46:My Function Monitor1

47:My Function Monitor2

48:My Function Monitor3

49:My Function Monitor4

F743

Trace data2

Same as trace data1

F744

Trace data3

Same as trace data1

F745

Trace data4

Same as trace data1

*4 5, 6, and 7ms are set as 4ms.

*5 My Function monitors 1 through 4 at 46 through 49 cannot be specified with any

parameter between F742 and F745 (kinds of data to be acquired).

E6581478

④ Inverter individual information

Fig. 8 Inverter individual information

'Inverter form': Displays the type of the inverter.

'Serial number': Displays the serial number of the inverter.

'CPU1 Ver': Displays the version of the inverter’s CPU1.

'CPU2 Ver': Displays the version of the inverter’s CPU2.

'Inverter operating time': Displays the operating time of the inverter.

⑤ [Parameter export]

Click this button to write the values set for the trace-related parameters (Fig. 7) into the

inverter.

⑥ [Parameter import]

Click this button to read the values set for the trace-related parameters (Fig. 7) and

information on the inverter (Fig. 8).

⑦ [To graph >]

Click this button to move from the Setting sheet to the Graphic sheet.

⑧ [A set value of constant at the time of filtering is not changed.]

If this radio button is checked, clicking [Parameter export] will not change the value of

constant at the time of filtering. (Select this option under normal conditions.)

⑨ [ ecommended value of constant at the time of filtering is set by the automatic set up.]

If this radio button is checked, clicking [Parameter export] will write the value of constant

at the time of filtering recommended for the trace cycle into the inverter. The value set

with F678 (constant at the time of filtering), however, does not take effect.

The table below shows correspondences between trace cycle and recommended value

of constant at the time of filtering.

Table 3 Correspondence between trace cycle and recommended value

of constant at the time of filtering

Trace cycle 4ms 20ms

100ms

1s 10s

Constant at the time of filtering

4ms 10ms

64ms

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Wechselrichter Handbücher

Toshiba

Toshiba TOSVERT VF-S11 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-AS1 Series Bedienungsanleitung

Toshiba

Toshiba H9 Bedienungsanleitung

Toshiba

Toshiba ACE-tronics G9 ASD Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-A7 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S11 Bedienungsanleitung

Toshiba

Toshiba Tosvert VF-A3 Bedienungsanleitung

Toshiba

Toshiba Q-Flowsaver II Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S15 series Bedienungsanleitung

Toshiba

Toshiba Q7 Flow Bedienungsanleitung

Toshiba

Toshiba WAM600AR-SV-8 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S15 series Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S11 Konfigurationshandbuch

Toshiba

Toshiba TOSVERT VF-PS1 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S15 series Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-PS1 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S9 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-MB1 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-FS1 Series Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-S11 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-MB1 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-AS1 Series Bedienungsanleitung

Toshiba

Toshiba Tosvert VF-A3 Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-AS1 Series Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung