Trane GBPD Bedienungsanleitung

Discharge Air

Nozzle Kits

Library Service Literature

Product Section Air Terminal Devices & Heat Products

Product Gas Unit Heaters

Model GPND/GPPD

Literature Type Installation

Sequence 1

Date August 1997

File No. SV-TD-UH-GPND-IN-1-897

Supersedes New

Installation GPND-IN-1

Since the Company has a policy of continuous product improvement, it reserves the right to change specifications and

design without notice.

Models

GAND

GAPD

GBND

GBPD

GCND

GCPD

GEND

GEPD

GHND

GHPD

GKND

GKPD

GPND

GPPD

Sizes 100 through 400

Literature Change History

GPND-IN-1 (August 1997)

Original issue of the manual.

Warnings and Cautions

Warnings and Cautions appear at

appropriate sections throughout

this manual.

WARNINGS!

alert the installer, owner,

operator or service personnel

to potential hazards which if

not avoided could result in

death or serious personal injury.

Cautions:

alert personnel to conditions

which if not avoided may result

in minor or moderate injury.

Also alerts against unsafe prac-

tices causing equipment

damage.

Shipping Instructions

Before installing the nozzle kit, be

sure to confirm that the proper kit

has been sipped.

If a thorough inspection of the kit

reveals damage or material

shortages, file a claim with the

carrier immediately. Specify the

extent and type of damage found,

and notify the appropriate Trane

sales office. Do not install a

damaged nozzle kit without the

Trane sales representative’s

approval!

Description

The nozzle kits are used to direct

discharge air on unit heaters with

a variety of angles available.

Table of Contents

General Information ................... 2

Literature Change History ................ 2

Warnings and Cautions ................. 2

Description ........................ 2

Installation ........................ 3

30° Nozzle Kit ...................... 3

45° Nozzle Kit ...................... 4

60° Nozzle Kit ...................... 5

90° Nozzle Kit ...................... 6

5-Way Blow Down Nozzle Kit .............. 7

Y-Splitter Nozzle Kit ................... 7

General Information

2 GPND-IN-1

WARNING!

Disconnect the power source

before installing this kit to

prevent death or serious

personal injury due to

electrical shock.

For Use On Propeller and

Blower Unit Heaters

Natural or Power Vent

Kit Contents (Unassembled)

(2) Side Panels—L.H. & R.H.

(1) Top Panel

(1) Bottom Cross Brace

(1) Bag of #8 Drill Screws

The following steps for

assembling are recommended in

sequence:

1. Remove seven (7) horizontal

louvers and louver cone

springs from unit heater and

set aside. (Note louver and

spring positions).

2. Drill three (3) 1/8" diameter

holes in each unit heater “side

panel” to dimensions shown,

(see drawing).

3. Fasten L.H. (Item 1) and R.H.

(Item 2) side panels to unit

heater “side panels” with three

(3) drill screws each using

holes drilled in Step 2 above.

4. Attach “top panel” (Item 3) to

nozzle side panels (Items 1 &

2) with six (6) drill screws.

5. Fasten “top panel” (Item 3) to

heater’s “upper trim panel”

utilizing existing screws at

each end. Then, using

remaining holes as template,

drill through with 1/8" diameter

drill and fasten with drill

screws.

6. Attach and fasten “bottom

cross brace” (Item 4) with two

(2) drill screws.

7. Install six (6) of the seven (7)

louvers and louver cone

springs removed from the unit

heater in Step 1.

Installation—30° Nozzle Kit

GPND-IN-1 3

WARNING!

Disconnect the power source

before installing this kit to

prevent death or serious

personal injury due to

electrical shock.

For Use On Propeller and

Blower Unit Heaters

Natural or Power Vent

Recommended procedure for the

nozzle installation to the unit

heater:

1. Standard (Natural Vent)

Units

1. Remove the louvers and cone

springs from the discharge

end of the unit heater.

2. Remove the upper front trim

panel (located directly above

the heat exchanger opening).

3. Install the nozzle by simply

hooking the top panel flange

of the nozzle over the top

flange of the heat exchanger.

The nozzle side panels should

slide inside the heat

exchanger opening.

4. Secure the bottom of the

nozzle to the lower front trim

panel of the unit heater, by

drilling through and using the

screws provided.

2. High Efficiency (Power Vent)

Units

1. Remove the louvers and cone

springs from the discharge

end of the unit heater

2. Remove the screws from the

upper front trim panel of the

unit heater.

3. Install the nozzle by securing

the top panel of the nozzle to

the face of the upper front trim

panel, using the screws that

were just removed from each

end. The sides of the nozzle

should slide into the heat

exchanger opening.

4. Add the remaining screws in

the locations provided in the

nozzle top panel; drill through

into the unit heater trim panel.

5. Secure the bottom of the

nozzle to the lower front trim

panel of the unit heater, by

drilling through and using the

screws provided.

Installation—45° Nozzle Kit

4 GPND-IN-1

WARNING!

Disconnect the power source

before installing this kit to

prevent death or serious

personal injury due to

electrical shock.

For Use On Propeller and

Blower Unit Heaters

Natural or Power Vent

Kit Contents (Unassembled)

(2) L.H. Side Panels

(2) R.H. Side Panels

(1) 30° Top Panel

(1) 60° Top Panel

(1) Bottom Cross Brace

(1) Bag of #8 Drill Screws

The following steps for

assembling are recommended in

sequence:

1. Remove seven (7) horizontal

louvers and louver cone

springs from unit heater and

set aside. (Note louver and

spring positions).

2. Drill three (3) 1/8" diameter

holes in each unit heater “side

panel” to dimensions shown,

(see drawing).

3. Fasten L.H. (Item 1) and R.H.

(Item 2) side panels to unit

heater “side panels” with three

(3) drill screws each using

holes drilled in Step 2 above.

4. Attach “top panel” (Item 3) to

nozzle side panels (Items 1 &

2) with six (6) drill screws.

5. Fasten “top panel” (Item 3) to

heater’s “upper trim panel”

utilizing existing screws at

each end. Then, using

remaining holes as template,

drill through with 1/8" diameter

drill and fasten with drill

screws.

6. Fasten second L.H. (Item 1)

and second R.H. (Item 2) side

panels to first side panels

(Items 1 and 2) with three (3)

drill screws each.

7. Attach 60° “top panel° (Item 4)

to second nozzle side panels

(Items 1 and 2) with six (6)

drill screws.

8. Fasten rear horizontal flange

of top panel (Item 4) to front

horizontal flange of top panel

(Item 3) with drill screws.

9. Attach and fasten “bottom

cross brace” (Item 4) with two

(2) drill screws.

10.Install six (6) of the seven (7)

louvers and louver cone

springs removed from the unit

heater in Step 1.

Installation—60° Nozzle Kit

GPND-IN-1 5

WARNING!

Disconnect the power source

before installing this kit to

prevent death or serious

personal injury due to

electrical shock.

For Use On Propeller and

Blower Unit Heaters

Natural or Power Vent

Recommended procedure for the

nozzle installation to the unit

heater:

1. Standard (Natural Vent)

Units

1. Remove the louvers and cone

springs from the discharge

end of the unit heater.

2. Remove the upper front trim

panel (located directly above

the heat exchanger opening).

3. Install the nozzle by simply

hooking the top panel flange

of the nozzle over the top

flange of the heat exchanger.

The nozzle side panels should

slide inside the heat

exchanger opening.

4. Secure the bottom of the

nozzle to the lower front trim

panel of the unit heater, by

drilling through and using the

screws provided.

2. High Efficiency (Power Vent)

Units

1. Remove the louvers and cone

springs from the discharge

end of the unit heater

2. Remove the screws from the

upper front trim panel of the

unit heater.

3. Install the nozzle by securing

the top panel of the nozzle to

the face of the upper front trim

panel, using the screws that

were just removed from each

end. The sides of the nozzle

should slide into the heat

exchanger opening.

4. Add the remaining screws in

the locations provided in the

nozzle top panel; drill through

into the unit heater trim panel.

5. Secure the bottom of the

nozzle to the lower front trim

panel of the unit heater, by

drilling through and using the

screws provided.

Installation—90° Nozzle Kit

6 GPND-IN-1

WARNING!

Disconnect the power source

before installing this kit to

prevent death or serious

personal injury due to

electrical shock.

For Use On Blower Unit

Heaters

Natural or Power Vent

WARNING!

Disconnect the power source

before installing this kit to

prevent death or serious

personal injury due to

electrical shock.

For Use On Propeller and

Blower Unit Heaters

Natural or Power Vent

Use directions for 90° nozzle kit

assembly and installation.

Use directions for 90° nozzle kit

assembly and installation.

Y-Splitter Nozzle Kit

5-Way Blow Down Nozzle Kit

Installation

GPND-IN-1 7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Trane Heizung Handbücher

Trane

Trane TR250 Bedienungsanleitung

Trane

Trane BAYCCHT101AA Montageanleitung

Trane

Trane UHAA-15 Betriebsanleitung

Trane

Trane UniTrane Betriebsanleitung

Trane

Trane BAYCCHT101AA Montageanleitung

Trane

Trane UHSB Montage- und Bedienungsanleitung

Trane

Trane BAYSPEK060 Montageanleitung

Trane

Trane BAYHTR1504BRKC Montageanleitung

Trane

Trane BAYHTRV105 Montageanleitung

Trane

Trane BAYEACC25BK1B Montageanleitung

Trane

Trane Force-Flo Betriebsanleitung

Trane

Trane SRV-SVN06C-EN Bedienungsanleitung

Trane

Trane UHEC-IM-7A Wartungs- und Serviceanleitung

Trane

Trane UniTrane Montage- und Bedienungsanleitung

Trane

Trane FVAE Kurzanleitung

Trane

Trane BAYHTFB318 Series Bedienungsanleitung

Trane

Trane GANE Montage- und Bedienungsanleitung

Trane

Trane Arctic PolyTherm TP Series Montage- und Bedienungsanleitung

Trane

Trane UniTrane Fan-Coil Betriebsanleitung

Trane

Trane GKNE Betriebsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung