Trackspot 60600033 Bedienungsanleitung

Part No. 60600033

h End S

stems, Inc.

2217 West Braker Lane

Austin, TX 78758 U.S.A.

Special Analog Controller

User Guide

ENABLE value

program audio

random

pause

bump

intensity rate

standby



Version 1.0, June 1993

User Guide

Trackspot®Special Analog Controller

Contents

Introduction...............................................................................................1

Section I

Master/Slave Mode.................................................................................1

Setup...................................................................................................1

Boot-up ...............................................................................................2

Section II

LED Indicators and Associated Keys............................................2

Enable.................................................................................................2

Standby...............................................................................................3

Program............................................................................................. 3

Automatic Program Step.....................................................................3

Intensity...............................................................................................3

Rate ....................................................................................................3

Audio...................................................................................................3

Random ..............................................................................................3

Pause .................................................................................................4

Section III

Non-Illuminated Keys...........................................................................4

Arrow “up” .......................................................................................... 4

Arrow “down”...................................................................................... 4

Bump...................................................................................................4

Section IV

Supllemental Features........................................................................ 4

EPROM Version/LED Test..................................................................4

Special Modes ....................................................................................4

Rate ....................................................................................................4

Audio.................................................................................................. 5

Special Analo

Controller 1

Section V

Warranty Procedures............................................................................5

Saving the Shipping Materials ............................................................5

Limited Warranty................................................................................ 5

Returning an Item Under Warranty for Repair ................................... 5

Getting Help

High End Systems Service provides a help line should you encounter problems

during your installation or initial operation. Currently, service hours are 8 a.m. to 6

p.m. (Central), Monday through Friday. The numbers are:

Telephone: (800) 890-8989

24 hour Fax: (512) 834-9195

24 hour voice mail: (512) 837-3053

or (800) 890-8989

2 Special Analo

Controller

Introduction

The

trackspot

Special Analog Controller is equipped with features that enable you to interact with the

fixture. It provides you with the ability to access and manipulate the 32 programs stored in the

trackspot

EPROM.

The Special Analog Controller features include:

• Self powered (from

trackspot

Master)

• Controls Master fixture

• Accesses 32 preset programs

• Fixture homing upon enable

• LED output monitors

• Seven segment display (SSD) LED’s

• Fixture remote enable/disable

• Standby

• Program select

• Program scroll

• Automatic program step

• Master intensity control

• Program step rate

• Audio program advance rates

• Random step change

• Mirror pause

• Value control (up and down arrows)

• EPROM version/LED test

• Special rate and audio modes

Section I: Master/Slave Mode

The Special Analog Controller is connected to the selected Master fixture through an 8-pin DIN connector

cable. Once connected, the controller may be used to access trackspot’s 32 preset programs.

Setup

When the Master fixture is plugged in and its personality switch eight is on, pin one of the 8-pin DIN

connector supplies unregulated 24 volts DC to the controller.

• Make sure the Master fixture is unplugged.

• Use a 24 AWG, 150 ft. (maximum) 8-pin DIN shielded cable to connect the controller to the Master

fixture.

• Use 3-pin XLR, two-conductor data cables to connect the Master and Slaves in the Daisy Chain

method (see Example 1.A, page 2).

• Turn the Master fixture personality switch eight on, and set the address switch to equal the number of

total units (including the Master).

Note: The Special Analog Controller must be connected to the Master fixture (personality eight on) to

operate. If switch eight is off, the controller will not receive the necessary voltage to work.

• Turn the Slave fixtures personality switch three on, and set each Slave’s address switch to the

sequential order of each unit.

ENABLE value

program audio

random

pause

bump

intensity rate

standby



Seven Segment Display LEDs

Special Analo

Controller 3

Example 1.A

Boot-up

The Special Analog Controller draws its power from the selected Master fixture. It receives unregulated 24

volts DC from the Master fixture through a single eight-conductor low voltage cable. When the Master

fixture is on and its personality switch eight is in the on position, the controller is on, even though all front

panel LED’s are off.

•The controller appears “off” when the Master fixture is first plugged in (personality switch eight on), or

when the controller is disabled. All LED’s are off. However, at this time the controller is active and

monitoring the Enable key, waiting to be booted up.

• When you press the Enable key, you will see the boot-up routine. The Enable LED illuminates, the

Standby LED flashes, and the Seven Segment Display (SSD) LED’s show three horizontal bars.

