Totevision LCD-1700VRZ Bedienungsanleitung
Table of Content
Operating Instructions
Safety Precautions _________________________________ 2
Care and Maintenance ______________________________ 3
CHAPTER 1
Introduction_______________________________________ 4
Factory-Preset Modes _______________________________ 5
Specification
LCD-1700VRZ Specification _______________________ 6
CHAPTER 2
Installing the Monitor _______________________________ 8
Follow these steps to install the monitor ___________________ 8
Control Function
LCD-1700VRZ Control function ____________________ 9
CHAPTER 3
Adjusting the Monitor _______________________________ 11
VGA OSD Screen_________________________________ 12
Adjustment Icon___________________________________ 12
CHAPTER 4
Video Adjusting ____________________________________ 15
Video OSD Screen _________________________________ 15
Adjustment Icon___________________________________ 15
APPENDIX
Troubleshooting ___________________________________ 17
2
Safety Precautions
This monitor is manufactured and tested on the principle that the user’s
safety comes first. However, improper use or installation may not only
damage the monitor but endanger the user as well. As a safety
precaution, go over the following WARNINGS carefully before installation,
and keep this guide handy.
Warnings:
lThis monitor should be operated only at the correct power sources
indicated on the label at the rear end of the monitor. If you are unsure
of the power supply in your residence, consult your local dealer or
Electricity Supplier.
lDo not try to repair the monitor yourself, as it contains no
user-serviceable parts. The monitor should only be repaired by a
qualified technician.
lDo not remove the monitor cabinet. There are high-voltage parts
inside that may cause an electric shock even when the power cord
is disconnected.
lStop using the monitor if the cabinet is damaged. Have it checked by
a service technician.
lPut your monitor only in a clean, dry environment. Unplug the monitor
immediately if it gets wet, and consult your service technician.
lAlways unplug the monitor before cleaning it. Clean the cabinet with
a clean, dry cloth. Apply non-ammonia-based cleaner onto the cloth,
not directly onto the glass screen.
lKeep the monitor away from magnetic objects, motors, TV sets, and
transformers.
lDo not place heavy objects on the cable or power cord.
lFor PLUG CABLE EQUIPMENT, the socket outlet should be installed
near the equipment and should be easily accessible.
3
Care and Maintenance
Care
lAvoid exposing your monitor directly to sunlight or other heat
sources. Place your monitor away from the sun to reduce glare.
lPut your monitor in a well-ventilated area. Do not place anything
heavy on top of your monitor.
lMake certain that your monitor is installed in a clean and
moisture-free area.
lKeep your monitor away from magnets, motors, transformers,
speakers, and TV sets.
Safety Tips
lIf smoke, an abnormal noise or an odor comes out of your monitor,
switch off the power immediately and call our service center.
lNever remove the rear cover of your monitor cabinet. The display
unit inside contains high-voltage parts and may cause an electric
shock.
lNever try to repair the monitor yourself. Always call your service
center or a qualified technician to fix it.
Note: This user’s manual contains graphics and information that is for
reference purposes only and is subject to change without notice.
4
CHAPTER 1
Introduction
BEFORE INSTALLING YOUR MONITOR
Read this manual cover to cover.
PAY ATTENTION to all WARNING and CAUTIONS
DO NOT use computer components not recommend by the
manufacture
Do not attempt to service the monitor your self. If a problem
occurs, contact the manufacture's authorized service center
ABOUT YOUR MONITOR
This monitor is a microprocessor-controlled, color monitor that
uses a TFT LCD panel. The monitor conforms to EPA Energy
Star and VESA DPMS (Display Power Management Signaling)
power management standards.
RGB MODE
This monitor is equipped with a microprocessor that identifies
your computer 's video mode and allows user to adjust the setting.
VIDEO MODE
This monitor can accept the NTSC or PAL signal to display the video
screen automatically. It also implement the video screen on PC
function, we called PIP function. We alsoprovide one pair of BNC
in/out connector inside.
5
FACTORY-PRESET MODES
Table 1 shows standard video mode setting that has been
pre-adjusted at the factory for accurate video display. These setting
are stored in the monitor's memory
Table 1. Factory-Preset Modes
PC mode
Mode Resolution H-Freq.(KHz) V-Freq(Hz)
NEC 640x400 24.83 56.4
VGA 640x350
720x400
640x480
640x480
640x480
31.47
31.47
31.47
37.86
37.5
70
70
60
72
75
SVGA 800x600
800x600
800x600
800x600
35.16
37.88
48.08
46.87
56.3
60.3
72.2
75
XGA
1024x768
1024x768
1024x768
48.36
56.47
60
60
70
75
SXGA 1280x1024
1280x1024 63.98
80 60
75
Macintosh 640x480
832x624
1024x768
1024x768
35
49.7
48.78
60.241
66.7
74.55
60
74.927
Video Mode
NTSC 525 lines, 60 fields
PAL 625 lines, 50/60 fields
6
Specifications
lLCD-1700VRZ 17” LCD 1U Rack Display Monitor
Overall Dimension(HxWxD): 483 x 515 x 43 mm
Effective Display area(H/V): 337.92 x 270.34 mm
Display colors: 16M colors
Scan Frequencies:
Horizontal 31.47K to 80KHz
Vertical 60Hz to 75Hz
Number of Pixels: 1280x1024 pixels
Pixel pitch: 0.264x0.264 mm
Picture Tube: 17" TFT LCD panel
Power:
Input 110-240VAC(auto-sensing)
Frequency: 48-62Hz
Consumption 45Watts maximum (on)
3 Watts (Power saving off mode)
PC RGB Connector: 15pin Mini D-sub (Standard)
Audio connector1 x stereo input
Speaker 2W x 2
RGB Signals:
Video Analog RGB 0.7Vp-p/75Ω
Sync Separate
Display Data Channel:
Compatibility VESA DDC 1/2B
Video connector input
S-connector x 1 (S-Video In)
AV connector x 3 ( one for video
Two for audio left/right)
Mini D type x 1 (for YcbCr/Component input)
BNC connector x 1 ( Composite Video In)
Video connector output
BNC connector x 1 ( Composite Video Out)
7
Operations:
User Controls On/Off Power Button,
+/-and Up/down keys
On Screen Display Auto adjustment, Brightness, contrast
color temperature, Hue, Tint,
Source select, PIP setup
H-position, V-position, OSD position
Audio volume, bass, treble, mute
Load default
Control Type: Digital
Compatibility: IBM and compatible, Apple
Macintosh, NEC
Environmental Limits:
Operating Temp 32°to 103°F ( 0°to 40°C )
Storage Temp. -4°to 140°F ( -20°to 60°C )
Operating Humidity 10 to 85% without Condensation
Storage Humidity 10 to 95% without Condensation
8
Chapter 2
PRODUCT PACKAGE
Open the shipping carton and check the contents. If any items are
missing or damaged, contact your dealer immediately.
The package should include the following items
lAnalog Color TFT LCD Monitor
lAccessory Box:
1. VGA cable x 1
2. AC to DC adapter x 1
3. Power Cord x 1
4. User’s manual/Warranty Card x 1
5. Audio cable x 1
6. Mini DIN/RCA cable (for Component Video In use)
INSTALLING THE MONITOR
The monitor is equipped with an auto sensing power supply for
voltage ranges from 110~240VAC, 60/50Hz. Confirm the line voltage
designation on the rear panel of the monitor.
Audio out
DC power Jack
DGB In
YcbCr Componen
t
S video
AV1
Audio R/L
BNC In
BNC out
9
CONTROL FUNCTIONS
The Monitor control functions are located on the right corner of the
front view side. They are shown in the figure below and described in
the following paragraphs.
The control key description
1. : Power Switch
2. -: Decrement
3. +: Increment or source select
4. ∇: Move to the next item
/ Brightness control
5. ∆: Move to the previous item
/ Brightness control
6. MENU : Activate the on screen display
function
Inhaltsverzeichnis
Andere Totevision Monitor Handbücher
Totevision
Totevision LCD-1500VB Bedienungsanleitung
Totevision
Totevision LCD-1048HDM Bedienungsanleitung
Totevision
Totevision LCD-1510V Bedienungsanleitung
Totevision
Totevision LCD-2002V Bedienungsanleitung
Totevision
Totevision LCD-643 Bedienungsanleitung
Totevision
Totevision LCD-800 Bedienungsanleitung
Totevision
Totevision LCD-5200HD Bedienungsanleitung
Totevision
Totevision LCD-1042TS Handbuch
Totevision
Totevision LCD-841D Bedienungsanleitung
Totevision
Totevision LCD-1048HD Bedienungsanleitung
Totevision
Totevision LCD-840D Bedienungsanleitung
Totevision
Totevision LCD-1044TC Bedienungsanleitung
Totevision
Totevision LCD-1042VB Bedienungsanleitung
Totevision
Totevision LCD-1700V Bedienungsanleitung
Totevision
Totevision LCD-642 Bedienungsanleitung
Totevision
Totevision LCD-2001VB Bedienungsanleitung
Totevision
Totevision LCD-2300HD Bedienungsanleitung
Totevision
Totevision LCD-703HD1 Bedienungsanleitung
Totevision
Totevision LCD-1411TC Bedienungsanleitung
Totevision
Totevision LCD-900HDT Bedienungsanleitung
