TPI CV Series Bedienungsanleitung

REV. 2/19 ECO 1-7514 1 of 4 FORM 9532

INSTALLATION

INSTRUCTIONS

INSTALLATION AND OPERATION INSTRUCTIONS

CV SERIES COVE HEATER

INSTALLATION INSTRUCTIONS:

The CV series cove heater is designed for wall or ceiling mount. Maintain at least 2-1/2” from the

ceiling and 3/4” from back of the heater to the wall. See illustration 2. Do not block the heater in any

manner. Maintain at least 6 inches between the heater and draperies.

1. The cove heater is provided with wall mounting brackets. The quantity of brackets is determined by

length. CV45 (2), CV60 thru CV90 (3) and CV100 thru CV125(4). See illustration 1.

2. The brackets should be mounted in a wall stud for secure mounting. Hollow wall anchors in drywall

are not recommended.

3. The CV series is provided with 1/4 inch knockouts along the back for attachment of wall mounting

brackets.

Should a stud be out of alignment with knockouts, a 1/4in. hole can be drilled for placement

of a bracket.

4. Remove the front cover by removing the screws along the bottom.

5. Determine the location of the mounting brackets and remove the corresponding 1/4 in. knockout.

Attach wall mounting bracket with nut and lockwasher. Position the cove heater and secure with the

appropriate hardware for the mounting surface. Alternately, the brackets may be mounted to the wall

and then mount the heater. More than one person may be required for mounting longer length units.

Once the back is secured to the wall, bring power into either end through the provided knockouts.

Note: Supply wire must be 90 deg. C wire. All connections should be made by a licensed electrician.

All wiring shall be in accordance with the N.E.C. or authority having juridiction.

6. Replace the front cover. Note: Do not over tighten the screws. The screws should be tight enough

to secure the cover but also allow expansion and contraction of the front.

7. Make wiring connections. See wiring diagrams for connections.

8. Note: The CV series does not have an intergral thermostat. The CV series must be controlled from

a remote wall thermostat.

OPERATION

1. Turn on the power supply to the heater.

2. Rotate thermostat knob fully clockwise.

3. Allow room to reach desired temperature, then rotate thermostat knob counter-clockwise until the

heater de-energizes. the thermostat will maintain temperature.

REV. 2/19 ECO 1-7514 2 of 4 FORM 9532

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of re,

electrical shock, and injury to persons, including the following:

1. Read all instructions before using this heater.

2. CAUTION:

High temperatures. Keep cords and all other combustible material, such as

furniture,

papers, clothes and curtains away from the heater. For safe and efcient operation,

keep an

open space around heater of three feet in front and 12 inches at ends and rear.

ATTENTION:

Les températures élevées. Gardez les cordons et tout autre matériau combustible,

tels que les meubles, papiers, vêtements et rideaux à l'extérieur de l'appareil de chauffage.

Pour

un fonctionnement sûr et efcace, garder un espace ouvert autour de chauffage

de trois pieds à

l'avant et 12 pouces aux extrémités et à l'arrière.

3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever

the heater is left operating and unattended.

4. Do not operate any heater after it malfunctions, has been dropped or damaged in any manner.

Return heater to authorized service facility for examination, electrical or mechanical adjustment, or

repair.

5. Do not use outdoors.

6. To disconnect heater, turn controls to off, and turn off power to heater circuit at main disconnect

panel (or operate internal disconnect switch if provided)

7. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause

an electric shock or re, or damage the heater.

8. To prevent a possible re, do not block air intakes or exhaust in any manner.

9. A heater has hot and arcing or sparking parts inside. WARNING: Do not use it in area where gasoline,

paint, or ammable liquids are used or stored.

10. Use this heater only as described in this manual. Any other use not recommended by the manufacturer

may cause re, electric shock, or injury to persons.

11. This heater may or may not include an audible or visual alarm to warn that parts of the heater are

getting excessively hot. If the alarm sounds (or illuminates), immediately turn the heater off and

inspect for any objects on or adjacent to the heater that may have blocked the airow or otherwise

caused high temperatures to have occured.

DO NOT OPERATE THE HEATER WITH THE ALARM SOUNDING (OR ILLUMINATING).

12. SAVE THESE INSTRUCTIONS

REV. 2/19 ECO 1-7514 3 of 4 FORM 9532

CEILING

2-1/2" MIN.

WALL

MOUNTING

CEILING

MOUNTING

WALL

34"

6 FEET MIN. ABOVE

FINISHED FLOOR

BREAK OFF

TOP SECTION

MOUNTING

BRACKET

CEILING

2-1/2" MIN.

WALL

34"

6 FEET MIN. ABOVE

FINISHED FLOOR

MOUNTING

BRACKET

BRACKET PLACEMENT

Illustration 1

ACCESSORIES

Ceiling Bracket - Catalog NO. CVCBX.

Install ceiling bracket similar to wall mounting brackets as explained in installation.

Blank Sections - Catalog No.’s CVB42X, CVB60X and CVB84X.

Install blank sections to ll space between heaters. Install blank sections same as heater. The blank

sections may be cut to desired length.

Illustration 2

CV45

CV60, CV75, CV90

CV100, CV110, CV125,

REV. 2/19 ECO 1-7514 4 of 4 FORM 9532

TYPICAL DIMENSIONS

WIRING DIAGRAMS

MAINTENANCE AND CLEANING

The heater should be cleaned at least annually to prevent excess build-up of dirt and lint accumulated

under normal operating conditions. In an unusually dirty environment the cleaning should be done more

often. Using a vacuum cleaner with soft brush attachment, clean the the front of the heater of any

accumulated dirt or lint. The face plate can be cleaned with damp cloth and mild detergent.

WALL

2 1/4"

1-7/16"

" K.O FOR

" CONDUIT

TOP VIEW

BACK VIEW

2.0"

4" KNOCKOUTS

FOR MOUNTING

TYPICAL

3-1/4"

4-1/4"

WIRING DIAGRAM FOR MULTIPLE UNITS

ELEMENT

BLACK

WHITEWHITE

WHITE

GND

POWER

SUPPLY ELEMENT

BLACK

WHITEWHITE

WHITE

ELEMENT

BLACK

WHITEWHITE

WHITE

GNDGND

ELEMENT

BLACK

WHITEWHITE

WHITE

GNDGND

LEFT HAND CONNECTION

POWER

SUPPLY ELEMENT

BLACK

WHITEWHITE

WHITE

GNDGND

RIGHT HAND CONNECTION

POWER

SUPPLY

WIRING DIAGRAM FOR SINGLE UNITS

NOTE: BOTH ELEMENT LEADS ARE BLACK ON 208 & 240 VOLT HEATERS.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung