Component parts
Shower bar body 1 set
E bow pipe 1 part
Fixed shower head (round) 1 part
Wa ho der + fixing screws 1 set
In et hose (L= 500 ) 1 part
Shower hose (L= 1500) 1 part
Hand shower 1 part
Diverter va ve 1 set
Product Drawing
Installation and owner manual
To use the product effective y. Shou d fo ow the instructions of this manua .
Cuations be ore installation
1. Hot and co d water pressure during use.
Minimum pressure...................................0.05 MPa (f ow pressure)
Maximum pressure..................................0.75 MPa (static Pressure)
2. The hot water temperature shou d not exceed 65°C. It's recommended in the range of 60±5°C, hot water do not use stream
3. The ambient temperature shou d above 0°C, if not higher than 0°C, product wi be deformed, cracked and other damaged.
4. To prevent interna damage of shower, the water temperature of discharge side shou d not exceed 60°C. It's recommended
be ow 45°C.
5. Incase haven't used for ong time. It may be ead to interna and externa corrosion.
Installation Procedure
Figure 1
Figure 2
Ø6
Ho e Depth 35 mm
Anchor
Ho der Se f-tapping screw
(850)
Ho der
Fastening nut
Taper washer
Retaining wa b ocks
E bow pipe
Fixed
shower
head
Hand shower
Shower hose
Shower hanger
Diverter va ve
Ho der
Faucet
Water out
connector
Water in
connection
Lever hand e
Water out
fittings
Stain ess stee
hose (L=500mm)
Warning!
To prevent being sca ded due to ma function, make sure that the diverter va ve is switched to the hand shower position in order to
test the water temperature before using. Cannot a ow the diverter va ve switched underneath over head shower.
Care and Cleaning
Troubleshooting
Check Item
After insta ation, if there is ma functions occuring, p ease see be ow.
Unstab e se ection va ve
Vibration
Water eak
Problem
Less f ow rate
Fastening nut
(1. Have enough tight)
(3. Have enough tight)
(4. Have enough tight)
(7. Have enough tight)
Ho der
(2. Have enough tight)
Screw
Hex screw
(5. Have enough tight)
Fastening nut
(6. Have enough tight)
Ho der
Screw
(8. Have enough tight)
Hex screw
Your new product is designed for years of troub e-free performance.
1. Keep it ooking new by c eaning it periodica y with mi d soap, rinsing thorough y with warm water and drying with a c ean, soft c oth.
2. Do not use abrasive c eaners, stee woo or harsh chemica s, as these wi damage the product.
3. Do not use iquid c eaners with acid-base content. Incase of accidenta y happening, rinse with pure water immediate y in order to
prevent any damage of product surface.
Fai ure to fo ow these instructions may void your warranty.
Warranty
P ease find detai in warranty card as attached
Adjusting nut
200mm ift
Hand shower position
Fixed shower position
Figure 3 Figure 4
~
~
F ow Regu ator
(10.Dirt)
O-Rings
(11. Scratched)
Gasket rubber
(13. Scratched)
(14. Have enough tight)
Pressure spoo
(15. Have enough tight)
(16. Have enough tight)
Lever hand e
Fastening screw
Packing
(17. Scratched, dirt)
Packing
(9. Scratched, dirt)
O-rings
(12. Scratched)
10, 17
9, 11, 12, 13, 17
1, 2, 3, 4, 5, 6, 7, 8
14, 15, 16
Require adjust the height of the fixed shower
by adjusting the nut.
1. Installation wall mouting
2. Installation ixed shower head
3. Installation hand shower
4. Trial or tightening con irmatiom
5. Diverter Valve
