Tracmaster CAMON TC07 Betriebsanleitung

CAMON

MAINTENANCE GUIDE

TC07

TURF CUTTER

TC07 Turf Cutter

MAINTENANCE GUIDE

Contents

TC07/1003/MG/1

THIS GUIDE CONTAINS THE FOLLOWING INFORMATION:

1. Maintenance Overview

2. Trouble-Shooting Guide

3. Changing the Crankshaft Drive Belt

4. Replacing the Wheel Drive Belt

TC07 Turf Cutter

MAINTENANCE GUIDE

Maintenance Overview

TC07/1003/MG/2

OPERATION DAILY EVERY

WEEK

EVERY

MONTH

ENGINE Check engine oil level 10W/40

See separate engine manual

X X

Check condition of blade X

Check driving belts X

Check clutch operation X

Check operating lever and cable X

Tighten all nuts and bolts X

Lubricate wheel bearings X

Check tyre pressures (20psi) X

Lubricate sliding clutch and shaft X

MACHINE

Lubricate drive chain X

NOTE:

* DO NOT allow maximum engine speed to exceed 2800rpm.

* DO NOT pressure wash the transmission assembly.

TC07 Turf Cutter

MAINTENANCE GUIDE

TC07/1003/MG/3

Trouble-Shooting Guide

PROBLEM POSSIBLE CAUSE REMEDY

No drive to blade Loose engine belt Tighten belt

Poor wheel drive Loose drive belt Tighten belt

Poor cutting performance Blunt or damaged blade Straighten, sharpen or

replace blade

Machine does not go in a

straight line

Incorrect tyre pressures Check pressure at 15psi

NOTE:

* DO NOT allow maximum engine speed to exceed 2800rpm.

TC07 Turf Cutter

MAINTENANCE GUIDE

Changing the

Crankshaft Drive Belt

TC07/1003/MG/4

PIVOT POST

RETAINING NUTS

BLADE ARM ASSEMBLY

BLADE BOLTS

BLADE

CRANKSHAFT

PULLEY

CLUTCH

ENGINE BOLTS

RIGHT-HAND GUARD

INSTRUCTIONS

1. Remove the right hand guard.

2. Remove the blade bolts and take off the blade.

3. Remove the blade arm assembly retaining nuts.

4. Pull the blade arm assembly off the pivot post and crankshaft.

5. Remove the belt from the pulley and clutch.

6. Fit the new belt.

7. Adjust the belt tension by undoing the engine bolts and moving the engine in its mounting slots.

8. Tighten the engine bolts.

9. Re-assemble in reverse order.

TC07 Turf Cutter

MAINTENANCE GUIDE

TC07/1003/MG/5

PIVOT POST

BELT TENSIONER

CARRIER BOLTS

REMOVE AND CHANGE BELT HERE

GEARBOX PULLEY

SPACER

CRANKSHAFT

BEARING

GRUB SCREWS

LEFT-HAND GUARD

BEARING CARRIER

RETAINING NUTS

BLADE ARM ASSEMBLY

BLADE BOLTS

BLADE

LEFT-HAND CHASSIS WITH BEARING REMOVED

LEFT-HAND CHASSIS

Replacing the

Wheel Drive Belt

INSTRUCTIONS

1. Remove the left hand guard.

2. Remove the blade.

3. Remove the nuts off the crankshaft (A) and pivot post (B).

4. Pull the blade arm assembly off.

5. Remove the spacer from the crankshaft.

6. Release the belt tensioner and roll the belt off the gearbox pulley.

7. Undo the two grubscrews in the crankshaft bearing.

8. Remove the carrier bolts from the bearing carrier.

9. Pull the crankshaft bearing off the crankshaft.

10. The belt can now be removed and replaced through the side of the chassis.

11. Reverse this process to reassemble and set the belt tensioner. Use a little blue loctite on the

grubscrews and do not overtighten them.

Teknol House | Victoria Road | Burgess Hill | RH15 9LH

T: 01444 247689 | F: 01444 871612 | www.tracmaster.co.uk

Andere Handbücher für CAMON TC07

Inhaltsverzeichnis

Andere Tracmaster Rasen- und Gartengeräte Handbücher

Tracmaster

Tracmaster CAMON LS42 Bedienungsanleitung

Tracmaster

Tracmaster Camon LS14 Bedienungsanleitung

Tracmaster

Tracmaster CAMON LS17 Bedienungsanleitung

Tracmaster

Tracmaster Camon LS14 Benutzerhandbuch

Tracmaster

Tracmaster BCS630 Bedienungsanleitung

Tracmaster

Tracmaster BCS615L Bedienungsanleitung

Tracmaster

Tracmaster Camon C6 Bedienungsanleitung

Tracmaster

Tracmaster Camon LS42B1 Benutzerhandbuch

Tracmaster

Tracmaster Camon LS52 Benutzerhandbuch

Tracmaster

Tracmaster ARTIO BC65 Benutzerhandbuch

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung