Toto RENESSE TSKT Montageanleitung

RENESSE

Thank you for your recent purchase

of the TOTO product . Please read

the enclosed information to ensure

the safe use of your product

Installation and Owner’s Manual

20.

•

™

0GU3034

TSKT

Important Safeguards----------------1

Specifications --------------------------2

Before Installation --------------------2

Set-up Drawing-------------------------3

Components ----------------------------3

Installation Procedure------------4~8

Before use ---------------------------8~9

Set-up Options -----------------------10

Replacement Parts ------------------10

Warranty---------------------------------11

SMA Thermostatic Mixing Valve

Contents

English Français

Español

(For your safety please follow the instructions below)

Warning

Do Not

Do not switch the hot and cold water supply lines. Do not

use steam for hot waer supply.

You may be scalded with hot water when you expect cold water.

Do not

disassemble

Read the “Important Safeguards” section thoroughly before installing the product.

Less

than185°F

(85°C)

Do Not

Caution

Do not use the product at temperature exceeding what local

codes allow.

If parts are damaged, property damage, scalding and other injuries may

occur.

Freezing

Important Safeguards

Warning

Caution

●The following symbols indicate safe and proper use of the

product. Failure to observe them may result in injury or property

damage. The symbols and their meanings are as follows.

●The following table demonstrates the use

of safety symbols in this manual.

Failure to observe this symbol may

result in serious injury.

Failure to observe this symbol may

result in injurty or property damage.

Absolutely Do NOT.

Do not disassemble

Mandatory!

Mandatory

Ah!

HOT

The valve should be calibrated by the installer so that water

temperature will be fixed 104˚F (40˚C) at the mark.

Scalding may occur if the temperature is not checked and valve is

not calibrated as necessary.

Do not use hot water supply that is higher than 185°F

(85°C). Do not use steam as hot water supply.

If water is hotter than 185°F is used. If it is broken, property damage,

scalding, and other injuries may occur.

Cold water

Hot

water

Stop

valve

Open

Filter

If you want to clean the filters, shut off the shut-off valve first

and do not open the caps abruptly.

If you don’t let hot water residue in the filter cool down for a while,

you may get burned while removing the filter from HOT side.

ENGLISH

Water Supply

Pressure

Minimum pressure

20 psi (0.15MPa)(flowing pressure)

125 psi (0.75MPa)(static)

Less than 185˚F (85˚C)

Water that meet National/Primary drinking water

regulation

34 - 104˚F (2〜40˚C)

1/2” NPT

Maximum pressure

Supplied Water Temperature

Water Quality

Ambient Temperature

Water Supply Connection

Flow Rate

Check local building

code

Depending on the model, some specifications may differ.

● If the water supply pressure is higher than 125psi (0.86MPa), you should buy a

reducing valve to reduce the pressure to the range of 0.2-0.3MPa (0.2-0.3MPa).

To use the faucet comfortably, the recommended pressure is about 30-45 psi

(0.2-0.3MPa).

●To prevent being scalded due to malfunction, the cold water supply pressure must

be higher than the hot water pressure, or you can make them equal. In addition,

if you increase the pressure of the hot water, it still must be lower than that of cold

water supply side.

●To prevent being scalded due to wrong operation, it is recommended the hot water

supply temperature is 140°F (60°C).

▪ Observe all local plumbing codes.

▪ Make sure water supply is shut off.

▪ Read these instructions carefully to ensure proper installation.

▪ Check to make sure you have the following parts indicated below.

●For ease of water flow adjustment and inspection with tools, you should prepare an

extra stop valve.

Specification

Before Installation

Please find in the package:

Installation &

Owner’s manual

Pipe Tape Adjustable Wrench Allen Wrech

Tools you will need for installation

Max. 2.5 gallons per minutes (9.5L/min)

ENGLISH

Check that you have the following parts.

*Some parts may differ from the figures depending on the model.

escutcheon

Cap Screw

handle

65 mm

6-5/16” (160 mm)

FINISHED

WALL

1/2” NPT

*Some parts may differ from the illustration depending on the model.

coverplate

nut

coverplate

gasket

coverplate

FINISHED

WALL

6-5/16” (160 mm)

2-9/16”

2-15/16” (75mm) MIN

3-9/16” (90mm) MAX

HOT

COLD

Thermostatic

Mixing Valve

Complete Shower Set

Set-Up Drawing

Components

Guard Cover

Upper limit

Lower limit

2-15/16” (75mm) MIN

3-9/16” (90mm) MAX

Thermostatic

Mixing

Valve Trim

(Sold

Separately)

4-15/16” (125 mm)

HOT to COLD supply

1/2” NPT

1-1/2”

(38 mm)

3-3/8”

(85 mm)

ENGLISH

Installation Procedure

Install and connect

valves with 1/2” pipe

Clean water supply

pipes by draining

Connect Hot/Cold

Water Supply Lines

Finish the wall.

Install

the Trims

Information below should be observed in order to properly install the shower.

Refer to the respective manual for

each item for Step 1 to Step 4.

7-7/8”

(200 mm)

15-3/4”

(410 mm)

39”

(1000 mm)

from the oor

44”

(1100 mm)

Location of

Showerhead

Location of

wall spout

Location of

Thermostatic

Mixing valve

Location of

Dual Volume

Control Valve

Location of

Single Volume

Control Valve

Location of

HandShower

Adapter

FLOOR

7-7/8”

(200 mm)

Showerhead

Wall Spout

1/2” pipe

Single Vol

Control

Valve

Dual Vol

Control

Valve

Hand Shower

Adapter

Thermostatic

Mixing Valve

Preparation Plumbing Setup

HOT

COLD

Showerhead

(Sold separately)

TS170A

(Sold separately)

Hand Shower Trim

(handshower and trim)

(TS170F

)

Bath Spout

(Sold separately)

TS170A

(TS170A

)

Dual Volume Control

Valve

(TSKD

)

Dual Volume Control

Valve

(TSKA

)

(Sold separately)

7-7/8”

(200 mm)

Thermostatic Mixing

Valve

(TSKT

)

Single Volume Control

Trim_Hand Shower

Dual Volume Control

Trim_Hand Shower

(TS170A

)

Thermostatic Mixing

Valve Trim

(TS170T

)

FLOOR

ENGLISH

1) Installation of the valve

(Rough-in and Connections)

FINISHED

WALL

Guard Cover

Lower limit

2-15/16” (75mm) MIN

3-9/16” (90mm) MAX

4-15/16” (125 mm)

HOT to COLD supply

Showerhead

Wall Spout

1/2” pipe

Single Vol

Control

Valve

Dual Vol

Control

Valve

Hand Shower

Adapter

Thermostatic

Mixing Valve

HOT

COLD

1) Confirm the rough-in provided and install the valve.

2) Depending on the Shower Setup Options (Refer to the Setup Options page), connect

all the valves (Thermostatic Mixing Valve, Volume Control Valve(s) and Handshower

Adapter (They all are sold

separately)).

Caution

Plug

Remove.

●

Perpare all tools and

plumbing accessories for

all the connections of the

Shower.

●

Be sure to use the pipe seal

for all pipe connections.

Do not lose the guard

cover.

Makeuse of it to confirm the

rough-in and to protect the

valve.

Remove the plug if wall

spout will be used.

If not, leave the outlet

plugged.

Thermostatic

Mixing Valve

●

Upper limit

Thermostatic

Mixing Valve

ENGLISH

2) Installation of the Valve (Water Supply Lines)

3) Before installation, dirt and debris in the Hot and Cold water supply lines

must be washed out entirely.

4) Connect the Hot and Cold Water Supply Lines.

Union

Thermostatic Mixing

valve

HOT water

supply

COLD water

supply

Elbow

Insulating

Material

4-15/16”

(125 mm)

1/2”

NPT

ԘInstall cold/hot water supply lines.

ԙConnect the union (provided in the package)

to Hot and Cold Water Supply Lines.

Caution

●

Attach both unions provided so

that supply lines will be at the

same level.

Wrap the insulating material

around the HOT water Supply

Pipe

GOOD BAD

ԚFasten the thermostatic mixing valve with the nuts of unions.

ԛAfter connecting the supply pipes, do the water test by running the water in

the Shower set and confirm that there is no leakage in all joints.

ENGLISH

3) Installation of the Valve

(Stem Adapter, Limiter Collar and Temperature Limiter)

Trim installation should not be begun until the

followings are confirmed:

1) Checking the water flow

2) Checking the filters

Caution

Stem Adjuster

Thermostatic

Mixing valve

Install the stem adapter into the valve as shown.

Finished Wall

Limiter Collar

1” (25 mm) MIN

1-3/8” (35 mm) MAX

Confirm that distance between Finished Wall

and top of Limiter Collar is between 1” (25 mm)

and 1-3/8” (35 mm).

If not, Spacer should be removed as follow:

How to remove the Spacer

Loosen.

Tighten.

Spacer

Right above

Circle Mark

Stem Adjuster

Limiter Collar

Temperature

Limiter

Temperature

Limiter

Stem Adjuster

Limiter Collar

1) Take out the Stem Adjuster, unscrew the

Limiter Collar and pull out the Temperature

Limiter.

2) Then, Remove the Spacer as shown.

3) Attach the Temperature Limiter, making

sure that Circle Mark on the Limiter align

with middle top point of the valve.

4) Then, tighten the Limiter Collar and

reattached the Stem Adjuster.

1) Be sure to reattach the Temperature

Limiter.

2) Tighten the Limiter Collar firmly.

3) Make sure the Circle Mark points

upward.

Caution

middle top point

ENGLISH

Before Use (after trims are installed)

HOT

COLD

Handle

KNOB

Volume

Control

Handle

about 104°F

Confirm the temperature of the water output.

1) Set the temperature control handle in the Mark at

“104” and confirm that output temperature is 104°F.

2) If temperature output is not 104°F, following adjustment

should be done.

To prevent scalding, the recommended hot water

temperature is 140°F (60°).

Confirming the outlet temperature and calibrating the valve

is required to minimize the risks of scalding.

After calibrated, the outlet temperature must read 104°F while

the temperature control handle knob is in the middle.

4) Installation of the Valve (the Finished Wall)

Lower LImit

Upper LImit

Guard Cover

Finished

Wall

Guard Cover

Guard

Cover

Guard

Cover

Single Volume

Control Valve

Dual Volume

Control Valve

Handshower

Adapter

Thermostatic Mixing

Valve

1) Fill the installation valve opening with

plumber’s putty or alike.

2) Again, make sure with the guard cover

provided that distance between Finished

Wall surface and valve falls between MIN

and MAX.

Caution

Leave the guard covers on all the valves till the

tile work is completed.

If the distance is beyond the MIN and MAX

limit, valve trim cannot be mounted

properly.

Must confirm wall, both rough and

finished, thickness and distance to the

valve before installing the valve.

ENGLISH

Please see following instruction on how to adjust the output

temperature if it is shown incorrectly in the previous step.

Screw

Cap

Mark

"104"

1) Keep turning the temperature control handle to the

Hot side while reading a temperature indicator.

Stop turning it when the indicator reads 104°F.

2) Let the water run while removing the

temperature control handle by taking off the cap

and unscrewing the screw.

3) Make sure that “104” on the handle is in

line with Mark on the coverplate and

reattach the temperature control handle.

4) Put the screw and cap on and, again, confirm the

output water temperature, making sure that it is 104°F

in the middle.

Loosen.

Tighten.

Spacer

Right above

Circle Mark

Stem Adjuster

Limiter Collar

Temperature

Limiter

Temperature

Limiter

Stem Adjuster

Limiter Collar

Calibrating the valve

calibrating the valve will be required if following the above

instructions do not result in correct remperature reading.

1) Shut of the HOT and Cold water supply

at the service stops.

2) Remove the Stem Adjuster, Limiter Collar

and temperature limiter.

3) Check to make sure that Circle Mark on

the temperature limiter align with middle

top point of the valve.

4) Reinstall the limiter and collar and turn on t

he water supply.

5) Turn the water on and let it run for about

1 minute. Place a thermometer in the water

stream while truning the handle to the HOT

side. Stop when it reads 104°F (40°C).

6)Let the water run at 104°F (40°C) water

temperature and then install the handle and cap.

NOTE: If the valve turned accidently, repeat the calibration procedure.

middle top point

Temperature

Control Handle

ENGLISH

Inhaltsverzeichnis

Sprachen:

Andere Toto Steuereinheit Handbücher

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung