TP-Link TL-SG1024 Bedienungsanleitung

Installation Guide

Gigabit Unmanaged Switch

TL-SG1048/TL-SG1024

TL-SG1024D/TL-SG1016

TL-SG1016D/TL-SG1008

Enterprise Networking Solution



Specifications are subject to change without notice. is a registered trademark

of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their

respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make

any derivative such as translation, transformation, or adaptation without permission from TP-LINK

http://www.tp-link.com



This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

This device may not cause harmful interference.1)

This device must accept any interference received, including interference that may cause2)

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.



This is a Class A product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.



This Installation Guide is also available in PDF on our web site. To obtain the

latest documentation and product information, please visit the official website:

http://www.tp-link.com



This Installation Guide describes the hardware characteristics, installation methods

and the points that should be attended to during installation. This Installation

Guide is structured as follows:

Chapter 1 Introduction. This chapter describes the external components of

the Switch.

Chapter 2 Installation. This chapter illustrates how to install the Switch.

Chapter 3 Lightning Protection. This chapter illustrates how to prevent

lightning damage.

Chapter 4 Connection. This chapter illustrates how to do the physical connec-

tion of the Switch.

Appendix A Troubleshooting.

Appendix B Specifications.

Appendix C Technical Support.



This Installation Guide is for:

Network Engineer

Network Administrator



Due to the similarity in structure of the Gigabit Unmanaged Switch series, in

this Installation Guide we take TL-SG1024 as an example to illustrate Chapter 2

Installation, Chapter 3 Lighting Protection and Chapter 4 Connection.

This Guide uses the specific formats to highlight special messages. The following

table lists the notice icons that are used throughout this guide.

Remind to be careful. A caution indicates a potential which may result in

device damage.

Remind to take notice. The note contains the helpful information for a

better use of the product.

Related Document

III



Contents

Chapter 1 Introduction ——————————— 01

1.1 Product Overview...................................................................01

1.2 Features......................................................................................01

1.3 Appearance...............................................................................02

Chapter 2 Installation ———————————— 05

2.1 Package Contents ...................................................................05

2.2 Safety Precautions ..................................................................05

2.3 Installation Tools......................................................................07

2.4 Product Installation................................................................08

Chapter 3 Lightning Protection ———————— 10

3.1 Cabling Reasonably................................................................10

3.2 Connect to Ground.................................................................12

3.3 Equipotential Bonding..........................................................13

3.4 Use Lightning Arrester..........................................................14

Chapter 4 Connection ——————————— 16

4.1 Ethernet Port ............................................................................16

4.2 Verify Installation ....................................................................16

4.3 Power On....................................................................................16

4.4 Initialization ..............................................................................17

Appendix A Troubleshooting ————————— 18

Appendix B Specications——————————— 19

Appendix C Technical Support ————————— 20

Gigabit Unmanaged Switch





The Gigabit Switch provides you with a high-performance, low-cost, easy-to-use,

seamless and standard upgrade to boost your old network to 1000Mbps. Increase the

speed of your network server and backbone connections, making Gigabit a reality.

Power users in the home, ofﬁce, workgroup, or creative production environment can

now move large, bandwidth-intensive ﬁles faster. Transfer graphics, CGI, CAD, or

multimedia ﬁles and other applications that have to move large ﬁles across the network

almost instantly.

The Gigabit Switch features a non-blocking switching architecture that forwards and

filters packets at full wire-speed for maximum throughput, MAC address auto-learning

and auto-aging, IEEE802.3x ﬂow control for full-duplex mode and backpressure for

half-duplex mode. It is compatible with all 10, 100 and 1000Mbps Ethernet devices

because it is standard-based. It protects your existing network investments while

providing you with a straightforward migration path to faster Gigabit speeds.

The Gigabit Switch is plug-and-play and no configuration is required. Auto MDI/MDI-X

cable detection on all ports eliminates the need for crossover cable or Uplink port. Each

port can be used as general port or Uplink port, and any port can be simply plugged

into a server, a hub, a router or a switch, using the straight cable or crossover cable.

Diagnostic LEDs which display link status and activity, allow you to quickly detect and

correct problems on the network.



Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab standards•

8/16/24/48 10/100/1000Mbps Auto-Sense RJ45 ports supporting Auto-MDI/MDIX•

All ports Support Full/Half Duplex transfer mode for 10/100Mbps and Full Duplex•

transfer mode for 1000Mbps

Supports IEEE802.3x ﬂow control for full-duplex mode and backpressure for half-•

duplex transfer mode

Non-blocking switching architecture that forwards and filters packets at full wire-•

speed for maximum throughput

Supports MAC address auto-learning and auto-aging•

LED indicators for monitoring power, link, speed and activity•

Desktop and rack-mountable steel case•

Internal power supply•

Introduction

Gigabit Unmanaged Switch



Front Panel



The front panel of TL-SG1048 is shown as the following figure.

Front Panel ofFigure 1-1 TL-S G10 4 8

The front panel of TL-SG1024 is shown as the following figure.

Front Panel ofFigure 1-2 TL-SG1024

The front panel of TL-SG1024D is shown as the following figure.

Front Panel ofFigure 1-3 TL-SG1024D

The front panel of TL-SG1016 is shown as the following figure.

Front Panel ofFigure 1-4 TL-S G1016

Introduction

LEDs

10/100/1000Mbps RJ45 Port

LEDs

10/100/1000Mbps RJ45 Port

LEDs

10/100/1000Mbps RJ45 Port

LEDs

10/100/1000Mbps RJ45 Port

Gigabit Unmanaged Switch

The front panel of TL-SG1016D is shown as the following figure.

Front Panel ofFigure 1-5 TL-S G1016D

The front panel of TL-SG1008 is shown as the following figure.

Front Panel ofFigure 1-6 TL-SG1008

LEDs

LED Status Indication

Power On The Switch is powered on

Off The Switch is powered off or power supply is abnormal

Link/Act

On There is a device linked to the corresponding port but

not active

Flashing The corresponding port is transmitting or receiving data

Off There is no device linked to the corresponding port

1000Mbps

On A 1000Mbps device is connected to the corresponding

port

Off A 10/100Mbps device or no device is connected to the

corresponding port

Note: TL-SG1048 has no 1000Mbps LEDs.

10/100/1000Mbps Port

Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. Each has a corresponding Link/Act LED and a 1000Mbps LED. TL-SG1048

has no 1000Mbps LEDs.

Introduction

LEDs

10/100/1000Mbps RJ45 Port

LEDs

10/100/1000Mbps RJ45 Port

Gigabit Unmanaged Switch

Rear Panel

The rear panel of TL-SG1048 is shown as the following figure.

Rear PanelFigure 1-7 of TL-SG1048

The rear panel of TL-SG1024/TL-SG1016 is shown as the following figure.

Rear PanelFigure 1-8 of TL-SG1024/TL-SG1016

The rear panel of TL-SG1024D/TL-SG1016D/TL-SG1008 is shown as the following figure.

Rear PanelFigure 1-9 of TL-SG1024D/TL-SG1016D/TL-SG1008

Power Socket

Connect the female connector of the power cord here, and the male connector to

the AC power outlet. Please make sure the voltage of the power supply meets the

requirement of the input voltage.

Grounding Terminal

The Switch already comes with lightning protection mechanism. You can also ground

the Switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.

For detailed information, please refer to Chapter 3 Lightning Protection.

Caution: Please use the provided power cord.

Introduction

Grounding Terminal

Power Socket

Grounding Terminal

Power Socket

Grounding Terminal

Power Socket

Gigabit Unmanaged Switch





Make sure that the package contains the following items. If any of the listed items is

damaged or missing, please contact your distributor.

One Switch One Power Cord This Installation Guide

Two mounting brackets and the

ﬁttings



To avoid any device damage and bodily injury caused by improper use, please observe

the following rules.

Safety Precautions



Keep the power off during the installation.



Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good



skin contact and is well grounded.

Use only the power cord provided with the Switch.



Make sure that the supply voltage matches the specifications indicated on the rear



panel of the Switch.

Ensure the vent hole is well ventilated and unblocked.



Do not open or remove the cover of the Switch.



Before cleaning the device, cut off the power supply. Do not clean it by the waterish



cloth, and never use any other liquid cleaning method.

Installation

Andere Handbücher für TL-SG1024

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TP-Link Schalten Handbücher

TP-Link

TP-Link Tapo H100 Bedienungsanleitung

TP-Link

TP-Link JetStream T1600G-28TS Bedienungsanleitung

TP-Link

TP-Link TL-SF1005D Bedienungsanleitung

TP-Link

TP-Link JetStream TL-SL3428 Bedienungsanleitung

TP-Link

TP-Link TL-SF1008P Bedienungsanleitung

TP-Link

TP-Link TL-SG105 Bedienungsanleitung

TP-Link

TP-Link JetStream TL-SG3452X Bedienungsanleitung

TP-Link

TP-Link TL-SG1008D - Switch Bedienungsanleitung

TP-Link

TP-Link JetStream TL-SL5428E Bedienungsanleitung

TP-Link

TP-Link T2500G-10MPS Bedienungsanleitung

TP-Link

TP-Link TL-SG3109 Bedienungsanleitung

TP-Link

TP-Link TL-SG1008PE Bedienungsanleitung

TP-Link

TP-Link Omada DS1016G Bedienungsanleitung

TP-Link

TP-Link TL-SG2216 Bedienungsanleitung

TP-Link

TP-Link TL-SX3016F Bedienungsanleitung

TP-Link

TP-Link JetStream T3700G-52TQ Bedienungsanleitung

TP-Link

TP-Link TL-SF1005D Bedienungsanleitung

TP-Link

TP-Link TL-SG3428X-UPS Bedienungsanleitung

TP-Link

TP-Link Omada SG2218P Bedienungsanleitung

TP-Link

TP-Link tapo S505D Bedienungsanleitung

TP-Link

TP-Link JetStream TL-SL5428E Bedienungsanleitung

TP-Link

TP-Link JetStream T1600G-52TS Bedienungsanleitung

TP-Link

TP-Link T3700G-28TQ Bedienungsanleitung

TP-Link

TP-Link JetStream TL-SL3452 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung