Toshiba 52HMX84 - Cinema Series HD Bedienungsanleitung

SERVICE MANUAL

Projection Television

52HMX84

62HMX84

FILE NO. 020-200418

REVISED.2

Published in Japan, Jan. 2005 (YC)

TABLE OF CONTENTS

CHAPTER 1 GENERAL ADJUSTMENTS

SAFETY INSTRUCTIONS .............................................................................................................................................. 3

SERVICE MODE ............................................................................................................................................................ 4

CHAPTER 2 SPECIFIC INFORMATIONS

SETTING & ADJUSTING DATA...................................................................................................................................... 7

LOCATION OF CONTROLS ........................................................................................................................................... 8

PROGRAMMING CHANNEL MEMORY....................................................................................................................... 10

LAMP UNIT REPLACEMENT....................................................................................................................................... 12

PARTS REPLACEMENT IN LIGHT ENGINE...............................................................................................................

LIGHT ENGINE REPLACEMANT.................................................................................................................................

EXPLODED VIEW........................................................................................................................................................ 19

MECHANICAL DISASSEMBLY .................................................................................................................................... 20

CHASSIS REPLACEMENT PARTS LIST ..................................................................................................................... 21

PC BOARDS TOP AND BOTTOM VIEW..................................................................................................................... 29

TERMINAL VIEW OF TRANSISTORS ......................................................................................................................... 41

CIRCUIT BLOCK DIAGRAM ........................................................................................................................................ 44

SPECIFICATIONS .................................................................................................................................................... END

APPENDIX:

CIRCUIT DIAGRAM

Many electrical and mechanical parts in this chassis have special safety-related characteristics.These characteristics are

often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained byusing

replacement components rated for higher voltage, wattage, etc.Replacement parts which have these special safety charac-

teristics are identified in this manual and its supplements;electrical components having such features are identified by the

international hazard symbols on the schematic diagram and the parts list.

Before replacing any of these components, read the parts list in this manual carefully.The use of substitute replacement

parts which do not have the same safety character istics as specified in the parts list may create shock, fire, or other hazards.

PRODUCT SAFETY NOTICE

CHAPTER 1 GENERAL ADJUSTMENTS

SAFETY INSTRUCTIONS

WARNING:Service should not be attempted by anyone unfamiliar with the necessary precautions on this receiver.The following

are the necessary precautions to be observed before servicing this chassis.

1. An isolation transformer should be connected in the power line between the receiver and the AC line before any service is

performed on the receiver.

2. When replacing a chassis in the cabinet, always be certain that all the prospective devices are put back in place, such as;

non-metallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc.

SAFETY PRECAUTION

3. SELECTING THE ADJUSTING ITEMS

1) Every pressing of CHANNEL button in the service mode changes the adjustment items in the order of table-2.

( button for reverse order)

Refer to table-1 for preset data of adjustment mode.

(See SETTING & ADJUSTING DATA on page 8)

4. ADJUSTING THE DATA

1) Pressing of VOLUME or button will change the value of data in the range from 00H to FFH.The variable range

depends on the adjusting item.

5. EXIT FROM SERVICE MODE

1) Pressing POWER button to turn off the TV once.

SERVICE MODE

1. ENTERING SERVICE MODE

MUTE

(Service mode display)

3) While pressing the MUTE button,

press MENU button onTV set.

2) Press MUTE button

again and keep pressing.

1) Press MUTE button twice

on Remote Control.

2. DISPLAYINGTHE ADJUSTMENT MENU

Adjustment mode

Press

Service mode

Item

Data

1) Press MENU button on TV.

6. SELF DIAGNOSTIC FUNCTION

1) Press “9” button on Remote Control during display of adjustment menu in the service mode.

The diagnosis will begin to check if interface among IC’s is executed properly.

2) During diagnosis, the following displays are shown.

Part number of microprocessor (IC609)

Operation number of protection circuit (The number of times of the power supply OFF by fan stop). . . .“000” is normal.

BUS line check “OK” ................... Normal

“SCL-GND” or “NG” ........... SCL-GND short circuit

“SDA-GND” or “NG” ........... SDA-GND short circuit

“SCL-SDA” or “NG” ............ SCL-SDA short circuit

BUS line ACK (acknowledge) check

“OK” ................... Normal

Sync.signal check Green display..... Normal

Red display ........NG

MAIN ........ Main sync

SUB .......... Sub sync (when turn on the PIP)

ID code for TV Set

Version of "EEP"

Data for "OPT"

SELF CHECK

NO. 23 * * * * * *

POWER : 000

BUS LINE : OK

BUS CONT : OK

BLOCK : MAIN SUB

SET ID : 80

E2P VER : 08

OPT1 : 00 OPT2 : A0

SW VER : DLE May 13 2004 17:**:**

HDMI

NO ********

ERR CDDE : 00

BEP

SW VER : 42

E2R VER : 02

TIME

TV : ******

LAMP :

****

Thermo1 : +51

Thermo2 : +50

Temperature of DMD

Temperature of the color wheel neighborhood

Software version history

HDMI Software

NO ***** .....Serial No.

ERR CODE .....Error Code

BEP Software Version

SW VER : **.....Version

E2P VER: ** EEP ROM Version

Use time

TV .....TV set on time (hour)

LAMP.....LAMP set on time (hour)

(It may shift from TV set on time.)

7. LED indications

The green and red LED lights on the TV control touchpad

(on the lower right corner of the TV screen)

indicate the TV's current status, as follows:

. Green ON = Control touchpad being pressed.

. Red ON = Power ON.

. Green and/or Red blinking

(see table below for condition and solution).

MENUVOLUMECHANNELEXITTV/VIDEO POWER

Green indicator

Red indicator

Control touchpad on TV front

LED Indication

Red and Green turn off.

Red light solid and Green off.

Red and Green lights solid.

Green blinks at 1-second intervals;

Red off.

Green blinks at 0.3-second inter-

vals; Red lights solid.

Green lights solid and Red blinks

at 0.5-second intervals.

Green and Red blink at 1-second

intervals.

Red blinks at 0.5-second intervals;

Green off.

Red blinks at 1-second intervals;

Green off.

Red blinks three times;Green off.

Red and Green blink three times.

Condition

Power supply OFF.(AC)

Power supply OFF. (Standby)

(North America)

Power supply ON.

Touched the touchpad

Lamp LPS mode

The lamp is not working properly.

The lamp unit door is not seated

properly. (U)

The lamp is not working properly

after the third automatic reset (see

item #7). (U)

FAN (Light engine unit) has

stopped.

BUS line is damaged

The color wheel has stopped.

Temperature rises abnormally.

(U) is restoration by the user.

Solution

The TV automatically will try to reset itself

three times.

Turn the POWER OFF and unplug the power

cord. Review “How to replace the lamp unit”

on pages 12-14 to ensure that the lamp unit

door is installed securely.

Turn the POWER OFF and then ON again.If

the problem persists, replace the lamp unit

(see pages 12-14).

• Is the output voltage of the supply voltage

regulator for the FAN in the power circuit

normal?

• Has dust accumulated in the FAN?

If the output voltage is not abnormal,

replace the faulty FAN with a new one.

• Check the faulty device through the self

diagnostics function under SERVICE mode.

• Does BUS line (SCL, SDA) work normally?

If the BUS line is under abnormal

conditions, replace the faulty device with

a new one.

• Is the output voltage of the power supply

circuit normal?

If the output voltage is normal, replace the

engine with a new one.

• Is the ventilating hole in the set (exhaust

slot on the rear) blocked or covered?

• Is FAN rotating normally?

• Has dust accumulated in the ventilating

hole?

If no abnormally conditions are found,

replace the engine with a new one.

SETTING & ADJUSTING DATA

CHAPTER 2 SPECIFIC INFORMATIONS

SERVICE MODE

ADJUSTING ITEMS AND DATA IN THE SERVICE MODE:

Item Name of adjustment Preset Data

Table-1

RCUT R CUT OFF

GCUT G CUTOFF

BCUT B CUT OFF

RDRV R DRIVE

GDRV G DRIVE

BDRV B DRIVE

BRTC BRIGHT CENTER

SCNT

SUB CONTRAST FOR TV

COLC COLOR CENTER

UVTT BASE BAND TINT

CNTX SUB CONTRAST MAX

HPOS H-POSITION (PAL/DFS)

VPOS

V-POSITION DC SHIFT (PAL/DFS)

CWDH

COLOR WHEEL DELAY (HIGH)

CWDL

COLOR WHEEL DELAY (LOW)

DMDB DMD BIAS

OPT0 TV SET OPTION 1

Note:

The image system data of RCUT-CNTX is different by each image format.

The NTSC value is indicated in the table.

60H

64H

48H

53H

5FH

76H

20H

D0H

40H

7FH

00H

FAH

03H

00H 01H

A0H

40H

14H

03H

0FH

05H

14H

04H

23H

4AH

63H

6FH

73H

20H

91H

24H

73H

01H

B0H

Item Name of adjustment Preset Data

OPT1 TV SET OPTION 2

TVOP TV OPTION

PLLW0 PLL WAIT TIME

PLLW1 PLL WAIT TIME

PLLW2 PLL WAIT TIME

PLLW3 PLL WAIT TIME

PLLW4 PLL WAIT TIME

PLLW5 PLL WAIT TIME

V01 VOLUME (DATA)

V25 VOLUME (DATA)

V50 VOLUME (DATA)

V75 VOLUME (DATA)

V100 VOLUME (DATA)

MODH MODUS DATA HIGH

MODL MODUS DATA LOW

PRES FMAM PRESCALE

SCTH

VOLUME SCART OPTION HIGH

SCTL

VOLUME SCART OPTION LOW

LOCATION OF CONTROLS

Front

Remote control sensor

(Behind the screen)

VIDEO 3

Vid

/audio inputs

TV/VIDEO

EXIT zyx •

POWER

Push to o

en.

MENUVOLUMECHANNELEXITTV/VIDEO POWER

* Green ON = Touchpad key being pressed;

Red ON = Power ON.

See page 64 for additional LED indications.

Channel zy

Volume x• Green and Red

LED indicators*

Side

Control touchpad on TV front (Gently touch the printed keys.)

ANT-2

IN ANT-1

ANT OUTAUDIO

VIDEO

Vid

/audio inputs

Push to open.

Back

HDMI IN

ANT-2

IN ANT-1

VIDEO 1/2

ColorStream

HD-1/HD-2

Video/Audio OUT

ANT OUTAUDIO

Variable

Audio OUT

120 VAC

60 Hz

Back

Front

Remote Control

POWER turns the TV on and off.

Press POWER to turn the TV on. The Red LED indicator will

be illuminated. Press POWER again to turn the TV off.

Note:

If the Quick Restart feature is in OFF mode, it can take up to several seconds for

the picture to appear. See page 28 for details.

SLEEP allows access to the automatic TV shut-off function

LIGHT The first press of the LIGHT button lights the keypad and turns

on the Illumination mode. With the Illumination mode on,

pressing any other key lights the keypad for 5 seconds (10 seconds

if you’re in programming mode).

Subsequent presses of the LIGHT button toggle between turning

the Illumination mode on and off.

Channel Numbers (0-9, 100) allow direct access to channels

MODE cycles through the six device modes: TV, CABLE/SAT, VCR,

DVD, AUDIO1, and AUDIO2. The mode indicator light will

remain lit for a few seconds.

PIC SIZE cycles through the five pictures sizes: Natural, Theater Wide 1,

2, 3, and Full

FAVORITE allows access to the favorite channel search function

MENU allows access to on-screen programming menus

ENTER sets programming menu information

yz x • select or adjust programming menus

FAV yz cycles through favorite channels

CH yz cycles through programmed channels

VOL yz adjusts the volume level

EXIT exits the programming menus

INPUT selects the video input source

MUTE mutes the sound

RECALL displays on-screen information

CH RTN returns to the last viewed channels

POP CH yz selects the POP (picture-out-picture) channel

SPLIT turns the POP feature on and off

CH SCAN

allows access to the programmed channel search functionx

FREEZE freezes the picture. Press again to restore the picture.

SWAP switches the main and POP pictures

POP DIRECT CH allows direct access to POP channels

SOURCE selects the POP picture source

Note:

The error message “Not Available” will appear

if you press a key for a function that is not

available.

PROGRAMMING CHANNEL MEMORY

Adding channels to the TV’s memory

When you press Channel yor z, your TV will stop only on the

channels stored in the TV’s channel memory.

Follow the steps below and on the next page to program all active

channels into the TV’s memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and

store them in its memory. After the channels are stored automatically,

you can manually add or erase individual channels.

To program channels automatically:

1. Press MENU, and then press xor •until the SET UP menu

appears.

2. Press yor zuntil TV/CABLE is highlighted, and then press

ENTER to display the pull-down menu.

3. Press yor zto highlight either TV or CABLE, depending on

which you use. If you use an antenna, highlight TV; if you use

cable channels, highlight CABLE.

LANGUAGE SET UP

CLOCK SET TV

CABLE

ANT 1 / 2

TV / CABLE

CH PROGRAM

ADD / ERASE

SELECT::

SETENTER

4. Press ENTER.

5. Press zto select CH PROGRAM.

LANGUAGE SET UP

CLOCK SET 00:00

ENGLISH

ANT 1 / 2 ANT1

TV / CABLE CABLE

ADD

CH PROGRAM

ADD / ERASE

MOVE::

START

ENTER

6. Press ENTER to start channel programming. The TV will

automatically cycle through all the TV or Cable channels

(depending on which you selected), and store all active channels

in the channel memory.

While the TV is cycling through the channels, the message

“Programming Now—Please Wait” appears.

7. When channel programming is complete, the message

“Completed” appears.

8. Press Channel yor zto view the programmed channels.

123

456

789

100/

ENT

POWER

+10

ACTION

MODE

PIC SIZE

LIGHT SLEEP

ENTER

FAV

CH VOL

EXIT

CH RTN

DVD RTN

DVD CLEAR

SLOW/DIR

SKIP/SEARCH

INPUT

RECALL

MUTE

FAV

CABLE/SAT

VCR

DVD

AUDIO1

AUDIO2

yzx •

Channel yz

Note:

To tune the TV to a channel not programmed

in the channel memory, you must use the

Channel Number buttons on the remote

control.

ENTER

Andere Handbücher für 52HMX84 - Cinema Series HD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Projektionsfernsehen Handbücher

Toshiba

Toshiba TheaterWide 56HM66 Bedienungsanleitung

Toshiba

Toshiba ColorStream TP50G60 Bedienungsanleitung

Toshiba

Toshiba TP50F50 Bedienungsanleitung

Toshiba

Toshiba 42HM66 - 42" Rear Projection TV Bedienungsanleitung

Toshiba

Toshiba TheaterWide 52HMX94 Bedienungsanleitung

Toshiba

Toshiba TheaterWide 46H83 Bedienungsanleitung

Toshiba

Toshiba 50HMX96 - 50" Rear Projection TV Bedienungsanleitung

Toshiba

Toshiba TP48D90 Bedienungsanleitung

Toshiba

Toshiba 50HDX82 Bedienungsanleitung

Toshiba

Toshiba TP48E60 Bedienungsanleitung

Toshiba

Toshiba TheaterWide 56HM195 Bedienungsanleitung

Toshiba

Toshiba 52HM85 Bedienungsanleitung

Toshiba

Toshiba 46HM94P Bedienungsanleitung

Toshiba

Toshiba 62HM14 Bedienungsanleitung

Toshiba

Toshiba TP48C90 Bedienungsanleitung

Toshiba

Toshiba 50A50 Bedienungsanleitung

Toshiba

Toshiba TheaterWide 62HM15 Bedienungsanleitung

Toshiba

Toshiba TW56D90 Bedienungsanleitung

Toshiba

Toshiba ColorStream TP50G90 Bedienungsanleitung

Toshiba

Toshiba TheaterWide 62HM15 Bedienungsanleitung

Toshiba

Toshiba 51H85C Bedienungsanleitung

Toshiba

Toshiba TP50G50 Bedienungsanleitung

Toshiba

Toshiba TheaterWide 52HMX94 Bedienungsanleitung

Toshiba

Toshiba TZ43V61 Bedienungsanleitung

Beliebte Projektionsfernsehen Handbücher anderer Marken

Samsung

Samsung ST-43T6P Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric WD-65734 Bedienungsanleitung

Optoma

Optoma EP652A Bedienungsanleitung

Samsung

Samsung SP43T8HPX/XEC Bedienungsanleitung

Philips

Philips 28PW6006 - annexe 1 Bedienungsanleitung

Sony

Sony KP-57WS500 - 57" Hi-scan 1080i™ 16:9 Projection... Benutzerhandbuch

Philips

Philips 43PP8421 Bedienungsanleitung

Hitachi

Hitachi 51F510 Bedienungsanleitung

RCA

RCA P52950 Bedienungsanleitung

Sony

Sony KP-51DS1U Bedienungsanleitung

Magnavox

Magnavox 51MP392H - 51" Widescreen Hd Ready Tv Bedienungsanleitung

Hitachi

Hitachi 46F510 Bedienungsanleitung

Pioneer

Pioneer Elite PRO 510HD Bedienungsanleitung

Philips

Philips 43PP8421 Handbuch

JVC

JVC I'Art Pro AV-48P776 Bedienungsanleitung

Sony

Sony GRAND WEGA KDF-55XS955 Bedienungsanleitung

Sony

Sony KP-46WT520 - Wide Screen Projection Tv Bedienungsanleitung

Philips

Philips 50PL9200D Bedienungsanleitung