Trane LonWorks TR1 Series VFD Bedienungsanleitung

Auxiliary Relay

Option Card

Installation Instructions

TR1



Series VFD

Variable Frequency Drive

175R5590

October, 2003 TR1-SVN02A-EN

The TR1 Series VFD contains dangerous

voltages when connected to line voltage.

After disconnecting from the line, wait at

least 15 minutes, 30 minutes for 550-600V

units, before touching any electrical compo-

nents. Only a competent electrician should

carry out the electrical installation. Improper

installation of the motor or the TR1 may

cause equipment failure, serious injury or

death. Follow this manual, National Electri-

cal Codes and local safety codes.

Many electronic components of the TR1

Series VFD are sensitive to Electrostatic

Discharge (ESD). Voltages so low that they

cannot be felt, seen or heard, can reduce the

life, affect performance, or completely

destroy sensitive electronic components.

When performing service, proper ESD

equipment should be used to prevent pos-

sible damage from occurring.

It is the responsibility of the user or the

person installing the TR1 Series VFD to

provide proper grounding, as well as motor

overload and branch circuit protection

according to the National Electrical Code

and local codes.

DANGER

WARNING

CAUTION

Single Relay Option Card

The ratings of the relay contacts are the same as the standard Form C relay.

Output terminals are located on the single relay option card. The terminals

are 110, 111, and 112. Input to the relay is through terminals 113 and 114,

also located on the option card. Input to the coil in the relay is 24 VDC, 10

mA nominal. The input to the relay is polarity sensitive. The Form C relay on

the option card may be driven by either the standard Form A relay or one of

the transistorized outputs.

Specifications

Auxiliary Relay Card Option Output

Terminals Function Rating

110-111-112 Relay output Form C contact (n.o. and n.c.)

240 VAC, 2 amps

24 VDC 10 mA, 24 VAC 100 mA minimum

113-114 Coil 24 VDC 10 mA nominal. Polarity

sensitive.

TR1 Series VFD Standard Output

Terminals Function Rating

01-02-03 Relay output Form C contact (n.o. and n.c.)

240 VAC, 2 amps

24 VDC 10 mA, 24 VAC 100 mA minimum

04-05 Relay output Form A contact (n.o. contact)

50 VAC, 1 amp

75 VDC, 1 amp

42-39 Analog output 0/4-20 mA analog signal (Max. 500

ohm load) or 24 VDC logic signal

(Max. 600 ohm load)

45-39 Analog output 0/4-20 mA analog signals or 24 VDC

logic signals

Remove power to drive and wait at

least 15 minutes to discharge voltage.

NEMA 1 Installation

DANGER

Position option card to back side of cassette. Slide edge of card into

slot in side of cassette. Secure option card by pressing it flush to

cassette. Insert two self-tapping screws provided in holes in upper

left and bottom center of card. Tighten to 7 in-lb. (0. 8 N-m).

NEMA 1 Installation (continued)

Back side of cassette

End view

Connect two ribbon cables. Hinge cassette from top. Reinsert screws and

tighten to 8 in-lb. (0.9 N-m). Plug in control terminal strips. Wire option card

as described in Wiring.

NEMA 1 Installation (continued)

Remove power to drive and wait at

least 15 minutes to discharge voltage.

DANGER

NEMA 12 Installation

NEMA 12 Installation (continued)

Position option card to back side of cassette. Slide edge of card into

slot in side of cassette. Secure option card by pressing it flush to

cassette. Insert two self-tapping screws provided in holes in upper

left and bottom center of card. Tighten to 7 in-lb. (0. 8 N-m).

Connect two ribbon cables. Hinge cassette from top. Reinsert screws

and tighten to 8 in-lb. (0.9 N-m). Plug in control terminal strips. Wire

option card as described in Wiring.

Back side of cassette

End view

Wiring

The single relay option card can be driven by relay 2, or by either of

the two analog outputs.

To Drive from Relay 2:

Wire as shown below. Install a jumper between terminals 5 and 12.

Program relay using parameter 326.

Output Relay 2

04 05 12 13 39 42 45 50 53 54 55 60

16 17 18 19 20 27 29 32 33

61 68 69

110

111

112

113

114

VLT 5000

Relay Option

Internal

Relay

Contacts

Tighten terminals on drive terminal strip to 5 in-lbs (0.6 N-m).

Tighten terminals on option card to 3.5 in-lbs (0.4 N-m).

TR1 VFD

Output 45

04 05 12 13 39 42 45 50 53 54 55 60

16 17 18 19 20 27 29 32 33

61 68 69

110

111

112

113

114

VLT 5000

Relay Option

Internal

Relay

Contacts

Output 42

04 05 12 13 39 42 45 50 53 54 55 60

16 17 18 19 20 27 29 32 33

61 68 69

110

111

112

113

114

VLT 5000

Relay Option

Internal

Relay

Contacts

Wiring (continued)

To Drive from Analog Output 42:

Wire as shown in figure 2 below. Program the relay using parameter 319.

To Drive from Analog Output 45:

Wire as shown in figure 3 below. Program the relay using parameter 321.

Tighten terminals on drive terminal strip to 5 in-lbs (0.6 N-m).

Tighten terminals on option card to 3.5 in-lbs (0.4 N-m).

TR1 VFD TR1 VFD

Andere Handbücher für LonWorks TR1 Series VFD

Inhaltsverzeichnis

Andere Trane Gleichstromantrieb Handbücher

Trane

Trane TR150 Bedienungsanleitung

Trane

Trane VLT AQUA Drive FC 202 VLT AutomationDrive FC... Bedienungsanleitung

Trane

Trane TR200 Series Bedienungsanleitung

Trane

Trane TR200 Series Bedienungsanleitung

Trane

Trane CVHE Bedienungsanleitung

Trane

Trane TR150 Betriebsanleitung

Trane

Trane TR200 Series Bedienungsanleitung

Trane

Trane TR200 Series Handbuch

Trane

Trane CVHE Bedienungsanleitung

Trane

Trane TR200 Series Handbuch

Trane

Trane TR150 Bedienungsanleitung

Trane

Trane Liquid-Cooled Adaptive Frequency AFDE Montage- und Bedienungsanleitung

Trane

Trane VarioTrane TR1 2800 Series Bedienungsanleitung

Trane

Trane TR200 Series Handbuch

Trane

Trane TR1 6002-6004 Bedienungsanleitung

Trane

Trane TR200 Series Betriebsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch

Lenze

Lenze 8200 vector Bedienungsanleitung