Tracker Safe E Series Bedienungsanleitung
Owner Use
and
Care Manual
Tracker Safe LLC
6317 NE 63rd Street
Vancouver, WA 98661
(360) 213-0363
www.TrackerSafe.com
Document File: Tracker Safe-Manual-E, HS, M & TS Series-2022-09-01
M Series
Part #:
T592320M
T593024M
T593625M
T724227M
E Series
Part #:
T592320E
TS Series
Part #:
TS08
TS14
TS24
TS30
TS45
TS64
HS Series
Part #:
T202020S
T302020S
T402020S
Safe Identication...................................................................Page 3
Opening Your Safe for the First Time..................................Page 4
Lock Opertaion...................................................................... Page 4-7
Removing e Safe From e Pallet.....................................Page 8
Anchoring Your Safe To e Floor........................................Page 8
Shelf Installation......................................................................Page 9
Use, Care, & Maintenance.....................................................Page 10
Warranty...................................................................................Page 11
Table of Contents
2
Serial Number:
Original Receipt: (Attach Here)
Combination:
ATTENTION:
DO NOT STORE THIS MANUAL
IN YOUR SAFE
Tracker Safe LLC
6317 NE 63rd Street
Vancouver, WA 98661
(360) 213-0363
www.TrackerSafe.com
3
Opening your safe for the rst time
If the safe is in the unlocked position the door will open by turning the
handle clockwise until it stops. en pull door open.
If safe is in the locked position then please follow the directions below:
Use the Opening Index located at the twelve o’clock position.
1) Turn the dial LEFT(counterclockwise), passing the rst number in
your combination three times. en stop exactly on the number the
FOURTH time around.
2) Turn the dial RIGHT(clockwise), passing your second number in the
combination two times. en stop exactly on the number the THIRD
time around.
3) Turn the dial LEFT(counterclockwise), passing the last number in the
combination one time. en stop exactly on the number the SECOND
time around. ONE MORE STEP! SEE STEP #4
4) Turn the dial RIGHT(clockwise) until the dial stops completely. en
turn the safe handle clockwise to open the door.
To lock the safe: Close the door. Turn the handle counterclockwise until
it stops. Spin the dial FOUR complete turns either direction. Turn the safe
handle to be sure the safe is locked.
Mechanical Dial Lock:
Operating your Mechanical Dial Lock:
Important Notes:
•Turn the dial slowly and evenly.
•Do not over rotate past a number. If an
error is made, start from the beginning.
•Always view the dial straight on, not at an
angle.
4
Opening your safe for the rst time
5
WARNING:
Always perform code change with the door OPEN and the bolts
extended in the locked position.
1) With the door in the open position, enter “zero”(0) six(6) times.
2) Within four (4) seconds, enter the existing six (6) digit code ONE (1)
time.
3) Within four (4) seconds, enter the NEW six (6) digit code TWO(2)
times.
4) Test your new code several times before closing and locking the door.
Valid Code Entry: Two (2) Beeps at the same time as two (2) LED
ashes aer valid six(6) digit code is entered.
Invalid Code Entry: ree (3) Beeps at the same time as three (3) LED
ashes and the old code is still valid.
If a mistake is made while programming the new code, wait thirty (30)
seconds and repeat steps 1-3.
Electronic Lock:
Programing your Electronic Lock:
1) Turn the handle counter-clockwise until it stops.
2) Enter the factory code 1-2-3-4-5-6.
3) e lock will conrm a vaild combination with two (2) beeps at the
same time as two (2) LED ashes.
4) Within four (4) seconds, turn the handle clockwise until the handle
stops.
5) Pull the door open.
Invalid Combination Entry will be conrmed by three (3) beeps at the
same time as three (3) LED ashes.
Battery Replacement:
THERE ARE TWO TYPES OF BATTERY LOCATIONS
TYPE 1: DROP DOWN BATTERY COMPARTMENT:
1) Feel around the bottom right side of the keypad for a black
plastic latch and compartment. If you don’t feel or see this latch
or compartment then use the instructions for Type 2 on next page.
2) Release the latch by pulling the lever downward.
3) Pull down and remove the battery compartent from the bottom
of the keypad.
4) Remove the old battery and then press and hold each number
on the keypad for 5 seconds each.
5) Replace the battery with a new 9-volt alkaline battery with a
“use date” of at least 5 years in the future.
6) Put the battery compartment back into the keypad. Push it up
until it is in line or level with the cover. Press the latch/lever into
the keypad to lock the compartment in place.
Low Battery Warning:
Repeated LED ashing and beeping during an opening indicates
that the battery is low and needs immediate replacement.
Wrong Try Lock Out Period:
Four (4) consecutive invalid combinations starts a ve (5) minute
lock out period. e LED light will ash red at ten (10) second
intervals. At the end of the lock out period, two (2) more invalid
combinations will restart the ve (5) minute lock out period.
6
Operating the electronic Lock
Electronic Lock Continued
7
Replacing the Battery:
TYPE 2: SLIDE UP BATTERY COMPARTMENT:
1) Slide the entire keypad up;
parrallel with the door of the safe.
You will feel it “pop” loose.
2) Carfully pull the keypad away
from the safe and take care of
the wires.
3) Carefully disconnect the 9-volt battery from the terminals by
unsnapping the terminal connector located on top of the battery.
CAUTION: DO NOT PULL BATTERY LEADS/WIRES OUT
OF THE HOUSING!
4) Press and hold each number on the keypad for 5 seconds each.
5) Connect a new 9-volt alkaline battery with a “use date” of at
least 5 years in the future.
6) Push the battery and the wire leads completely into the
compartment.
CAUTION: BE VERY CAREFULL NOT TO PINCH THE
BATTERY LEADS.
7) Carefully position the keypad over the two mounting screws and
slide the keypad down until you feel a “pop”.
CAUTION: BE CAREFUL NOT TO PINCH THE WIRES.
Anchoring your Safe to the Floor
WARNING:
Safe must be bolted to the oor.
e safe presents a safety hazard (tipping) unless bolted down.
It is highly recommend to anchor your safe to the oor. is both
maximizes your protection from burglary/the but also prevents the safe
from tipping over.
Please see our website TrackerSafe.com for instructions on how to anchor
your safe. Due to various types of ooring materials and methods, you
may need to purchase dierent anchors.
Tracker Safe assumes no liabilty for any damages that may occur during
this anchoring process.
8
Removing Your Safe From The Pallet
WARNING:
Do not attempt this by yourself.
is process requires two or more adults.
Please see our website, TrackerSafe.com, for more details on how to
remove the safe from the pallet.
1) Cut the banding straps and remove the packaging.
2) Slide the safe sideways until about half of the safe is hanging over the
edge of the pallet. We recommend to have at least one adult on each side of
the safe.
3) Gently and slowly tilt the safe until the bottom of the safe touches the
ground.
4) Continue to tilt the safe in the same direction liing the safe o of the
pallet. While the safe is tilted o of the pallet, remove the pallet from
under the safe.
5) Gently and slowly lower the safe to the ground.
Shelf Installation
Step 1: Determine the desired height of the shelf.
Step 2: Insert the top of the clip into the desired notch then push
the bottom into the notch below the top notch.
9
Step 3: Repeat Step 2 for all 4 clips required for each shelf. Make
sure they are all aligned with one another.
Attention: Remove clips by pulling up on the bottom part of the clip.
Step 4: Move the shelf into the
safe angled diagonally (le side
lower then the right side) and
move it above the clips before
leveling the shelf. Bring the shelf
down onto the clips slowly.
Caution: Do not exceed 25
pounds on a single shelf.
Overloading shelves can cause
shelves or clips to break.
Use, Care, & Maintenance
PLACEMENT OF YOUR SAFE:
Before moving the safe into the desired location, be sure to plan
your route from the beginning to the end location. Make sure
you measure each doorway, stair, corner, or other obstacle before
moving the safe to be sure that it will t. Also, protect the various
types of ooring or stair materials that the safe will be traveling
across. e weight of the safe may damage some ooring.
It is recommended that you place a barrier between the safe and
the oor once the safe is in its nal position. A rubber mat, treated
wood, and carpet are good examples of barriers.
Make sure that you level your safe using shims. is will help the
safe door open smoothly. Shims are not included with your safe but
may be purchased from your local hardware store.
MOVING YOUR SAFE:
Caution: Never move a safe with any contents inside. is can
cause severe damage to the contents being stored and can possibly
cause the safe to be locked in the closed position due to shiing of
contents.
In the event that you have to move the safe, it is best to have a
certied safe technician maintain the safe before moving.
EXTERIOR CLEANING:
Use a so cloth like a microber cloth with a mild cleaner (i.e.,
window cleaner) to clean the exterior of the safe. Make sure to wipe
dry and never use harsh cleaners. Wipe around logos and graphics
gently.
MOISTURE/HUMIDITY:
We recommend that you use some form of a dehumidier to
control the level of moisture inside the safe.
10
Dieses Handbuch passt für folgende Modelle
17
Inhaltsverzeichnis
Andere Tracker Safe Sicher Handbücher
Beliebte Sicher Handbücher anderer Marken
Honeywell
Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Bedienungsanleitung
Hornady
Hornady SnapSafe Trunk Safe II Bedienungsanleitung
SPORTS AFIELD
SPORTS AFIELD SA-HD5-BIO Bedienungsanleitung
Honeywell
Honeywell 5912 Bedienungsanleitung
Phoenix
Phoenix FS1280F Bedienungsanleitung
Phoenix
Phoenix SS0992K Produktinformationsblatt
Technomax
Technomax Trony Series Handbuch
SPORTS AFIELD
SPORTS AFIELD INSTINCT BIOMETRIC Series Bedienungsanleitung
RICHTER CZECH
RICHTER CZECH LA Bedienungsanleitung
Olymp
Olymp GOsafe 110 Bedienungsanleitung
Phoenix
Phoenix SS0100E Produktinformationsblatt
Clarke
Clarke Strong-Arm CS1000K Bedienungsanleitung