Toshiba 15VL56B Bedienungsanleitung

SERVICE MANUAL

LCD Color Television

15VL56B

20VL56B

20VL56G

FILE NO. 050-200533

Published in Japan, Sep. 2005 (YC)

TOSHIBA CORPORATION, 2005

TABLE OF CONTENTS

SERVICE SAFETY PRECAUTIONS ................................................................................................................................... 3

HANDLING THE LCD MODULE ......................................................................................................................................... 5

1. SERVICE MODE ............................................................................................................................................................. 7

1-1. STARTING SERVICE MODE .................................................................................................................................... 7

2. ADJUSTMENT ................................................................................................................................................................ 9

2-1. ADJUSTMENT TOOLS AND CONDITIONS ............................................................................................................ 9

2-2. AUTO GAIN/OFFSET ADJUSTMENT ...................................................................................................................... 9

2-3. DDC EDID DATA READ & WRITE .......................................................................................................................... 10

3. VCTI FIRMWARE INSTALLATIONS/UPGRADING ....................................................................................................... 20

3-1. VCTI FIRMWARE INSTALLATIONS ....................................................................................................................... 21

3-2. SCALER FIRMWARE INSTALLATIONS ................................................................................................................. 27

4. TROUBLESHOOTING ................................................................................................................................................... 34

5. EXPLODED VIEW ......................................................................................................................................................... 39

6. CHASSIS AND CABINET REPLACEMENT PARTS LIST ............................................................................................ 40

7. PC BOARDS TOP & BOTTOM VIEW ............................................................................................................................ 49

8. SCHEMATIC DIAGRAM ................................................................................................................................................ 52

8-1. WIRING DIAGRAM ................................................................................................................................................. 53

8-2. BLOCK DIAGRAM (20VL56B/G) ............................................................................................................................ 54

8-3. BLOCK DIAGRAM (15VL56B) ................................................................................................................................ 55

9. SPECIFICATIONS ......................................................................................................................................................... 74

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

SERVICE SAFETY PRECAUTIONS

• The caution items shown here describe major safety issues and should always be observed.

• The meanings of the various indications are as follows.

WARNING

CAUTION

Indicates a hypothetical situation in which service personnel and nearby third parties, or even

end users due to a product defect after the service operation is completed, could possibly be in

danger of injury or even death in the event of operational error.

Indicates a hypothetical situation in which service personnel and nearby third parties, or even

end users after the service operation is completed, could possibly be in danger of injury, or

where there could be physical damage in the event of operational error.

* Physical damage means major damage to a home, furnishings and other possessions.

Examples of marks

SHOCK HAZARD

PROHIBIT DISASSEM-

BLING

UNPULUG

The

indicates caution (including danger and warning).

The actual meaning of this caution is indicated inside the

or nearby illustrations or text.

The example shown to the left indicates the danger of "electrical shock".

The indicates a forbidden action.

The actual meaning of this caution is indicated inside the or nearby illustrations or text.

The example shown to the left indicates that disassembly is forbidden.

The

indicates a forced action (an action that must be performed).

The actual meaning of this forced action is indicated by

or nearby illustrations or text.

The example shown to the left indicates that the power plug must be disconnected.

WARNING

KEEP CHILDREN

AWAY

UNPULUG

SHOCK HAZARD

USE SPECIFIED

PARTS

CAUTION FOR

WIRING

CAUTION FOR

ASSEMBLING /

WIRING

CHECK INSULATION

RESISTANCE

PROHIBIT

REMODELING

• Always advise users to keep children away.

There is danger of injury to children from tools, disassembled products, etc.

• Always disconnect the power plug before starting work whenever power is not required.

Failure to disconnect the power plug before starting work can result in electrical shock.

• Depending on the model, use an insulation transformer or wear gloves when servicing with the

power on, and disconnect the power plug to avoid electrical shock when replacing parts.

In some cases, alternating current is also impressed in the chassis, so electrical shock is pos-

sible if the chassis is contacted with the power on.

• Always use the replacement parts specified for the particular model when making repairs.

The parts used in products have the necessary safety characteristics such as inflammability,

voltage resistance, etc.; therefore, use only replacement parts that have these same character-

istics.

Use only the specified parts when the mark is included in a circuit diagram or parts list.

• Parts mounting and routing of the wiring should be the same as that used originally.

For safety purposes, insulating materials such as tubing or tape is sometimes used and printed

circuit boards are sometimes mounted floating.

Also make sure that wiring is routed and clamped to avoid parts that generate heat and which

use high voltage. Always follow the original scheme.

• After a repair has been completed, reassemble all disassembled parts, and route and recon-

nect the wiring, in accordance with the original scheme.

Do not allow internal wiring to be pinched by cabinets, panels, etc.

Any error in reassembly or wiring can result in electrical leakage, flame, etc., and may be

hazardous.

• After completing the work, disconnect the power plug from the outlet, remove the antenna, turn

on the power switch. Then, use a 500V insulation resistance meter to check the insulation

resistance of the antenna terminal, other metallic parts and between the prongs of the power

plug to make sure that the insulation resistance is 1M 1or more.

The set will require inspection and repair if the insulation resistance is below this value.

• Never remodel the product in any way.

Remodeling can result in improper operation, malfunction, or electrical leakage and flame,

which may be hazardous

HANDLING THE LCD MODULE

Safety Precautions

In the event that the screen is damaged or the liquid crystal

(fluid) leaks, do not breathe in or drink this fluid. Also, never

touch this fluid.

Such actions could cause toxicity or skin irritation. If this fluid

should enter the mouth, rinse the mouth thoroughly with wa-

ter. If the fluid should contact the skin or clothing, wipe off

with alcohol, etc., and rinse thoroughly with water. If the fluid

should enter the eyes, immediately rinse the eyes thoroughly

with running water.

Precautions for Handling the LCD Module

The LCD module can easily be damaged during disassembly

or reassembly; therefore, always observe the following pre-

cautions when handling the module.

1. When attaching the LCD module to the LCD cover, posi-

tion it appropriately and fasten at the position where the

display can be viewed most conveniently.

2. Carefully align the holes at all four corners of the LCD

module with the corresponding holes in the LCD cover

and fasten with screws. Do not strongly push on the mod-

ule because any impact can adversely affect the perform-

ance. Also use caution when handling the polarized screen

because it can easily be damaged.

CAUTION The metal edges of the LCD module

are sharp, handle it with care.

3. If the panel surface becomes soiled, wipe with cotton or

soft cloth. If this does not remove the soiling, breathe o

the surface and then wipe again.

If the panel surface is extremely solied, use a CRT cleane

as a cleaner.Wipe off the panel surface by drop the cleane

on the cloth. Do not drop the cleaner on the panel. Pa

attention not to scratch the panel surface.

4. Leaving water or other fluids on the panel screen for a

extended period of time can result in discoloration o

stripes. Immediately remove any type of fluid from th

screen.

5. Glass is used in the panel, so do not drop or strike wit

hard objects. Such actions can damage the panel.

6. CMOS-LSI circuitry is used in the LCD module, so avoi

damage due to static electricity. When handling the mod

ule, use a wrist ground or anchor ground.

7. Do not expose the LCD module to direct sunlight or strong

ultraviolet rays for an extended period of time.

8. Do not store the LCD module below the temperature con-

ditions described in the specifications. Failure to do so

could result in freezing of the liquid crystal due to cold air

or loss of resilience or other damage.

9. Do not disassemble the LCD module. Such actions could

result in improper operation.

10. When transporting the LCD module, do not use packing

containing epoxy resin (amine) or silicon resin (alcohol or

oxim). The gas generated by these materials can cause

loss of polarity.

Scaler ADCScaler ADC

9883ADC

VCTIADC

Audio

Option 1

Option 2

Option 3

DRX Set

NVM Edit

Download

Reset TV

Hotel Mode

FrequencyFrequency 47054705

Gm2221Gm2221 Ver. 3. 22.Ver. 3. 22.

VCTiVCTi Ver. 3. 49.Ver. 3. 49.

Service Menu

1.Service Mode

1-1.Starting Service Mode

*Set LCD TV to the normal TV signal receive mode.

Note: In this "Service Mode" section, [ ] shows a button.

1-1-1. Press [MUTE] on the remote control once.

1-1-2. Press [MUTE] again, and press [ ] on LCD TV.

Service mode displayed on TV screen

VCTi version

Items other than those enclosed by are default

settings.

*For EU,Hotel mode setting is not a vailable.

Scaler version

15VL56B

Option 1 15VL56B

SAV 1

SCART 1

PC 1

Side Comp 0

16:9 0

200 PR 0

Tex t 1

ACMS 1

Option 2 15VL56B

HiDev 0

Hotel 0

To p 1

I ll SAVE 0

Turbo Vol 0

Ch/Aus 0

Option 3 15VL56B

Language 0

Txt Lang 7

Inch opt 2

PA N E L 0

20VL56B/G

Option 1 20VL56B 20VL56G

SAV 1 1

SCART 1 1

PC 1 1

Side Comp 0 0

16:9 0 0

200 PR 0 0

Tex t 1 1

ACMS 1 1

Option 2 20VL56B 20VL56G

HiDev 0 0

Hotel 0 0

To p 1 1

I ll SAVE 0 0

Turbo Vol 0 0

Ch/Aus 0 0

Option 3 20VL56B 20VL56G

Language 0 0

Txt Lang 7 7

Inch opt 3 3

PA N E L 0 0

OPTION DEFAULT DATA

2. Adjustment

Note: In this "Adjustment" section, [ ] shows a button.

2-1.Adjustment Tools and Conditions

Tools: Pattern Generator (801GF, MSPG925F)

DDC Adjustment Tool

Remote Control

Conditions: Heat Run 30 minutes or more

2-2. Auto Gain/Offset Adjustment

2-2-1. RF Mode Adjustment (normal TV receive mode)

No reguired

2-2-2. Component Mode Adjustment

Preparation

Carry out Heat Run for 30 minutes or more before

adjustment (with no RF signal).

1) Connect Y, Pb, and Pr output signals of Pattern Generator

to the component jack (Y, Pb, Pr) of LCD TV.

2) Connect Y, Pb, and Pr output signals of Pattern

Generator to the component jack (D Jack) of LCD TV.

3) Change the TV input mode to component mode.

4) Select 480p Mode (Y:100% Pb/Pr:75%) in Pattern Generator. Select Pattern 33 (Color Bar

Pattern signal) in Pattern Generator (MSPG925F).

5) Go into service mode, and Auto Gain menu appears, and then press VOL [+].

6) Press [OK] to store the adjustment data.

2-2-3. PC Mode Adjustment

Preparation

Carry out Heat Run for 30 minutes or more before adjustment (with no RF signal).

Connect Pattern Generator to the 15-pin D-Sub Jack of LCD TV.

1) Change the TV input mode to PC mode.

2) Set Pattern Generator to the following:

15VL56B : XGA (1024x768) 16-step or 11-step grayscale

20VL56B,20VL56G : VGA (640x480) 16-step grayscale

3) Go into service mode, and Auto Gain menu appears, and then press VOL [+].

4) Press [OK] to store the adjustment data.

(Adjustment in component mode or PC mode)

2-3. DDC EDID Data Read & Write

The following software programs are used to read/write DDC EDID data.

DLPortIO.exe

t15.edi

t20.edi

UserPort.exe

UserPort.sys

J(Windows/system32/Drivers)

WinEDID_2.0.exe

Be very careful that DDC EDID data read/write varies depending on Operating System conditions

of PC.

(See the ﬂowchart below.)

Start

OS: MS Windows 2000, XP

OS: MS Windows 98

Port Setup: (2-3-1)

Preparation EDID Reading & Writing: (2-3-2)

EDID Read: (2-3-3)

EDID Write: (2-3-4)

Conﬁrmation of Updated EDID Data: (2-3-5)

Andere Handbücher für 15VL56B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba LCD-Fernseher Handbücher

Toshiba

Toshiba 15VL56B Bedienungsanleitung

Toshiba

Toshiba 26AV502R - 26" LCD TV Bedienungsanleitung

Toshiba

Toshiba REGZA 46RV530U Bedienungsanleitung

Toshiba

Toshiba 32E200U Bedienungsanleitung

Toshiba

Toshiba 37HL67S Bedienungsanleitung

Toshiba

Toshiba 42X3030D Bedienungsanleitung

Toshiba

Toshiba WL66/67 Bedienungsanleitung

Toshiba

Toshiba 22EL833N Bedienungsanleitung

Toshiba

Toshiba 32W2453RK Bedienungsanleitung

Toshiba

Toshiba 46G300U Bedienungsanleitung

Toshiba

Toshiba 32DL66Ps Bedienungsanleitung

Toshiba

Toshiba WL56 Series Bedienungsanleitung

Toshiba

Toshiba 46WX800 Bedienungsanleitung

Toshiba

Toshiba 19AV501U - 19" LCD TV Bedienungsanleitung

Toshiba

Toshiba 26EL834G Bedienungsanleitung

Toshiba

Toshiba 37X3030D Bedienungsanleitung

Toshiba

Toshiba 26WL46B Bedienungsanleitung

Toshiba

Toshiba 32 LK3A Series Bedienungsanleitung

Toshiba

Toshiba 42SL417U Bedienungsanleitung

Toshiba

Toshiba 36ZP46 Series Bedienungsanleitung

Toshiba

Toshiba 40RV52R Bedienungsanleitung

Toshiba

Toshiba 32CV700E Bedienungsanleitung

Toshiba

Toshiba 26AV500U - 26" LCD TV Bedienungsanleitung

Toshiba

Toshiba M74 Series Bedienungsanleitung

Beliebte LCD-Fernseher Handbücher anderer Marken

LG 32LC4R* Bedienungsanleitung

Samsung

Samsung LA32E420 Leitfaden

Dell

Dell W1900 19 Gebrauchsanweisung

Samsung

Samsung LN40C670M1F Bedienungsanleitung

Runco

Runco CX-52HD Bedienungsanleitung

Sharp

Sharp LC-32AX3H Bedienungsanleitung

Philips

Philips 47PFL7704D Bedienungsanleitung

Vizio

Vizio VO42LFHDTV10A Bedienungsanleitung

Philips

Philips 42PF7520D/79 Bedienungsanleitung

Insignia

Insignia NS-LCD32-09 Bedienungsanleitung

Sony

Sony WEGA KLV-27HR3 Bedienungsanleitung

Nexus

Nexus NX32031 Bedienungsanleitung

Zenith

Zenith Z32LC2D Bedienungsanleitung

Sony

Sony KDL-32S3000R - 32" Class Bravia S-series Digital Lcd... Bedienungsanleitung

Medion

Medion MEDION LIFE X14330 Bedienungsanleitung

Vizio

Vizio HDTV30A VW32L Bedienungsanleitung

Sharp

Sharp LC-24DV250K Bedienungsanleitung

SOYO

SOYO Dymond DYLT032A Bedienungsanleitung