Totai 16/DK1023A Bedienungsanleitung

For Outdoor Use Only

Important: Read these instructions for use carefully so as to familiarise yourself with

the appliance before connecting it to its gas container. It is also important to follow the

assembly instructions. Keep these instructions for future reference

Model: 16/DK1023A

LPGSASA PERMIT NUMBER 1051-XX-RSA-12-A

INSTRUCTIONS FOR USE AND ASSEMBLY

Parts List:

Reﬂector

Flame Screen

Glass Tube

Protective Guard

NOITPIRCSED TRAP QUANTITY

Flame Screen

Control Box Assy

Lower Support

Block Belt

Wheel Assembly

Bottom Plate

NOITPIRCSED TRAP QUANTITY

Reﬂector

B 1

Glass Tube

Upper Support

Black Silicone Ring

Protective Guard

Side Panel

Front Panel

Upper Support

Black Silicone Ring

Side Panel

Front Panel

Block Belt L

Lower Support K

Control Box Assy J

Wheel Assembly M

Bottom Plate N

Please check parts against the list below before assembling your Flame Heater. Take a few moments

to familiarise yourself with the contents. Check that all holes are clear of paint before assembly

ASSEMBLY PARTS - 1

HARDWARE CONTENTS (shown actual size)

Wing nut

Qty. 3

Small ﬂat

washer Φ6

Qt . 6

3/16” Screw

Qty. 42

Philips

screwdriver

Qty. 1

Bolt M6 X 12

Qty. 4

Wrench

Qt . 1

Fixing Bracket

Qty. 4

Stud

Qty. 3

Flange

nut

Qty. 4

Screw

M5 X 12

Qty. 6

Knob

Qty. 1

Screw

M4 X 10

Qty.1

Chain

Qty.1

Long Stem Lighter

Qty.1

ASSEMBLY PARTS - 2

Assembly Instructions

For Best Results:

First please prepare for tools needed such as:

Rubber Hammer Wrench Phillips-head Screwdriver Flat-head Screwdriver

Then remove all contents from packaging, and make sure all parts are present before

attempting to assemble! Tighten all bolt connections by hand ﬁrst, then when the ﬂame

heater is fully assembled, go back and tighten.

Before Assembly:

Please read all instructions thoroughly before proceeding. Find a large, clean area in

which to assemble your ﬂame heater. Please refer to the parts list and assembly diagrams

as necessary.

Assembly of the ﬂame heater involves many large components, it is advisable to have

two people assemble the unit.

Whilst every effort has been made in the manufactur e of your barbecue to remove

any sharp edge, you should handle all components with care to avoid accidental

injury.

Tools required: Either a Philips crosshead or ﬂat-bladed screwdriver and either an

adjustable spanner or a pair of pliers.

ASSEMBLY PROCEDURES

Hardware Used

1. Assemble the wheel assembly to the

bottom plate. Fix the wheel assembly to the

bottom plate using 4pcs bolt M6X12 and 4pcs

ﬂange nut M6.

2. Insert the pins of the base to the holes of

lower support, press to secure the pins. Using

4pcs screw M5x12 to secure the lower support

and base.

Insert the pins of the control box assy to the

holes of upper support, press to secure the

pins. Using 4pcs screw 3/16” screw to secure

the upper support and control box assy.

x 4

Wrench x 1

x 4

Philips

screwdriver x 1

Bolt M6 X 12

M6 Flange nut

Screw M5 X 12

DD x 4

3/16” Screw

Hardware Used

3.Assemble block belt.

Fix the block belt to the 2pcs of lower support

behind the front door,using 2pcs screw M5X12.

4. Assemble the middle support.

Insert the 4pcs upper support to the lower

support. Secure them with 8pcs screw 3/16”.

x 1

Philips

screwdriver

x 8

x 1

Philips

screwdriver

3/16” Screw

GG x 2

Screw M5 X 12

Hardware Used

5. Assebmle the ﬂame screen to the upper

support.

Secure the ﬂame screen to the upper support

using 8pcs screw 3/16”.

6. Assemble the reﬂector onto the ﬂame

screen.

Screw the 3pcs stud on the ﬂame screen,

put 3pcs washer Φ6 onto the top of stud,

then put the reﬂector onto the stud, secure

them with 3pcs washer Φ6 and 3pcs wing

nut.

x 3

x 6

Hardware Used

x 8

Philips

screwdriver

3/16” Screw

x 1

Wing nut

Washer Φ6

CC Stud

7. Carefully install the glass tube by lifting up

and inserting through the center hole in the

upper plate. Ensure the black silicone ring is

attached to the lower edge of the glass tube

as illustrated. Slide the glass tube through the

hole of the lower plate cover and onto the

middle plate. Check and ensure that the glass

tube is positioned properly and is completely

covering the center hole of the middle plate.

8. Assembly the protective guard.

Hang the hooks of the protective guard onto

the holes in supports.

Secure the protective guards with ﬁxing

brackets with 4pcs 3/16" screws.

WARNING! The black

silicone ring must be in place

prior to operating the heater.

To aid in installation

place black silicone

ring on the middle

plate and then

install glass tube.

Ensure the rim of

the glass tube sits

ﬁrmly in the black

silicone ring.

BLACK SILICONE

RING

Hardware Used

x 4

Philips

screwdriver

3/16” Screw

x 1

HH Fixing

Bracket x 4

11. LPG Hose Connection.

WARNING! Ensure the hose does not contact

any high temperature surfaces, or it may melt

and leak causing a ﬁre.

After the cylinder is placed inside the heater, secure

the cylinder with block belt tightly.

12. Leak Check.

Regulator / Cylinder

connection

Hose / Regulator

connection

WARNING!

A leak test must be performed annually and each time a cylinder is connectd or if a part

of the gas system is replaced.

WARNING! Never use an open ﬂame to check for gas leaks. Be certain no sparks or open ﬂames are

in the area while you check for leaks. Sparks or open ﬂames will result in a ﬁre or explosion, damage to

property, serious bodily injury, or death.

Leak testing: This must be done before initial use, annually,and whenever any gas components are replaced

or serviced. Do not smoke while performing this test, and remove all sources of igniion. See Leak Tesing

Diagram for areas to check. Turn all burner controls to the oﬀ posiion. Turn gas supply valve on.

Brush a half-and-half soluion of liquid soap and water onto all joints and connecions

of the regulator, hose, manifolds and valves.

Bubbles will indicate a gas leak. Either ighten the loose joint or have the part replaced with one recommended

by the Customer Care department and have the patio heater inspected by a qualiﬁed gas technician.

If the leak cannot be stopped, immediately shut oﬀ the gas supply, disconnect the cylinder , and have the patio

inspected by a ceriﬁed gas installer or dealer. Do not use the patio heater until the leak has been corrected.

PRECAUTIONS

APPLIANCE STAND AND LOCATION

BURN-BACK (FIRE IN BURNER TUBE OR CHAMBER)

In the event of a burn-back, where the ﬂame burns back to the jet,

immediately turn off the gas supply at the control valve on the panel.

After ensuring the ﬂame is extinguished, re-light the appliance in the

normal manner. Should the appliance again burn back, close the

control valve and call a service technician. Do not use the appliance

again until the service technician has declared that it is safe to do so.

Installation and services should only be a done qualiﬁed person.

Do not use the heater in an explosive atmosphere.

Before use, check the hose.

Disconnect LPG cylinder before moving the heater.

Do not attempt to alter any parts of the heater.

Example: Using the heater without reﬂector or protection guard.

The appliance shall not be used in basements or below ground level.

It must always be placed on a solid and level surface.

Never replace or substitute the regulator use only that one is suitable both appliance category and normal gas

pressure

The LPG gas cylinder valve should be turned off when the heater is not in use.

Don't not use the heater when it is raining, and do not let any liquid splash to the glass tube when the heater is

Do not paint protection guard, control box or reﬂector.

Keep the children away from the heater, always be carefully not to knock down the heater, which will break the

glass tube and might cause injury.

Do not move the appliance when in operation.

After a long break of operation, the gas parts in the control box of the heater and the hose should be inspected

for spiders, spider webs or other insects.

Check the heater immediately if any of the following exists:

1. There is smell of gas.

2. The heater is not enough effective.

3. The burner makes popping noise during use (a slight popping noise is normal when the burner is

extinguished

after use).

If you smell gas, turn off the valve immediately. If smell persists, contact the dealer or gas supplier immediately.

The hose with regulator assembly shall be stored in a safe place to avoid it’s accidental damage.

Children and adults should be aware of the high surface temperature hazard, and should keep a safe distance

away to avoid clothes burning or igniting.

Young children should be carefully supervised when they are in the working area of the heater.

Clothing or other ﬂammable material should not be hung from the heater, or placed on or near the heater.

Do not obstruct the ﬂow of combustion products.

Keep the ventilation opening of the cylinder enclosure free and clear of debris.

Do not obstruct the ventilation holes of the cylinder housing.

Shut off the valve of gas cylinder or the regulator before moving the appliance.

The tubing or the ﬂexible hose must be changed within the prescribed intervals.

Use only the type of gas and the type of cylinder speciﬁed by the manufacturer.

In case of violent wind particular attention must be taken against tilting of the appliance.

The appliance is for outdoor use only. Do not use

indoors or in an enclosed area.

Always maintain proper clearance from combustible

materials, i.e. top 800mm and sides 650mm minimum

INSTALLATION

OPERATION:

PREPARATION:

WARNING:

Never use the heater while it is raining, the glass tube would break when it suddenly met water.

Always turn off the heater while there is a rain.

Never splash any liquid to the glass tube when the heater is working

The glass tube will be extremely hot when it is working, never try to touch it and keep the children away

from the heater.

Always ensure the heater stands ﬁrmly, the glass tube may break if the heater was falls down onto ground.

Never use the heater if the glass tube has any cracks

Important safety requirements:

THIS APPLIANCE OUTDOOR USE ONLY

1. This appliance shall not be installed or used indoors, in buildings, garages or any other enclosed area.

2. DO NOT place articles on or against this appliance.

3. DO NOT use or store ﬂammable materials near this appliance.

4. DO NOT operate this appliance unless it is fully assembled with reﬂector and protection guard in place.

5. Installation and repair should be done by a qualiﬁed service person. The appliance must be inspected

before use and at least annually by a qualiﬁed service person. More frequent cleaning may be required as

necessary. It is imperative that control compartment, burners and circulating air passages of the heater

and light be kept clean.

You will need to purchase an LPG cylinder

You need a suitable size LPG cylinder that can be installed to the

compartment.

You have to use pressure regulator with an outlet pressure complying

with the appliance category. The ﬂexible tube must be approved also.

Connect the hose to the hose connector in the control box

Warning: Always test the hose for leaks with soapy water at both ends.

To Turn On The Heater

1. Open the cylinder control valve 1½ turns in an anti clockwise direction

2. Press and turn the variable control knob on the heater to the PILOT position (90 in an anti- clockwise

direction.

3. Whilst in the Pilot position press in the variable control knob and hold in that position for 30 secs. Whilst

holding the knob in the pressed in position press the ignitor button several times until the pilot ﬂame ignites.

Note:

ŸIf a new cylinder has just been connected to the heater please allow 60 seconds for the air in the gas

hose to purge out of the pilot jet before pressing the ignitor button.

ŸIt is important to hold in the control knob when pressing the ignitor button.

ŸIf the plot ﬂame does not ignite repeat step 3 above.

4. After the pilot ﬂame ignites turn the variable control knob to the maximum position and leave in that position

for 5 mins. or more before turning the control knob to the desired temperature setting

To Turn off the Heater

1. Turn the variable control knob to the PILOT position.

2. Press and turn the variable control knob to the OFF position

3. Turn the cylinder control valve to the closed position in a clockwise direction.

lgnitor

Ignitor button Variable

Control knob

Inhaltsverzeichnis

Andere Totai Heizung Handbücher

Totai

Totai F6T40G2 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung