Toshiba TD-Z552 Bedienungsanleitung

1



Service Manual

LCD TV

Model No. TD-Z552



WARNING

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not

contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by

electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or

products dealt with in this service information by anyone else could result in serious injury or death.

There are special components used in this equipment which are important for safety. These are marked by in the Schematic Diagrams,

Circuit Board Diagrams. Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with

manufacture’s specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

Unauthorized copying and distribution is a

violation of law.

2

TABLEOFCONTENTS Page

1 Safety Precautions.....................................................................................................................................................3

1.1. General Guidelines......................................................................................................................................................3

2 Warning........................................................................................................................................................................4

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices................................4

2.2. About lead free solder (PbF)......................................................................................................................................5

3 Service Navigation......................................................................................................................................................6

4 Specifications..............................................................................................................................................................7

5 Troubleshooting Guide..............................................................................................................................................9

5.1. No power.......................................................................................................................................................................9

5.2. Can’t start...................................................................................................................................................................10

5.3. Abnormal Display.......................................................................................................................................................11

5.4. No display...................................................................................................................................................................12

5.5. Sound problem...........................................................................................................................................................13

5.6. Remote control malfunction.....................................................................................................................................14

5.7. OSD is unstable or can’t work normally.................................................................................................................15

6 Block Diagram...........................................................................................................................................................16

7 Schematic Diagrams................................................................................................................................................18

7.1. Main Board.................................................................................................................................................................18

7.2. Power Board...............................................................................................................................................................38

7.3. Key Board...................................................................................................................................................................39

7.4. FAN Board..................................................................................................................................................................40

7.5. Daughter Board..........................................................................................................................................................41

7.6. IR Board......................................................................................................................................................................42

8 PCB Pattern Diagram...............................................................................................................................................43

8.1. Main Board.................................................................................................................................................................43

8.2. Power Board...............................................................................................................................................................45

8.3. Key Board...................................................................................................................................................................48

8.4. FAN Board..................................................................................................................................................................49

8.5. Daughter Board..........................................................................................................................................................49

8.6. IR Board......................................................................................................................................................................51

9 Exploded View and Replacement Parts List.........................................................................................................52

9.1. Exploded View...........................................................................................................................................................52

9.2.Replacement Parts List.............................................................................................................................................53

3

1 Safety Precautions

1.1. General Guidelines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been

overheated or damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are

properly installed.

3. After servicing, make the following leakage current checks to prevent the customer from being exposed to

shock hazards.

4. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.

5. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or

some of the wires have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the

entire wiring unit instead.

6. When conducting repairs and servicing, do not twist the Faston connectors but plug them straight in or unplug

them straight out.

1.1.1. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between

the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed

metallic cabinet part on the equipment such as

screwheads, connectors, control shafts, etc. When

the exposed metallic part has a return path to the

chassis, the reading should be 100 Mohm and

over. When the exposed metal does not have a

return path to the chassis, the reading must be

1.1.2. Leakage Current Hot Check (See Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do

not use an isolation transformer for this check.

2. Connect a 1.5kohm, 10 watts resistor, in parallel

with 0.15μF capacitors, between each exposed

metallic part on the set and a good earth ground

such as a water pipe, as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or

more sensitivity, to measure the potential

across the resistor.

4. Check each exposed metallic part, and

measure the voltage at each point.

5. Reverse the AC plug in the AC outlet and

repeat each of the above measurements.

6. The potential at any point should not exceed

0.75 volts RMS. A leakage current tester

(Simpson Model 229 or equivalent) may be

used to make the hot checks, leakage current

must not exceed 1/2 milliamp. In case a

measurement is outside of the limits specified,

there is a possibility of a shock hazard, and the

equipment should be repaired and rechecked

before it is returned to the customer.

Figure 1

4

2 Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly

are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some

field-effect transistors and semiconductor [chip] components. The following techniques should be used to help

reduce the incidence of component damage caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off

any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially

available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying

power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface

such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD

protected)] can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to

install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive

foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the

protective material to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion

such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate

static electricity (ESD) sufficient to damage an ES device).

5

2.2. About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements.

In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.

The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair

work, we’d suggest the use of Pb free solder as well, although Pb solder may be used.

PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.

Caution

• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F

(30~40 °C) higher. Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).

• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before

applying Pb solder.If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

• After applying PbF solder to double layered boards, please check the component side for excess solder which

may flow onto the opposite side. (see figure below)

Suggested Pb free solder

There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper)

solder. However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.

6

3 Service Navigation

Board Name Function Remarks

Main Board Speaker out, AV Terminal, HDMI in, SD Card, PC

in, Digital Signal Processor, Nile-Tcon, Tuner

All boards are non

serviceable and should

be exchanged for service

IR Board Remote Receiver, LED

Power Board Power (AC/DC), DC-DC

Key Board Control Button, Power switch

IR Board IR Pass-through Connection

Daughter Board Connect with OPS

Main Board

Power Board

Key Board

IR Board

Daughter

Board

7

4 Specifications

8

9

5 Troubleshooting Guide

5.1. No power

No power (LED “Off”)

Check the AC input and

the

ower is “ON”? Power “On”

Check the IR board and LED

Replace the main board

Power board output=5V? Replace the power board

Yes

Replace the IR board

10

5.2. Can’t start

Can’t start（LED red）

Replace the main board

Replace the Power board

Yes

Check the power key is

under control?

Check the IR receiver is

normal?

Replace the power board

Replace the key board

Yes

Replace the IR board

Power board output＝

16/24V?

Inhaltsverzeichnis

Andere Toshiba LCD-Fernseher Handbücher

Toshiba

Toshiba 26AV502U - 26" LCD TV Bedienungsanleitung

Toshiba

Toshiba 40AV10E Bedienungsanleitung

Toshiba

Toshiba 32W2453RK Bedienungsanleitung

Toshiba

Toshiba 46XV640U - 46" LCD TV Bedienungsanleitung

Toshiba

Toshiba 32W23 DIGITAL Series Bedienungsanleitung

Toshiba

Toshiba Stasis 20VL43 Bedienungsanleitung

Toshiba

Toshiba 37A3030D Bedienungsanleitung

Toshiba

Toshiba 32AV500U - 32" LCD TV Bedienungsanleitung

Toshiba

Toshiba 19BL502B2 Gebrauchsanweisung

Toshiba

Toshiba 32TL515U Bedienungsanleitung

Toshiba

Toshiba REGZA 26HL47 Bedienungsanleitung

Toshiba

Toshiba 26AV502U - 26" LCD TV Bedienungsanleitung

Toshiba

Toshiba 26AV52R Service-Handbuch

Toshiba

Toshiba 32W1333B Bedienungsanleitung

Toshiba

Toshiba 42AV500U Bedienungsanleitung

Toshiba

Toshiba 22AV500U - 22" LCD TV Bedienungsanleitung

Toshiba

Toshiba 26A3000P Leitfaden

Toshiba

Toshiba 37AV502U - 37" LCD TV Bedienungsanleitung

Toshiba

Toshiba 26HLV66 - 26" LCD TV Bedienungsanleitung

Toshiba

Toshiba TheaterWide 32HL95 Bedienungsanleitung

Toshiba

Toshiba 17WLT46B Bedienungsanleitung

Toshiba

Toshiba 42WLT66 Bedienungsanleitung

Toshiba

Toshiba 65UA3A Series Bedienungsanleitung

Toshiba

Toshiba 22DL704B Bedienungsanleitung

Beliebte LCD-Fernseher Handbücher anderer Marken

LG 32LC4R* Bedienungsanleitung

Samsung

Samsung LA32E420 Leitfaden

Dell

Dell W1900 19 Gebrauchsanweisung

Samsung

Samsung LN40C670M1F Bedienungsanleitung

Runco

Runco CX-52HD Bedienungsanleitung

Sharp

Sharp LC-32AX3H Bedienungsanleitung

Philips

Philips 47PFL7704D Bedienungsanleitung

Vizio

Vizio VO42LFHDTV10A Bedienungsanleitung

Philips

Philips 42PF7520D/79 Bedienungsanleitung

Insignia

Insignia NS-LCD32-09 Bedienungsanleitung

Sony

Sony WEGA KLV-27HR3 Bedienungsanleitung

Nexus

Nexus NX32031 Bedienungsanleitung

Zenith

Zenith Z32LC2D Bedienungsanleitung

Sony

Sony KDL-32S3000R - 32" Class Bravia S-series Digital Lcd... Bedienungsanleitung

Medion

Medion MEDION LIFE X14330 Bedienungsanleitung

Vizio

Vizio HDTV30A VW32L Bedienungsanleitung

Sharp

Sharp LC-24DV250K Bedienungsanleitung

SOYO

SOYO Dymond DYLT032A Bedienungsanleitung