Transcension LED Master 64 Bedienungsanleitung

LED Master 64

Order code: BOTE04

Manual

Please read these instructions carefully before use

LED Master 64 manual

Contents

1. Features .................................................................................................................... 2

2. General Instructions.................................................................................................... 3

3. Overview

3.1 Front View ........................................................................................................ 4

3.2 Rear View......................................................................................................... 5

4. Operation Guide

4.0 Enter Programming Mode ................................................................................ 5

4.1 Channel Assignment...................................................................................... 6-7

4.2 Store Saved Colours ........................................................................................ 7

4.3 Delete Saved Colours....................................................................................... 8

4.4 Program Chase ............................................................................................. 8-9

4.5 Insert Step into a Chase .............................................................................. 9-10

4.6 Delete Step from a Chase .............................................................................. 10

4.7 Delete Chase.................................................................................................. 11

4.8 Factory Reset ................................................................................................. 11

4.9 Manual Mode.................................................................................................. 11

4.10 Run Saved Colours ...................................................................................... 12

4.11 Run CHASE............................................................................................. 12-13

4.12 Run Pre Set Colours..................................................................................... 14

4.13 Manual control.............................................................................................. 15

4.14 Strobe........................................................................................................... 15

4.15 Blackout ...................................................................................................... 15

4.16 Foot Switch (CA-8F) ................................................................................ 15-16

4.17 Update by USB drive .................................................................................... 16

4.17 Upload files to USB memory stick ................................................................ 17

4.17 Downloading files to the controller from USB memory stick ......................... 17

In the box:

1 x LED Master 64 DMX Controller

1 x Power adaptor

1 x USB gooseneck lamp

1 x Pair of 19” rack ears

1 x Manual

LED Master 64 manual

1. Features

1. The LED Master 64 is a user-friendly LED controller

2. Designed to control all LED lighting fixtures with up to 8 channels

3. Control up to 64 channels of 8 LED groups

4. 8 individual buttons for selecting 8 groups of lighting fixtures

5. LED display for easy navigation

6. 8 colour pre-set buttons

7. 6 saved colours with 4 Banks

8. 8 chases, each with up to 32 steps

9. 4 operation modes: Auto Chase, Sound Chase, Manual Control and Fade

10. Optional Foot Controller (CA-8F) for ease of operation

NOTE: Knowledge of DMX is required to fully utilise this unit.

LED Master 64 manual

2. General Instruction

Please read this manual carefully, as it includes important information regarding the units

operation, maintenance and technical data. Keep this manual with the unit for future

consultation.

WARNINGS！

Avoid any flammable liquids, water or metal objects entering the unit.

Should any liquid be spilled on the unit, DISCONNECT the power supply

to the unit immediately.

STOP using the unit immediately in the event of serious operation problems

and contact your local dealer to have the unit serviced.

DO NOT open the unit - there are no user-serviceable parts inside.

NEVER try to repair the unit yourself. Repairs undertaken by unqualified people

could cause damage or malfunction.

CAUTIONS！

After removing the packing, check that the unit is NOT damaged in any way. If in doubt,

DO NOT use the unit and contact the dealer where the item was purchased.

Packaging material (plastic bags, polystyrene foam, staples, etc) MUST NOT be

left within children's reach, as it can be dangerous.

This unit must only be operated by adults, DO NOT allow children to tamper

or play with it.

NEVER use the unit under the following conditions: excessive dryness or humidity

(ideal conditions are between 35% and 80%), vibrations or bumps, or in places with

a temperature of over 45°C/113°F or less than 2°C/35.6°F.

DO NOT dismantle or modify the unit.

LED Master 64 manual

3. Overview

3.1 Front View

1. FIXTURE SELECTOR 1-8

Use to select fixtures

2. AUTO CHASE

Run the built-in chase

3. SOUND CHASE

Run the built-in chase to the music

4. AUTO FADE

Run the built-in fade

5. MANUAL CONTROL

Press the button, for manual control

6. CHANNEL ASSIGNMENT

For channel assignment, in programme mode

7. USB PORT

Use to update software and connect a gooseneck lamp

8. PRE-SET COLOURS

For instant recall of colours

9. SAVED COLOURS

Select 24 colors by UP/DOWN button (4 banks of 6)

10. LED DISPLAY

The operation values will show on the LED display

11. PROGRAMME/RECORD

Enter or exit program/record mode

12. INSERT/TAP

Insert one step/set up a tap speed for chases

13. UP/DOWN buttons

Select bank, run chase manually, adjust the sound sensitivity and the

speed of chase auto run

14. DEL/CLEAR

Delete preset color, chase or step/clear output

15. SAVED CHASES

Use to select chase 1-8

16. FADER 1-6

Adjust the output of 1-6 channels

17. USER DEFINED FADERS

For user-defined operation

18. MANUAL/MUSIC/AUTO

When using the CA-8F to control, the corresponding LED will be on

indicating Manual Mode, Sound Mode or Auto Mode

19. BLACKOUT/FOOTSWITCH

Used for blackout and to activate CA-8F operation

20. STROBE

Activates strobe on all fixtures

21. CHASE/STROBE SPEED

Use to adjust the chase speed and set the strobe speed

22. FADE SPEED

Use to adjust the fade speed as a percentage of the run time

LED Master 64 manual

3.2 Rear View

1 POWER SWITCH

Power on/off the unit

2 POWER IN

9-12DC min 300mA

3 3pin DMX Out

3pin DMX-512 output

4 5pin DMX Out

5pin DMX512 output

○5 RJ45 CONNECTOR

RJ 45 Cable port

○6 CA-8F FOOT CONTROLLER

CA-8F connector

4. Operation Guide

When you turn on the power to the LED Master 64, it will continue

running the last function/programme from when it was previously

powered down.

4.0 Enter Programming mode

To enter the programming mode: Hold PROGRAM/REC button for

3 seconds, when the LED display shows LOCK, you should press the

fixture selector button 6 six times to unlock. That means the code is

“666666”. Then the PROGRAM/REC button LED and the LED indicator

above the saved colors button, as well as the saved chases button, will

blink indicating programme mode is active.

LED Master 64 manual

4.1 Channel Assignment

The ability to assign/patch the 8 channels of the LED Master 64 is one of its most powerful

features. This gives you the option of customising the controller to the DMX channels of your

lighting fixtures. For example: If you have a lighting fixture with the following channels:

1 – Master dimmer

2 – Red

3 – Green

4 – Blue

You can now assign/patch the controller in the following way:

Set the MASTER DIMMER fader of the controller to ‘1’

(If no dimmer channel is present, set to ‘n’)

Set the RED fader of the controller to ‘2’

Set the GREEN fader of the controller to ‘3’

Set the BLUE fader of the controller to ‘4’

Set all the remaining faders to ‘Zero’

When this has been completed the master dimmer, red, green and blue faders will now

control the fixture correctly.

Also, you will now be able to use the pre-set colours, auto chase, auto fade etc.

If the controller has been updated to V1.5 or later the user may now patch a virtual dimmer

for any fixture that does not feature its own onboard dimmer channel(i.e. 3 DMX channel

RGB fixtures).During the patch process please assign the MASTER DIMMER fader to

display ”n”, this will activate the controllers virtual dimmer function. The virtual dimmer will

then give control over intensity for all functions of control including manual colours, fades

and chases.

NOTE: If 2 or more channels are set to the same number during assignment they will flash

to indicate an error. Please ensure all channels have a different number prior to saving.

The only exception to this is ‘0’ or zero, as you can set multiple channels to zero

(no DMX output).

1. Enter programming mode

2. Press CHANNEL ASSIGNMENT button for 3 seconds, the

LED Master 64 manual

LED indicator above will light indicating the assignment mode is active.

3. Press FIXTURE SELECTOR 1-8 button to choose units.

4. Use FADER 1-8 to assign the colour etc for each channel; at

this point you can also set any unwanted channels to zero.

5. Press the PROGRAM/REC button, and all LED indicators will

blink 3 times and then go out, indicating that any changes have

been stored successfully.

6. Repeat steps 3-5 to assign all other channels for the remaining fixtures.

7. Hold PROGRAM/REC button for 3 seconds to exit programming mode.

4.2 Store Saved Colours

1 Enter programming mode.

2 Press FIXTURE SELECTOR 1-8 button to choose units.

3 Use fader FADER 1-8 to adjust the output.

4 Press PROGRAM/REC button once.

5 Press UP/DOWN button to choose bank 1-6 to store saved color

(Jump this step if you have chosen a bank before).

6 Press SAVED COLOURS button, and all LED indicatorswill blink

3 times and then go out, the corresponding LED will then be

LED Master 64 manual

blinking, indicating that it has stored successfully (when the LED

indicator is off, this means there is no colour saved).

7 Repeat steps 2-6 to store more saved colours.

8 Hold PROGRAM/REC button for 3 seconds to exit programming mode,

the LED indicator above PROGRAM/REC will go off.

4.3 Delete Saved Colors

1 Enter programming mode.

2 Use UP/DOWN button to choose bank 1-6 to save the colour into

(Jump this step if you have chosen bank before).

3 Hold DEL/CLEAR button, press SAVED COLOURS 1-6,

all LEDs will blink 3 times and then go out, the corresponding

LED will then go off, indicating the saved colour has been

deleted successfully.

4 Repeat 2-3 steps to delete more colour presets.

5 Hold PROGRAM/REC button for 3 seconds to exit programming

mode, the LED above PROGRAM/REC button will go off.

4.4 Program Chase

1 Enter programming mode.

2 Press CHASE 1-8 button to choose chase

which you want to store in.

3 Press FIXTURE SELECTOR 1-8 button to choose units,

using fader 1-8 to adjust the light effect, or open a

previously saved colour.

LED Master 64 manual

4 Press PROGRAM/REC button, all LEDs will blink 3 times and then go out indicating

that one step has stored successfully (it will show ‘NULL’ and will not store if all

outputs are ‘0’).

5 Repeat steps 3-4 to store more steps, each chase can store 32 steps maximum,

it will show “FULL” when up to 32 steps.

6 Repeat steps 2-5 to store more chases.

7 Hold PROGRAM/REC button for 3 seconds to exit programming mode,

the LED indicator above PROGRAM/REC will go off.

ATTENTION: Before using any saved color or lighting effect, press DEL/CLEAR button

to clear any output you set inadvertently, so that you can avoid storing any unwanted

lighting effect.

4.5 Insert Step to Chase

1 Enter programming mode.

2 Press CHASE 1-8 button to choose the desired chase

to insert step.

3 Press INSERT/TAP button, the LED indicator above it will go on,

the present step will show on the display (for example, it will

show ‘ST00’ when there is no step).

4 Use UP/DOWN button to select the position of inserted steps

(If you want to insert a fifth step, you should set the present step

to be ‘ST05’).

5 Press FIXTURE SELECTOR 1-8 button to choose fixture, use

UP/DOWN button to choose saved color or push the FADER 1-8

to adjust the lighting effect.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Transcension Stromverteilungseinheit Handbücher

Transcension

Transcension HS2 Hybrid Distribution Splitter Bedienungsanleitung

Beliebte Stromverteilungseinheit Handbücher anderer Marken

hager

hager SP 015 Bedienungsanleitung

Pakedge

Pakedge PowerPak 9 Bedienungsanleitung

Pts

Pts 9042 Series Bedienungsanleitung

Shure

Shure WA405 Bedienungsanleitung

CORNING

CORNING CCH 4U Bedienungsanleitung

Panamax

Panamax M4LT-EX Bedienungsanleitung

PANCONNECT

PANCONNECT FLAT 3M Bedienungsanleitung

Raytheon

Raytheon 138-118 Bedienungsanleitung

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Bedienungsanleitung

Botex

Botex PSA 322-6 DL Bedienungsanleitung

GE QuiXtra 4000 Kurzanleitung

RDL

RDL EZ Series Bedienungsanleitung

StarTech.com

StarTech.com RKPW161915 Systemhandbuch

Vertiv

Vertiv Knürr DI-Strip Rack PDU Bedienungsanleitung

ABB

ABB PSBS0065 Handbuch

Baumuller

Baumuller BFN 3-1-0007-001 Handbuch

Eaton

Eaton StructuredWiringSolutions ESWT41600 Handbuch

GE GEK-45404F Bedienungsanleitung