• During this time, the controller is initializing the Master fixture. When the Master fixture has homed, it will

cause all Slave fixtures to home.

• After homing, the Enable, Standby, and Program LED’s remain illuminated, while the Rate LED flashes,

and the Seven Segment Display LED’s show 01. This indicates that the controller is enabled and in the

standby mode.

• The flashing Rate LED signals that the controller will use time as a trigger for the next page of the

selected program.

• The default values at start-up are; Program one, Rate at level three and active, and Audio at level three

and inactive.

Note: You may check this by pushing the associated keys.

Section II: LED Indicators and Associated Keys

Eight of the eleven Keys on the Special Analog Controller have an associated LED. When the LED

remains illuminated, that function has been selected and becomes activated.

Enable LED off: The controller and fixtures are in an off state.

LED on: The controller and fixtures are ready for use.

Note: Each time Enable is cycled off/on, the fixtures will home.

FIXTUR E MODE SWITCHES 1-2

NORMAL RUN

SELF T EST

SET-U P

NONE

1,2

LIGHT WAV E CON TROL

DMX1-256

DMX 257-512

ANA LOG

AUDIO (SLAVE)

AUDIO (M A ST ER )

PAN INVERT

TILTINVERT

NONE

4,5

AU D IO MICPE RSO NA L ITYADD R ESSEN AB LEFAN

ANALOGIN

DATAOUTDATAIN

2209WESTBRAKERLANE,AUSTIN, TEXASU.S. A.

LIGHTW AVE R ESE ARCH

CONTRO LMODESWITCHES3-8

PER SONA L I TYSWITCHES

PLEA SE CO NSULTUSERMANUAL

FORFURTHERIN FORMATION

LAMP SAVE

PLEA SE CO NSULTUSERMANUAL

FORFURTHERIN FORMATION

SW ITCHES ON

SW ITCHESADDRESS ADDRESS

1,2,3,524 2,3,523 1,3,522 3,521 1,2,520 2,519 1,518 517 1,2,3,416 2,3,415 1,3,414 3,413

1,2,412 2,411 1,410 409 1,2,308 2,307 1,306 305 1,204 203 102 none01

FUS E

VOLTAGESELECT

WA RNING:CHANGE VOLTAGESELECTONLYWITHPOWERREMOVED.

CAUTION:HOTRE MO VE POWERBEFORER ELAMPING

WA RNING:NOTFORRE SIDE NT IALUSE.TOREDUCETHERISKOF

FIR E OR ELE CT RI C SHOCK,DONOTEXPOSETORAINOR M OI ST UR E,

NOUSER SERVICEABLEPARTSINSIDE.REFERSERVIC INGTO

QUALIFIEDSERVICEPE RSONNEL.FORSAFEOPERATIONCONSULT

USERMANUAL.

(UNREG.)

OUT

INPUT

SPEC I AL ANALOG

CONSULTUSERSMANUAL

FORFUTHERINFORMATION

24V DC

SHUTTE R

MSPEED

TILT

GOBO DIM

PAN

COLOR

167

GND

ANA LOG

0-10V

GND



MODEL

SERIAL

FACTO RY SET VA C

WATTS HZ

DATE QC

FIXTUR E MODE SWITCHES 1-2

NORMAL RUN

SELF T EST

SET-U P

NONE

1,2

LIGHT WAV E CON TROL

DMX1-256

DMX 257-512

ANA LOG

AUDIO (SLAVE)

AUDIO (M A ST ER )

PAN INVERT

TILTINVERT

NONE

4,5

AU D IO MICPE RSO NA L ITYADD R ESSEN AB LEFAN

ANALOGIN

DATAOUTDATAIN

2209WESTBRAKERLANE,AUSTIN, TEXASU.S. A.

LIGHTW AVE R ESE ARCH

CONTRO LMODESWITCHES3-8

PER SONA L I TY SW ITCHES

PLEA SE CO NSULTUSERMANUAL

FORFURTHERIN FORMATION

LAMP SAVE

PLEA SE CO NSULTUSERMANUAL

FORFURTHERIN FORMATION

SW ITCHES ON

SW ITCHESADDRESS ADDRESS

1,2,3,524 2,3,523 1,3,522 3,521 1,2,520 2,519 1,518 517 1,2,3,416 2,3,415 1,3,414 3,413

1,2,412 2,411 1,410 409 1,2,308 2,307 1,306 305 1,204 203 102 none01

FUS E

VOLTAGESELECT

WA RNING:CHANGE VOLTAGESELECTONLYWITHPOWERREMOVED.

CAUTION:HOTRE MO VE POWERBEFORER ELAMPING

WA RNING:NOTFORRE SIDE NT IALUSE.TOREDUCETHERISKOF

FIR E OR ELE CT RI C SHOCK,DONOTEXPOSETORAINOR M OI ST UR E,

NOUSER SERVICEABLEPARTSINSIDE.REFERSERVIC INGTO

QUALIFIEDSERVICEPE RSONNEL.FORSAFEOPERATIONCONSULT

USERMANUAL.

(UNREG.)

OUT

INPUT

SPEC I AL ANALOG

CONSULTUSERSMANUAL

FORFUTHERINFORMATION

24V DC

SHUTTE R

MSPEED

TILT

GOBO DIM

PAN

COLOR

16 73

GND

ANA LOG

0-10V

GND



MODEL

SERIAL

FACTO RY SET VA C

WATTS HZ

DATE QC

FIXTUR E MODE SWITCHES 1-2

NORMAL RUN

SELF T EST

SET-U P

NONE

1,2

LIGHT WAV E CON TROL

DMX1-256

DMX 257-512

ANA LOG

AUDIO (SLAVE)

AUDIO (M A ST ER )

PAN INVERT

TILTINVERT

NONE

4,5

AU D IO MIC

PE RSO NA L IT Y

ADD R ESSEN AB LEFA N

ANALOGIN

DATAOUTDAT A IN

2209WESTBRAKERLANE,AUSTIN, TEXASU.S. A.

LIGHTW AVE R ESE ARCH

CONTRO LMODESWITCHES3-8

PER SONA L I TY SW ITCHES

PLEA SE CO NSULTUSERMANUAL

FORFURTHERIN FORMATION

LAMP SAVE

PLEA SE CO NSULTUSERMANUAL

FORFURTHERIN FORMATION

SW ITCHES ON

SW ITCHESADDRESS ADDRESS

1,2,3,524 2,3,523 1,3,522 3,521 1,2, 520 2,519 1,518 517 1,2, 3,416 2,3, 415 1,3,414 3,413

1,2,412 2,411 1,410 409 1,2,308 2,307 1,306 305 1,204 203 102 none01

FUS E

VOLTAGESELECT

WA RNING:CHANGE VOLTAGESELECTONLYWITHPOWERREMOVED.

CAUTION:HOTRE MO VE POWERBEFORER ELAMPING

WA RNING:NOTFORRE SIDE NT IALUSE.TOREDUCETHERISKOF

FIR E OR ELE CT RI C SHOCK,DONOTEXPOSETORAINOR M OI ST UR E,

NOUSER SERVICEABLEPARTSINSIDE.REFERSERVIC INGTO

QUALIFIEDSERVICEPE RSONNEL.FORSAFEOPERATIONCONSULT

USERMANUA L.

(UNREG.)

OUT

INPUT

SPEC I AL ANALOG

CONSULTUSERSMANUAL

FORFUTHERINFORMATION

24V DC

SHUTTE R

MSPEED

TILT

GOBO DIM

PAN

COLOR

16 73

GND

142

ANA LOG

0-10V

GND



MODEL

SERIAL

FACTO RY SET VA C

WATTS HZ

DATE QC

FIXTUR E MODE SWITCHES 1-2

NORMAL RUN

SELF T EST

SET-U P

NONE

1,2

LIGHT WAV E CON TROL

DMX1-256

DMX 257-512

ANA LOG

AUDIO (SLAVE)

AUDIO (M A ST ER )

PAN INVERT

TILTINVERT

NONE

4,5

AU D IO MIC

PE RSO NA L IT Y

ADD R ESSEN AB LEFAN

ANALOGIN

DATAOUTDATAIN

2209WESTBRAKERLANE,AUSTIN, TEXASU.S. A.

LIGHTW AVE R ESE ARCH

CONTRO LMODESWITCHES3-8

PER SONA L I TY SW ITCHES

PLEA SE CO NSULTUSERMANUAL

FORFURTHERIN FORMATION

LAMP SAVE

PLEA SE CO NSULTUSERMANUAL

FORFURTHERIN FORMATION

SW ITCHES ON

SW ITCHESADDRESS ADDRESS

1,2,3,524 2,3,523 1,3,522 3,521 1,2,520 2,519 1,518 517 1,2,3,416 2,3,415 1,3,414 3,413

1,2,412 2,411 1,410 409 1,2,308 2,307 1,306 305 1,204 203 102 none01

FUS E

VOLTAGESELECT

WA RNING:CHANGE VOLTAGESELECTONLYWITHPOWERREMOVED.

CAUTION:HOTRE MO VE POWERBEFORER ELAMPING

WA RNING:NOTFORRE SIDE NT IALUSE.TOREDUCETHERISKOF

FIR E OR ELE CT RI C SHOCK,DONOTEXPOSETORAINOR M OI ST UR E,

NOUSER SERVICEABLEPARTSINSIDE.REFERSERVIC INGTO

QUALIFIEDSERVICEPE RSONNEL.FORSAFEOPERATIONCONSULT

USERMANUA L.

(UNREG.)

OUT

INPUT

SPEC I AL ANALOG

CONSULTUSERSMANUAL

FORFUTHERINFORMATION

24V DC

SHUTTE R

MSPEED

TILT

GOBO DIM

PAN

COLOR

16 73

GND

14 2

ANA LOG

0-10V

GND



MODEL

SERIAL

FACTO RY SET VA C

WATTS HZ

DATE QC

master

fixture

slave 1 slave 2

slave 3

ADDRESS

8 7 6 5 4 3 2 1

PERSONALITY

8 7 6 5 4 3 2 1

ADDRESS

8 7 6 5 4 3 2 1

PERSONALITY

8 7 6 5 4 3 2 1

ADDRESS

8 7 6 5 4 3 2 1

PERSONALITY

8 7 6 5 4 3 2 1

ADDRESS

8 7 6 5 4 3 2 1

PERSONALITY

8 7 6 5 4 3 2 1

ENABLE value

program audio

random

pause

bump

intensity rate

standby



8-Pin DIN Connected To

Special Analo

Controller

4 Special Analo

Controller

Standby LED off: The controller and fixtures are active and displaying the selected program(s).

LED on: The controller and fixtures are in standby. The fixture lamp is out, and all

advance functions are halted. In this mode, the controller keyboard is active

and new settings may be selected. When you exit standby, the new settings will

take effect.

Program LED off: You cannot change the program selection. The controller will return to the

program selection mode approximately ten seconds after operator interaction

with Intensity, Rate, or Audio selection has ceased.

LED on: You can change the program selection with the Arrow keys. Holding the Arrow

keys down will allow scrolling through the programs. Holding the Program key

down while using the Arrow keys will allow program changes without updating

the fixture. You may make a smooth transition from one program to another

without having to sequentially step through programs. A decimal point is

displayed in the Seven Segment Display to indicate that this feature is in

effect. Releasing the Program key will cause the new program to be viewed.

Automatic When the Program LED is on, eight additional Automatic Program Step

modes may be selected by using the Arrow keys. Program modes A1 to A8 will

cause program advance at various time intervals. A1 is the slowest, with

changes at approximately one minute intervals. A8 is the fastest, with changes

at approximately six second intervals.

Intensity LED off: You cannot change the lamp intensity.

LED on: You can change the lamp intensity by using the Arrow keys. Sixteen levels are

available to the user, with level sixteen being full on, and level 1 being full off.

The levels will wrap from sixteen to one, or one to sixteen, by pushing the “up”

Arrow key or “down” Arrow key. This allows toggling the lamp off and on; or, the

the intensity may be varied smoothly by stepping down/up between sixteen and

one. You may deselect Intensity by pushing the Program key, or by letting the

controller do it on its own (after you discontinue to interact with the controller).

Rate LED off: Pushing the Rate key while the Rate LED is solidly illuminated, or, pushing

the flashing Rate LED key twice, will disable rate triggering. When the LED is

off, you cannot change the value of rate triggering, or use Rate as a page step

trigger. The mirror pauses.

LED on: You can change the value of rate triggering by using the Arrow keys. Five levels

and “off” are available. Rate triggering uses time to step between pages in a

program. Level one is the slowest, and level five is the fastest. You may return

to Program select without disabling rate triggering by pushing the Program key,

or by letting the controller do it on its own (after you discontinue to interact with

the controller).The controller stores the value of rate triggering, and that value

is remembered the next time the Rate key is pushed.

LED flashing: Rate is being used as a page step trigger, and the level selected is other

than “off”.

Note: A display of “off” on the Seven Segment Display indicates that rate triggering is off.

Audio LED off: Pushing the Audio key while the Audio LED is solidly illuminated, or, pushing

the flashing Audio LED key twice, disables audio triggering. You cannot change

the value of audio triggering when the LED is off, or use Audio as a trigger. The

mirror pauses.

LED on: You can change the value of Audio triggering with the Arrow keys. Five levels

and “off” are available. Audio triggering uses beat width to step between pages.

Level one is the least sensitive and requires a wide/heavy beat to trigger the

next page. Level five is most sensitive and only requires a narrow/light beat to

trigger the next page. You may return to Program select without disabling

audio triggering by pushing the Program key, or by letting the controller do it on

its own (after you discontinue to interact with controller). The controller stores

the value of rate triggering, and that value is remembered the next time the

Audio key is pushed.

LED flashing: Audio is being used as a page step trigger, and the level selected is other

than “off”.

Note: A display of “off” on the Seven Segment Display indicates that rate triggering is off.

Reiteration: If the Rate/Audio LED is solidly illuminated, and the Rate/Audio key is

pushed again, the current value is stored, Rate/Audio page step triggering is

disabled, and the Program selection mode is restored. Pushing the Rate/Audio

key again will restore the stored value. This allows the user to jump in and out

of various triggering modes without having to push the “up” and “down” Arrow

keys. To return to Program mode without disabling Rate/Audio triggering,

simply push the Program key.

Random LED off: Pages in a program are played in their normal order.

Special Analo

Controller 5

LED on: Pages in a program are selected in a random order.

Note: Rate, Audio or Bump must be activated in order for this to work. Otherwise there

will be no mirror movement or page change.

Pause LED off: The mirror head functions normally.

LED on: The mirror head will “freeze” at its current position. The position may be any

point along the mirror head travel, and not necessarily on a program step

position. All other functions are unaffected. This allows the user to illuminate a

particular area, and still utilize all the other features of the trackspot. For

example, trackspot will continue to step through program(s) and pages.

Note: Rate or Audio must be activated to utilize other features.

Section III: Non-Illuminated Keys

The Special Analog Controller also has three non-illuminating keys; “up” Arrow, “down” Arrow, and Bump.

Use these keys to change the values of function keys such as, Program, Intensity, Rate, and Audio

triggering. For example, you may affect the program selection by pushing the associated key (Program) to

illuminate its LED. Then you may push the “up” or “down” Arrow key to change programs.

Arrow Pushing the “up” Arrow when a function LED is illuminated increases the selected value.

“up” If the Arrow key is held down, the selected value will scroll to its maximum value. If the

value is at its maximum, the next push of the “up” Arrow will cause the value to wrap to its

minimum value.

Arrow Pushing the “down” Arrow when a function LED is illuminated decreases the selected

“down” value. If the Arrow key is held down, the selected value will scroll to its minimum value. If

the value is at its minimum, the next push of the “down” Arrow will cause the value to

wrap to its maximum value.

Bump Pushing the Bump key when a function LED is illuminated selects the next program. The

Bump key has effect in addition to whatever rate or audio triggering might be selected.

Note: You may also “bump” pages without activating Rate or Audio.

Section V: Supplemental Features

Three supplemental features are included in each Special Analog Controller; EPROM version test,

special rate mode, and special audio mode. You may use the EPROM version test to identify the Special

Analog firmware version.

There are six Special Rate modes and four Special Audio modes included in the current version (1.0) of

the firmware. Since control of the trackspot fixture by the Special Analog Controller is unidirectional and

asynchronous in the truest since of the word, the effect of these modes is dependent on the particular

program being viewed. Following is a description of the three features.

EPROM The version number of the EPROM for the trackspot Special Analog

Controller may be seen by holding down the Enable key while the fixture is

homing. When the controller comes out of the homing delay, the Seven

Segment Display (SSD) will hold the EPROM version number. Also at this time,

all LED’s will light in a lamp test. Normal operation will resume when you

release the Enable key.

Special Modes

You can recognize the special modes by the horizontal bars in the left digit of the Seven Segment

Display (SSD). The placement of the bars is meant to serve as a reminder of how the mode steps. A

single bar at the bottom indicates the stepping starts at 1 and proceeds upward in single steps. A single

bar at the top indicates the stepping starts at 5 and proceeds downward in single steps. A single bar in the

middle indicates the middle modes (2, 3, 4) are stepped singly. A top and bottom bar indicate a random

choice between 1 and 5. A bottom and middle bar indicates stepping starts at 1 and proceeds in steps of

two (1, 3, 5). A top and middle bar indicates stepping starts at 5 and proceeds downward in steps of two

(5, 3, 1).

Rate • When the SSD shows _I, the controller will step from rate 1 to rate 5, then wrap to rate 1

and repeat.

• When the SSD shows 2, the controller will step from rate 5 to rate 1, then wrap to rate

5 and repeat.

Note:

Rate 1 is the slowest speed and rate 5 is the fastest speed.

• When the SSD shows 3, the controller will step from rate 2 to rate 4, then wrap to rate

2 and repeat. The controller steps through the middle three rates.

• When the SSD shows _4, the controller will randomly select one of the five rates.

Special Analo

Controller 6

• When the SSD shows 5, the controller will step from rate 1 to rate 3 to rate 5, then

wrap to rate 1 and repeat. The controller steps up by two.

• When the SSD shows 6, the controller will step from rate 5 to rate 3 to rate 1, then

wrap to rate 5 and repeat. The controller steps down by two.

Audio • When the SSD shows _1, the controller will step from audio 1 to audio 5, then wrap to

audio 1 and repeat.

• when the SSD shows 2, the controller will step from audio 5 to audio 1, then wrap to

audio 5 and repeat.

Note: Audio 1 is the least sensitive and audio 5 is the most sensitive.

• When the SSD shows 3, the controller will step from audio 1 to audio 3 to audio 5, then

wrap to audio 1 and repeat. The controller steps up by two.

• When the SSD shows 4, the controller will step from audio 5 to audio 3 to audio 1, then

wrap to audio 5 and repeat. The controller steps down by two.

Section V: Warranty Procedures

Please follow all procedures pertaining to the Special Analog Controller. This will help ensure better

service from your HES Dealer/Distributor.

Saving the Shipping Materials

• Do not discard the Special Analog Controller shipping carton and packing materials. These shipping

cartons and packing materials are specifically designed to protect these products during transport.

• If you ever need to return a product for repair maintenance, you must return it in its original shipping

carton and packing materials. You will be billed for a new shipping carton and new packing materials if

you return your Special Analog Controller in a non-factory shipping carton with non-factory packing

materials.

Note: Before sending anything to the factory, be sure to call your HES Dealer/Distributor for a Return

Authorization Number (RA#). Any goods shipped without an RA number will be refused at the

factory.

• The contents of each shipping carton should be carefully removed and inspected for signs of freight

damage. If any such damage is found, you need to notify both the shipping agent and the sales agent

immediately.

• Any damage incurred in shipping is the responsibility of the carrier. In the case of hidden damage, a

claim should be made as soon as discovered and all packing material retained for inspection.

Note: Freight Damage Claims are invalid for fixtures shipped in non-factory shipping cartons and packing

materials.

Limited Warranty

Your Special Analog Controller is covered by a one year parts and labor limited warranty. It is the owner’s

responsibility to furnish receipts or invoices for verification of purchase, date, and dealer or distributor. If

purchase date cannot be provided, date of manufacture will be used to determine warranty period.

Returning an Item Under Warranty for Repair

• It is necessary to obtain a return Authorization Number (RA#) from your dealer/distributor BEFORE any

units are sent in for repair. The manufacturer will make the final determination as to whether or not the

unit is covered by warranty. This warranty does not cover lamps, fuses, or glass parts.

• All shipping will be paid by the purchaser. Items under warranty shall have return shipping paid by the

manufacturer only in the Continental United States. Under no circumstances will freight collect

shipments be accepted. Prepaid shipping does not include rush expediting, such as air freight. Air

freight can be sent customer collect in the Continental United States.

• Any product unit or part returned to High End must be packaged in a suitable manner to ensure the

protection of such product unit or part, and prominently marked to indicate that the package contains

returned product units or parts, with a Return Authorization (RA#) number.

Notice: Repair or replacement as provided for under this warranty is the exclusive remedy of the

consumer. High End Systems, Inc. makes no warranties, expressed or implied, with

respect to any product, and High End specifically disclaims any warranty of

merchantability or fitness for a particular purpose. High End shall not be liable for any

indirect, incidental or consequential damages, including lost profits, sustained or

incurred in connection with any product or caused by product defects, or the partial or

total failure of any product, regardless of the form of action, whether in contract, tort

(including negligence), strict liability or otherwise, and whether or not such damages

were foreseen or unforeseen.

• Warranty is void if the product is misused, damaged, or modified in any way. This warranty gives you

specific legal rights, and you may also have other rights which vary from state to state.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung