Toshiba RSAP Service-Handbuch

TOSHIBA International Corp

REMOTE STATUS ALARM PANEL

RSAP

INSTALLATION/INSTRUCTION MANUAL

Table of Contents

Physical Characteristics…………………………………………….… 3

Installation Instructions……………………………………………….. 3

Operating Instructions…………………………………………………. 4

Remote Monitor Closed (Figure 1.0)………………………………… 5

Remote Monitor Closed Hardwire (Figure 1.1)…………………….. 6

Terminal Block Description (Figure 2.0)……………………………. 7

Terminal Block Description (Figure 2.1)…………………………..…8

Remote Monitor Open (Figure 3.0)…………………………………... 9

Remote Monitor Open Hardwired (Figure 3.1)………………….... 10

Remote Monitor Conduit Access (Figure 4.0)……………………. 11

Figure G8000…………………………………………………………… 12

Figure 4200FA 15-50Kva...…………………………………………… 13

Figure 4200FA 80kVA…….…………………………………………....14

Physical Characteristics

Weight: 10lbs

Height: 8 inches

Width: 8 inches

Depth: 4.8 inches

Installation

1. Locate the area where the Remote Status Alarm Panel (RSAP) will be installed.

The monitor should be within 1000 feet from the UPS.

2. Mount the monitor to the wall using the four pre-drilled holes in the back. Use

appropriate hardware for the installation.

3. Wiring requirements are: 7 twisted pair 16 AWG cable run in metal conduit.

Preferred use of Belden Catalog No. 1485 (8 twisted pair) or equivalent. All

electrical and mechanical connections to be made per local and /or national

electric codes.

4. Connect the conduit to the RSAP by punching the appropriately sized hole in a

convenient location.

5. Referring to Figure 2.0, 3.0 and the corresponding UPS wiring diagram, connect

the seven (7) pairs of twisted wire from the RSAP to the customer accessible

alarm contact terminal bar in the UPS module. (Refer to UPS manual for location)

6. Referring to Figure 3.0, install (6) AA batteries. Batteries will provide about

eight (8) hours of run time in the event of an AC power failure. Replace these

batteries yearly for optimum performance.

7. Referring to Figure 1.0, connect the power supply adapter into the corresponding

jack located on the bottom left-hand side of the RSAP enclosure. Plug the power

supply into a convenient 120V/60Hz wall receptacle. Failure to connect to a

suitable wall outlet will drain the RSAP’s internal batteries and/or result in

damage to the monitor. (If supplied with the hardwire version, please refer to

Figure 3.1 for AC input terminal block layout. Connect L1, Neutral, and Ground

with minimum of 18AWG wire.)

*The RSAP must be installed by a qualified electrician. Installation to be inspected by an

Authorized TIC trained Service Engineer at the time of startup.

Operating Instructions

ALARM SILENCE pushbutton is used to silence the alarm.

MONITOR RESET pushbutton is used to reset the RSAP UPS FAULT alarm. The monitor will

alarm again if the alarm condition is still present following the RESET.

Monitor TEST pushbutton is used to check the operation of all LED’s and the audible alarm. All

LED’s that are illuminated will go off and all lights that are off will illuminate. Horn will also

sound.

INTERNAL MONITOR BATTERY TEST button is used to test the condition of the monitor’s

battery pack. If the yellow LED does not illuminate, replace the batteries.

Reset the RSAP as follows:

1. On the UPS, note the alarm and its fault code. If applicable, contact 24 hour UPS field

service at (877) 867-8773.

2. If no alarm code is present, press the monitor reset button.

3. If the monitor’s audible alarm sounds again repeat steps 1 and 2.

4. Contact TIC service if the alarm cannot be reset after a few attempts.

Refer to Figure 1.0 for location of the LED’s and pushbuttons described below:

1. Rectifier / Charger LED. This green LED is illuminated as long as the UPS inverter is

operating.

2. Battery LED. This yellow LED is illuminated as long as the UPS is in the battery backup

mode. The audible alarm will beep intermittently.

3. Inverter On LED. The green LED is illuminated as long as the UPS inverter is operating.

4. Output LED. This green LED is illuminated as long as there is power to the critical load.

(Either by the Inverter or Bypass)

5. Load On Bypass LED. This yellow LED is illuminated as long as the critical load is

6. AC Input LED. This green LED is illuminated as long as there is AC power supplied to

the system.

7. UPS Fault. This red LED is illuminated and the audible alarm sounds when a UPS fault

has occurred. The RSAP must be reset after the alarm is cleared.

8. Overload LED. This red LED is illuminated when a UPS overload has occurred. The

audible alarm will also sound.

9. Input Failure LED. This red LED is illuminated when an input power failure condition is

present. The audible alarm will also sound.

10. Battery Low Voltage. This red LED is illuminated as soon as the DC bus voltage

approaches its cutoff voltage. The audible will also sound.

11. Alarm Silence LED. This red LED will illuminate when the ALARM SILENCE

pushbutton has been pressed and alarm condition is still present. If alarm condition clears,

the ALARM SILENCE LED will automatically reset.

12. Internal Monitor Battery OK LED. This yellow LED will illuminate when its

corresponding push button is pressed and the batteries are OK. IF this light is dim or does

not light, replace all internal batteries.

BYPASS

INPUT

OUTPUT

UPS FAULT

OVERLOAD

INPUT FAILURE

BATTERY LOW VOLTAGE

ALARM SILIENCE

INTERNAL MONITOR BATTERY OK

MONITOR RESET

MONITOR TEST

ALARM SILENCE

INTERNAL MONITOR

BATTERY TEST

INPUT

BATTERY

LEGEND

GREEN-NORMAL STATE

AMBER-ABNORMAL STATE

RED-FAILURE STATE

1. RECTIFIER ON (GREEN LED)

11. ALARM SILENCE (RED LED)

2. BATTERIES ON (YELLOW LED)

3. INVERTER ON (GREEN LED)

4. OUTPUT TO CRITICAL LOAD (GREEN LED)

5. LOAD ON BYPASS (YELLOW LED)

12. INTERNAL MONITOR BATTERY OK (YELLOW

LED)

10. BATTERY LOW VOLTAGE (RED LED)

9. INPUT FAILURE (RED LED)

8. OVERLOAD (RED LED)

7. UPS FAULT (RED LED)

6. AC INPUT ON (GREEN LED)

AUDIBLE ALARM

MONITOR RESET PUSHBUTTON

MONITOR TEST PUSHBUTTON

ALARM SILENCE PUSHBUTTON

INTERNAL MONITOR BATTERY TEST

PUSHBUTTON

FIGURE 1.1

(INTERNAL POWER SUPPLY / HARDWIRE OPTION)

1 AC Input L1 (option)

2 AC Input L2 (option)

5 BYPASS

6 BYPASS COMMON

7 INVERTER

8 INVERTER COMMON

9 ON BATTERIES

10 ON BATTERY COMMON

11 RECTIFIER

12 RECTIFIER COMMON

13 UPS FAILURE

14 UPS COMMON

15 LOW BATTERY

16 LOW BATTERY COMMON

17 OVERLOAD

18 OVERLOAD COMMON

TERMINAL BLOCK DESCRIPTION

(LOCATED INSIDE BOX)

FIGURE 2.1

(INTERNAL POWER SUPPLY / HARDWIRE OPTION)

TB 1

3 BYPASS

4 BYPASS

Andere Toshiba Sicherheitssystem Handbücher

Toshiba

Toshiba Symbio Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung