Touch Revolution M19A Series Bedienungsanleitung

M19A Series

Touch Screen LCD Monitors

USER’s GUIDE

Rev.A

The information contained in this document is subject to change without notice.

This document contains proprietary information that is protected by copyright. All rights

are reserved. No part of this document may be reproduced,translated to another language

or stored in a retrieval system, or transmitted by any means, electronic, mechanical,

photocopying, recording, or otherwise, without prior written permission. Windows is a registered

trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective

holders.

The test results show that this device meets the FCC rules. Those limits are set to protect

residential areas from the devices with harmful emission. This device will produce, use and

radiate radio frequency energy. In addition, failure to follow the user’s manual to install or use

this device might produce harmful interference with radio communication. Not withstanding

the foregoing, it does not guarantee that this type of harmful interference does not occur in

some special installations. The interference caused by this device to the reception of radio

or television signals may be veried by turning it on and off. Any changes or modications to

this TFT LCD would void the user’s authority to

operate this device.

Important Recycle Instruction:

Lamp(s) inside this product contains mercury. This product may contain other

electronic waste that can be hazardous if not disposed of properly. Recycle or

dispose in accordance with local, state, or federal Laws. For more information,

contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specic

disposal information check WWW.LAMPRECYCLE.ORG.

Table of Contents

Usage Notice

Precautions............................................................................................................................. 1

Introduction

About M19A Series................................................................................................................. 2

Touch Screen for M19A-0101 ...................................................................................... 3

Package Overview ...................................................................................................... 4

Installation

Product Overview ........................................................................................................ 4

Front View.............................................................................................................. 4

Bottom View (Without Stand) .................................................................................. 4

Kensington Security Slot.............................................................................................. 5

VESA Mount for your Monitor....................................................................................... 6

Start Your Installation .................................................................................................. 7

Connecting the Display (Figure 10.1)........................................................................... 9

(Figure 10.1)...........................................................................................................10

User Controls

Side Panel Controls....................................................................................................11

How to Use the OSD Menus .......................................................................................12

On-Screen Display Menus ..........................................................................................13

Appendix

Troubleshooting..........................................................................................................14

Warning Signal ...........................................................................................................15

No Signal... .................................................................................................................15

Going to Sleep............................................................................................................15

Out of Range..............................................................................................................15

Product Dimensions ...................................................................................................16

Compatibility Modes ...................................................................................................17

Touch Screen Driver Installation .................................................................................18

M19A-0101 Install Instructions:...............................................................................18

Usage Notice

! Warning - To prevent the risk of re or shock hazards, do not expose

this product to rain or moisture.

! Warning - Please do not open or disassemble the product as this may

cause electric shock.

Precautions

Follow all warnings, precautions and maintenance as recommended in this user’s manual to

maximize the life of your unit.

Do:

• Turn off the product before cleaning.

• Touch screen surface may be cleaned using a soft clean cloth moistened with mild

window glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol.

• Use a soft cloth moistened with mild detergent to clean the display housing.

Don’t:

• Do not touch the LCD Display screen surface with sharp or hard objects.

• Do not use abrasive cleaners.

• Do not operate the product under the following conditions:

- Extremely hot, cold or humid environment.

- Areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic eld.

- In direct sunlight.

Introduction

About M19A Series

The M19A-0101 Series is a 19" at panel screen with an active matrix, thin-lm

transistor (TFT) liquid crystal display (LCD).

Features include:

• Direct Analog signal input

• Direct Digital signal input

•Active matrix TFT LCD technology

•1280 x 1024 SXGA resolution

•19" viewable display area

•31.47 ~ 80 KHz horizontal scan

•56 ~ 75 Hz high refresh rate

•0.294mm x 0.294mm pixel pitch

•Auto adjustment function

•Multilingual OSD user control

•Kensington security slot

•100 mm VESA mount

• Removable base for exible mounting solutions.

•M19A-0101 - Projected Capactive touch screen with USB controller

• Built-in speakers-1W x 2

Touch Screen for M19A-0101

• Projected Capactive touch screen for nger input only

• Surface: Clear glass

• Interface: USB controller

• HID: Windows®7,VISTA, XP, 2000, ME, 98

• Driver: Linux kernel 2.6.x (32 bit & 64 bit)

Package Overview

LCD Display Power Cord VGA Signal Cable

USB Cable ( A to B) Audio-in Cable DVI-D Cable

DC Power Supply

(sold separately)

Quick Start Guide

Cable Cover

Screw

Installation

Product Overview

• Front View

• Bottom View (Without Stand)

VGA IN

AC INAUDIO DVI IN

USB DC IN

Kensington Security Slot

The monitor can be secured to your desk or any other xed object with Kensington lock

security products. The Kensington lock is not included.

VESA Mount for your monitor

This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface

standard which denes a physical mounting interface for at panel monitors, and

corresponding with the standards of at panel monitor mounting devices, such as wall and

table arms. The VESA mounting interface is located on the back of your monitor.

To mount the monitor on a UL certied swing arm or other mounting xture, follow the

instructions included with the mounting xture to be used.

VESA

Mounting

Interface

Slots (x4)

100mm

75mm

*A/B: The distance between the shielding surface and the bottom of the screw hole is

8 mm.

! Warning!

Please select the proper screws!

Please use four M4 screws of adequate length for mounting your monitor.

Please note: the mounting stand must be able to support at least 15.4 lbs (7Kg)

Start Your Installation

1. Lay the LCD at on an even surface.

2. Remove the stand back cover by pulling in the direction of the arrow as seen in step 2

diagram.

3. Move the stand into position as seen in step 3 diagram.

4. Connect the cables to the appropriate connectors as seen in Step 4 diagram.

Step 2

USB VGA

Power

Audio

Step 4

Step 3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Touch Revolution Monitor Handbücher

Touch Revolution

Touch Revolution TDS-32F Series Bedienungsanleitung

Touch Revolution

Touch Revolution K32A Series Bedienungsanleitung

Touch Revolution

Touch Revolution M21A Series Bedienungsanleitung

Touch Revolution

Touch Revolution K15A Series Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung