TransCore AP4119 Bedienungsanleitung

Trusted Transportation Solutions

P/N 16-4119-001 Rev B 3/2023

AP4119 Rail Tag

Programmer

User Guide

The AP4119 Rail Tag Programmer User Guide provides information necessary for

installing, operating, and troubleshooting the AP4119 Rail Tag Programmer.

This Guide describes the proper setup and operation of the AP4119 Rail Tag Programmer and provides

procedures useful for troubleshooting problems encountered after installation.

The AP4119 Rail Tag Programmer User Guide is designed to be used by technical personnel responsible

for setting up and operating the AP4119 Rail Tag Programmer and related software.

Figure 1 AP4119 Rail Tag Programmer

AP4119 Rail Tag Programmer User Guide

TransCore Proprietary

trademarks and are used under license. All other trademarks listed are the property of their respective

owners. Contents subject to change. Printed in the U.S.A.

For further information, contact:

TransCore

8600 Jeerson Street NE

Albuquerque, NM 87113 USA

Web: www.transcore.com

TransCore Technical Support

Phone: (505) 856-8007

email: [email protected]

TransCore Proprietary iii

WARNING TO USERS IN THE UNITED STATES

FCC RADIO FREQUENCY INTERFERENCE STATEMENT

47 CFR §15.105(A)

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency (RF) energy and

may cause harmful interference to radio communications if not installed and used in accordance

with the instruction manual. Operating this equipment in a residential area is likely to cause harmful

interference, in which case, depending on the regulations in eect, the users may be required to

correct the interference at their own expense.

NO UNAUTHORIZED MODIFICATIONS 47

CFR §15.21

CAUTION: This equipment may not be modiﬁed, altered, or changed in any way without

permission from TransCore, LP. Unauthorized modiﬁcation may void the equipment

authorization from the FCC and will void the TransCore warranty.

USE OF SHIELDED CABLES IS REQUIRED

47 CFR §15.27(A)

NOTE: Shielded cables must be used with this equipment to comply with FCC regulations.

TRANSCORE, LP

USA

AP4119 Rail Tag Programmer User Guide

TransCore Proprietary

Table of Contents

Chapter 1 Programmer Basics ............................1–7

Factory Supplied and Optional Equipment ..................................1–7

Preventing Electrostatic Discharge Damage ................................1–8

Connecting to a Host Device..............................................1–9

AP4119 Host Software...................................................1–11

Chapter 2 Conﬁguring the Programmer ................. 2–13

Permissions .......................................................... 2–13

PT5780 Permissions Tag ............................................... 2–13

AAR Tag Programming ................................................. 2–16

Generic/Non-AAR Tag Programming ......................................2–17

Chapter 3 Operating the Programmer ................... 3–18

Before You Program Tags............................................... 3–18

Indicator Lights ....................................................... 3–19

Sign-On .............................................................. 3–19

Command Execution Protocol........................................... 3–19

Serial Command Set ...................................................3–20

Programming a Tag....................................................3–25

Verifying Tag Data .....................................................3–26

Security Characters....................................................3–26

Regulatory Region .....................................................3–27

Chapter 4 Troubleshooting ............................ 4–31

Appendix A Tag Programmer Speciﬁcations..............A–32

Appendix B RS–232 Connector Pin-outs.................B–33

Appendix C 6-Bit ASCII Format.........................C–34

Appendix D 4-Bit ASCII Hex Codes .....................D–35

Appendix E Programmer Response Codes ...............E–36

Appendix F Security Characters ........................F–38

Appendix G Commands ...............................G–39

TransCore Proprietary v

List of Figures

Figure 1 AP4119 Rail Tag Programmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

Figure 2 Programming Workstation with ESD Controls . . . . . . . . . . . . . . . . . . . . . . 1–8

Figure 3 RS–232 and USB Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–9

Figure 4 Host Software Installer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11

Figure 5 Label Printer and USB Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11

Figure 6 Tag Programming Host Software Screen . . . . . . . . . . . . . . . . . . . . . . . . 1–12

Figure 7 Permissions Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–13

Figure 8 AP4119 Tag Programmer LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2–14

Figure 9 Permissions Tag Being Slid into Tag Holder . . . . . . . . . . . . . . . . . . . . . . . 2–15

Figure 10 AP4119 Rail Tag Programmer Indicator Lights . . . . . . . . . . . . . . . . . . . . . 3–19

Figure 11 Tag Being Slid into Tag Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–25

Figure 12 Programmer Adapter and AT5549 EOT Tag Being Slid into Tag Holder. . . . . . . 3–28

AP4119 Rail Tag Programmer User Guide

TransCore Proprietary

List of Tables

Table 1 Accessory Kit P/N 19143-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7

Table 2 PC Interface Protocol Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–10

Table 3 Data format code, AP4119 handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–16

Table 4 Rail tag Page 3 layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–17

Table 5 List of Regional Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–28

Table 6 Region Codes and Operating Frequency Hop Set. . . . . . . . . . . . . . . . . . . . 3–29

Table 7 Troubleshooting Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . 4–31

Table 8 AP4119 Rail Tag Programmer Physical and Environmental Speciﬁcations . . . . . . . A–32

Table 9 RS–232 Connector Pin-outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B–33

Table 10 6-Bit ASCII Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–34

Table 11 4-Bit ASCII Hex Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–35

Table 12 Programmer Response Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E–36

Table 13 Permission File Download Responses . . . . . . . . . . . . . . . . . . . . . . . . . .E–37

Table 14 Permissions Tag Download Responses . . . . . . . . . . . . . . . . . . . . . . . . . E–37

Table 15 ASCII Security Characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F–38

Table 16 Serial Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G–39

Chapter 1 Programmer Basics

TransCore Proprietary 1–7

Chapter 1 Programmer Basics

This chapter lists the factory-supplied and optional equipment for the AP4119

programmer, and describes how to prevent electrostatic discharge (ESD) damage

to tags, connect to a host device, and install the optional tag programming software

to the host computer.

Factory Supplied and Optional Equipment

The programmer is shipped with the items listed. Make sure all of the items are included when unpacking

the order:

• AP4119 Rail Tag Programmer

• Programmer Accessory Kit P/N 19143-01 (Table 1)

Table 1 Accessory Kit P/N 19143-01

Accessory Kit Item Qty

(ea)

Power transformer and cable to convert AC voltage to 24 VDC 1

Power cord 1

Programmer-to-PC RS–232 connecting cable 1

Programmer-to-PC USB Type A Cable 1

Static-suppression wrist strap with cord 1

TransCore USB ﬂash drive with AP4119 Tag Programmer Host Software 1

AP4119 Programmer User Guide 1

If any of the items in Table 1 are missing from the order, contact the TransCore distributor.

Note: The AT5549 End-of-Train Tag requires a Programmer Adapter (P/N 20-4119-001) in order to

seat the AT5549 tag during programming. This adapter is an optional purchase item.

The AP4119 requires a host computer system such as a PC or communications terminal for operation.

TransCore does not supply this equipment for the AP4119 Rail Tag Programmer.

AP4119 Rail Tag Programmer User Guide

TransCore Proprietary

1–8

Preventing Electrostatic Discharge Damage

Caution

TransCore tags are sensitive to ESD, and precautions are necessary to ensure proper tag

programming operation. Use the grounded ESD static-suppression wrist strap when using the

programmer. Additional protection from ESD is recommended where practical.

Static is generated by friction. Some causes of static include the following:

• Shoes moving across a carpeted or plastic ﬂoor

• Hot air blowing into a room from a hot-air duct

• Rubbing tags together

• Rubbing tags across a tabletop

• Wearing certain types of clothing

ESD may cause signiﬁcant damage to the tag and will adversely aect a tag’s operating performance.

Typical symptoms of ESD include the following:

• Inability to program the tag

• Greatly reduced operating range

• Tag operating failure

Anti-static Workstation

In a factory or ﬁxed indoor environment, position the programmer in an anti-static workstation. Well-

designed workstations use a system of multiple precautions against ESD. Figure 2 shows an anti-static

workstation.

Contact TransCore Technical Support with any questions concerning the suitability of the programming

station or environment.

Take precautions to prevent ESD from aecting programming operations. A list of some of the most

eective precautions follows. The potential for ESD damage decreases when two or more precautions are

used together.

Figure 2 Programming Workstation with ESD Controls

Chapter 1 Programmer Basics

TransCore Proprietary 1–9

ESD Wrist Strap

Caution

Always attach the ESD wrist strap before beginning programming operations in any setting.

1. Be sure the programmer is connected to an earth ground.

2. Connect the banana plug of the ESD wrist strap to the ESD jack on the front of the unit.

3. Attach the ESD strap to your wrist.

Antistatic Mat

The anti-static work mat on which the programmer sits should be connected to earth ground through the

standard 1 M-Ohm resistance that should be provided with the mat. The mat also should be clean and free

of any electrical path to direct earth ground.

Ionized Air Blower

An ionized air blower may be set up at the workstation to provide additional ESD protection. Ionized air

blowers neutralize tags from static build-up before programming.

ESD-Safe Tags Container

Keep tags in the original box on an anti-static mat or within an ESD-safe container until they are

programmed. Grounded metallic containers are best for inhibiting ESD.

Connecting to a Host Device

The programmer requires connection to a host device — a host computer or communications terminal —

for normal operation. Figure 3 shows the RS-232 and USB connectors from the programmer to the host.

For RS–232, if the host system is a PC or a communications terminal, a null modem is not needed.

The tag programmer’s PC interface complies with the RS–232 and USB standard for data terminal

equipment and uses the protocol settings listed in Table 2. Refer to Appendix B for speciﬁcations of the

programmer’s RS–232 pin-outs.

HW-0341C

Figure 3 RS–232 and USB Connectors

AP4119 Rail Tag Programmer User Guide

TransCore Proprietary

1–10

Table 2 PC Interface Protocol Settings

Protocol Setting

Data Rate 9600 bps

Data Bits 8

Parity None

Stop Bits 1

Software Flow Control None

Hardware Flow Control None

Download USB Drivers

Before using the AP4119 programmer with a USB connection, the proper drivers may need to be installed

on the host computer. The USB drivers can be installed during the AP4119 Host installation process (“Rail

Tag Programmer Host Software” on page 1–11). Alternatively, the FTDI USB drivers can be manually

installed by following the next steps:

1. Connect the USB cable from the USB port at the back of the AP4119 to one of the host computer’s USB

ports.

2. Allow the device driver to be detected and installed automatically. If the device driver fails to

automatically load, disconnect the AP4119 from the host computer.

3. Locate and download the device driver setup executable ﬁle for your operating system from https://

ftdichip.com/drivers/

Detailed installation guides can be found here: https://ftdichip.com/document/installation-guides/.

4. Launch the downloaded software and follow the steps to install the driver.

5. Reconnect the AP4119 and allow it to be detected by the operating system.

Note: While any hyperlinks included in this section were valid at the time of publication, TransCore

cannot guarantee their long term validity.

Connect the programmer to the host computer

1. Connect the RS–232 or USB cable from the unit to the host computer system.

2. Switch on power to the programmer. The POWER then READY LEDs should illuminate. When the

READY LED illuminates, begin using the tag programmer. The tag programmer has factory default

settings installed to allow tag reads only.

To conﬁgure the tag programmer for your tag requirements, use a PT5780 permissions tag or

License Certiﬁcate (requires AP4119 Host Software) to program speciﬁc operational and security

information into the programmer. “Chapter 2 Conﬁguring the Programmer” on page 2–13 instructs

the user in conﬁguring the tag programmer using the permissions tag.

If the READY LED does not illuminate or if the host system cannot communicate with the tag

programmer, refer to “Chapter 4 Troubleshooting” on page 4–31.

Inhaltsverzeichnis

Andere TransCore Hauptplatine Handbücher

TransCore

TransCore AP4118 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung