Toshiba MK1234 Kurzanleitung

2.5” Hard Disk Drive Installation Notes - P/N 480070-B0 P/N 480070-B0 2.5” Hard Disk Drive Installation Notes -

MK1234/1034/8034/6034/4034GSX 05/06 05/06 MK1234/1034/8034/6034/4034GSX

PIN ASSIGNMENT

The following table describes all of the pins on the Serial ATA connector

Signal Segment Key

S1 GND 2nd mate

S2 A+ Differential Pair A from PHY

Signal S3 A-

Segment S4 GND

S5 B- Differential Pair B from PHY

S6 B+

S7 GND 2nd mate

Signal Segment “L”

Central Connector Polarizer

Power Segment “L”

P1 V33 3.3V Power (unused)

P2 V33 3.3V power (unused)

P3 V33 3.3V Power pre-charge 2nd mate (unused)

P4 GND

P5 GND

P6 GND

P7 V5 5V Power pre-charge 2nd mate

P8 V5 5V power

P9 V5 5V power

P10 GND

P11 ACT/Spin

P12 GND 1st Mate

P13 V12 12V Power pre-charge 2nd mate (unused)

P14 V12 12V Power (unused)

P15 V12 12V Power (unused)

Power segment Key

Notice: this drive uses 4V power only. 3.3V and 12V power are not used.

TECHNICAL SUPPORT

Should you require technical support, contact your computer distributor. If your dis-

tributor is unable to answer your questions, have them call Toshiba Storage Device

Division Technical Support, on your behalf.

TOSHIBA - STORAGE DEVICE DIVISON TECHNICAL SUPPORT

PHONE: 510/651-6798 FAX: 510/623-9893

EMAIL: [email protected]

You can also visit Toshiba’s web site at: http://www.sdd.toshiba.com

TOSHIBA STORAGE DEVICE DIVISION

2.5" HDD INSTALLATION NOTES

MK1234/1034/8034/6034/4034GSX

Contents subject to change without prior notice.

GENERAL DESCRIPTION

Toshiba’s 9.5mm series of 2.5" Hard Disk Drives is comprised of fast, high-capacity

drives which feature an ATA-7 and Seria ATA 1.0a/Seria TATA II 1.2 interface embedded

controller. Toshiba recommends that these drives be installed by a qualified technician.

Additional installation hardware may be required depending on how and or where the

drive is being installed.

Specifications MK1234GSX MK1034GSX MK8034GSX

HDD2D31 HDD2D37 HDD2D38

Formatted Capacity 120.034GB 100.03GB 80.026GB

Height 9.5mm 9.5mm 9.5mm

# of Disks (platters) 2 2 2

# of Data Heads 4 4 3

MK6034GSX MK4034GSX

HDD2D35 HDD2D39

Formatted Capacity 60.012GB 40.008GB

Height 9.5mm 9.5mm

# of Disks (platters) 1 1

# of Data Heads 2 2

FUNCTIONAL SPECIFICATION

Logical Drive MK1234GSX MK1034GSX MK8034GSX

Parameters HDD2D31 HDD2D37 HDD2D38

# of Cylinders (user) 79,056 69,336 74,520

Bytes per Sector 512 512 512

LBA Sectors 234,441,648 195,371,568 156,301,488

Buffer Size (KBYTES) 8,192 8,192

Rotation Speed (±.1%) 5400 5400

Transfer Rate 245 – 475 220 – 466 220 – 466

Internal (MBITS/sec.)

# of Cylinders (logical) 16,383 16,383 16,383

# of Heads 16 16 16

# of sec./Track 63 63 63

Host Transfer Rate 150MB/s 150MB/s 150MB/s

Seek Time (MSEC.)

Average 12 12 12

Track-to-track 2 2 2

Maximum 22 22 22

2.5” Hard Disk Drive Installation Notes - P/N 480070-B0 P/N 480070-B0 2.5” Hard Disk Drive Installation Notes -

MK1234/1034/8034/6034/4034GSX 05/06 05/06 MK1234/1034/8034/6034/4034GSX

Logical Drive MK6034GSX MK4034GSX

Parameters HDD2D35 HDD2D39

# of Cylinders (user) 79,056 60,912

Bytes per Sector 512 512

LBA Sectors 117,210,240 78,140,160

Buffer Size (KBYTES) 8,192 8,192

Rotation Speed (±.1%) 5400 5400

Transfer Rate 245 – 475 199– 434

Internal (MBITS/sec.)

# of Cylinders (logical) 16,383 16,383

# of Heads 16 16

# of sec./Track 63 63

Host Transfer Rate 150MB/s 150MB/s

Seek Time (MSEC.)

Average 12 12

Track-to-track 2 2

Maximum 22 22

UNPACKING PROCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage to

the container or its contents (the carrier is responsible for any damage incurred during

shipment). The drive is a precision device and even a small drop onto any surface can

cause damage. Prior to opening the anti-static bag, it is recommended that the user

ground themself with a ground strap or by touching the PC chassis or other metal object.

Remove the drive from the anti-static bag and check it for damage. Place the drive on the

anti-static bag while configuring jumpers to avoid any electrostatic discharge. Save the

shipping container and packing material for possible use later.

INSTALLATION INSTRUCTIONS

Note: Toshiba’s 2.5” HDDs are primarily used in notebook devices. Installation into

a notebook varies depending on the system manufacturer. Toshiba’s 2.5” drives that

are installed into a desktop PC require a 3.5” installation kit.

1. Determine mounting configuration (can be mounted in either a horizontal or ver-

tical orientation).

2. Configure drive for system application.

3. When connecting the drive and host system with Serial ATA cable, use of a Serial

ATA 1.a specification compliant cable is recommended.

4. Refer to applicable manuals for software installation instructions.

Single Segment S1

Power Segment P1

Factory use

FIGURE 1 – 2.5" HDD JUMPER LOCATIONS

FIGURE 2 – MOUNTING HOLE LOCATIONS

INTERFACE CONNECTOR

Drive Side Connector Molex RSD97799-015 or equivalent

for board Right Angle Type: Molex 67492-0221,

67492-0222 or equivalent

for cable Molex 88750-5318 or equivalent (for

signal). No recommendation now for power

segment.

Recommended

Host Side

Connector