Transcension UP2 TRUEDIM Bedienungsanleitung

Order code: BOTE39

OUTPUT: 10A Max.

UP2 TRUEDIM 1CH DIMMER

DMX

HTP

UP2 TRUEDIM

1 Channel Dimmer

User Manual

www.prolight.co.uk UP2 TRUEDIM 1 Channel Dimmer User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available voltage is 240V AC~50Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• WARRANTY: One year from date of purchase.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

www.prolight.co.uk UP2 TRUEDIM 1 Channel Dimmer User Manual 3

Product overview & technical specications

This convection cooled dimmer features 16A and powerCON TRUE1 outputs and is perfect for using with

standalone xtures in small studios, for follow spots or for incorporating into and expanding DMX systems.

Suitable for use with incandescent loads when used as a switch pack.

• Compact, 1 channel DMX/HTP dimmer pack

• Dim preset - Dim limiter

• HTP function

• Can be congured as a switch pack

• Easy-to-use mounting bracket

• PowerCON TRUE1 input/output

• 5-Pin XLR input/output

• Output connectors:

1 x 16A & 1 x powerCON TRUE 1

• Maximum output:

10A resistive

5A inductive

• Trailing edge dimming technology

UP2 TRUEDIM 1 Channel Dimmer

Specications UP2 TRUEDIM Dimmer

Power supply 240V, 50Hz

Fuse F10A 250V

Dimensions 218 x 148 x 133mm

Weight 1.7kg

Order code BOTE39

01 - 16A output

02 - powerCON TRUE 1 output

03 - LED display

04 - HTP fader

05 - Function buttons

06 - PowerCON TRUE1 input

07 - PowerCON TRUE1 output

08 - Fuse F10A 250V

09 - 5-Pin XLR DMX input

10 - 5-Pin XLR DMX output

11 - DMX indicator

In the box:

1 x controller,

1 x power cable

& 1 x user manual

Warning: This unit must be earthed.

CAUTION!

Risk of Electric Shock

DO NOT OPEN

Fuse: F10A 250V

5 x 20mm

POWER INPUT:

AC 240V~50Hz

10A Max.

POWER OUTPUT:

AC 240V~50Hz

DMX INPUT DMX OUTPUT

0908

06 10

OUTPUT: 10A Max.

UP2 TRUEDIM 1CH DIMMER

DMX

HTP

OUTPUT: 10A Max.

UP2 TRUEDIM 1CH DIMMER

DMX

HTP

www.prolight.co.uk UP2 TRUEDIM 1 Channel Dimmer User Manual 4

Operating instructions

When the unit is powered up the unit will show

the DMX address that the unit was last in before

it was powered down. If the DMX address 123

was selected in the units last use the unit will

display “A123”.

By using the “UP” or “DOWN” buttons the user

is able to select the required DMX address.

Once the DMX address is selected, it will be

automatically stored into the units memory.

Press the “MENU” button until

the display shows d---.

Press the “UP” or “DOWN”

button so the display shows

S---.

Press the “MENU” button to

enter switch pack mode. Use

the “UP” or “DOWN” buttons

to change between S-on

and S-oF.

Press the “MENU” button to exit switch pack mode. In Switch pack

on mode the output is on and the xture will illuminate

regardless of the DMX signal. In switch pack off mode the output is

turned off and the xture is controlled via the DMX signal. If the DMX

level is less than 40% the xture will blackout, above 40% the xture

will illuminate.

DMX address mode:

Switch pack mode:

--- ---

www.prolight.co.uk UP2 TRUEDIM 1 Channel Dimmer User Manual 5

Operating instructions

Dimmer pack mode:

Press the “UP” or “DOWN”

button so the display shows

d---.

---

Press the “MENU” button to

enter Dimmer limit mode.

Use the “UP” or “DOWN”

buttons to change the value

between 10-100.

Use the “UP” or “DOWN”

buttons to change the value

between 00-100. Once the

dimmer preset is selected it

will be automatically stored

into the units memory.

Please note: The HTP Fader MUST be at value 0 for the DMX to operate correctly.

Press the “MENU” button exit

out of any of the above options.

Press the “MENU” button to

enter Dimmer preset mode.

www.prolight.co.uk UP2 TRUEDIM 1 Channel Dimmer User Manual 6

Setting the DMX address:

The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”

from 1- 512. A xture requiring one or more channels for control begins to read the data on the channel

indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was

addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104,

105 and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in

the chain starts at 107.

DMX 512:

DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent

xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.

DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”

XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).

DMX linking:

DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest

cable path possible. The order in which xtures are connected in a DMX line does not inuence the

DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in

a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a

DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,

no matter where it is located in the DMX chain.

DATA cable (DMX cable) requirements (for DMX operation):

This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.

Your unit requires either a standard 3-pin or 5-pin XLR connector for data input/output, please check

the xtures specications as to which your unit accepts.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight Concepts dealers.

Please quote: CABL10 – 2m CABL11 – 5m CABL12 – 10m3-Pin:

CABL185 – 2m CABL187 – 5m CABL188 – 10m5-Pin:

www.prolight.co.uk UP2 TRUEDIM 1 Channel Dimmer User Manual 7

Notice:

Be sure to follow the diagrams below when making your own cables.

Do not connect the cables shield conductor to the ground lug or

allow the shield conductor to come in contact with the XLRs

outer casing. Grounding the shield could cause a short circuit

and erratic behaviour.

Line termination:

When longer runs of cable are used,

you may need to use a terminator on

the last unit to avoid erratic behaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL90,

5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a

3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.

5-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

Termination reduces signal

transmission problems and

interference. It is always

advisable to connect a DMX

terminal, (resistance 120

Ohm 1/4W) between pin 2

(DMX-) and pin 3 (DMX+) of

the last xture.

5-Pin

2 4

3-Pin

1 2

Pin Conguration

3-Pin 5-Pin

Pin 1 - Ground

Pin 2 - Negative

Pin 3 - Positive

– Pin 4 - N/C

– Pin 5 - N/C

DMX 512

3-Pin XLR output

DMX 512

3-Pin XLR input

GROUND

DMX +

DMX –

DMX 512

5-Pin XLR output

DMX 512

5-Pin XLR input

GROUND

N/C

DMX –

N/C DMX +

1 ground

3 hot

2 cold

3-Pin XLR male 3-Pin XLR female

2 cold

3 hot

1 ground

2 cold

1 ground 5 N/C

3 hot 4 N/C

5-Pin XLR male 5-Pin XLR female

4 N/C

5 N/C 1 ground

3 hot 2 cold

www.prolight.co.uk UP2 TRUEDIM 1 Channel Dimmer User Manual 8

WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed of

with other household wastes at the end of its working life. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, please separate this from other

types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their

local government ofce, for details of where and how they can take this item for environmentally

safe recycling.

Business users should contact their supplier and check the terms and conditions of the

purchase contract. This product should not be mixed with other commercial wastes for disposal.

Inhaltsverzeichnis

Andere Transcension Schalten Handbücher

Transcension

Transcension PC 08 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung