Transient Modules 4R Handbuch
Transient Modules 4R DIY build manual - Version 1.0
Hello!
This guide is for building the 4R module from Transient Modules.
Since it is a 2HP module, it's slightly tricky to assemble. Take it easy, and
even if you're an experienced DIYer, please read ALL the steps thoroughly
before starting, as some of them are crucial and others not so obvious.
The 4R kit consists of two boards and all the parts comes in one bag.
See the lists below to identify each one of them easily before start building.
Thru Hole Parts Qty Thru hole Parts Qty SMD Parts Qty
Resistors: Regulators: Diodes:
Resistor 100K 2 7805 1 1N5819 2
Resistor 10K 18
Resistor 1K 8 Transistors: Ics:
Resistor 24K9 4 2N3904 2 TL074 2
Capacitors: Others: Pre-soldered parts:
100nF 5 LEDs bicolor 4 Atmega328P-AU 1
22pF 4 Jack socket 6 LM321 4
10uF electrolytic 2 Knurled nuts 6 MCP4728 1
Jumper 2 Resistor 4.7K 3
Others: Panel 1 Resistor 10K 1
3 pin header male 7 Bottom PCB 1 Crystal 1
Power connector 1 Top PCB 1 100nF capacitor 2
Ribbon cable 1 Silver screws 2 Ferrite 1
ʕ•ᴥ•ʔ
Transient Modules 4R DIY build manual - Version 1.0
!"#$%&'(#')*#+,-#./'0#,#+012#03#
40/',./*3"#5).6#%,7*6#.'#%84)#*,6.*3#'0#
&.47#')*#&,3'6#,6#(08#/**9#')*%#,/9#
(08:3*#,#20'#2*66#2.7*2(#'0#206*#,/(')./-"
;"#<*'=6#6',3'#1.')#')*#>?@#&,3'6A#
>029*3#')*#BC#TL074#DE6"#F06.'.0/#')*%#
1.')#the line#0/#')*#'0&#G,4*#0G#')*#5<!HI
,'#')*#6,%*#*/9#,6#the circle#./#')*#
6.27643**/J#,6#6)01/#./#')*#.%,-*6"#
TIP for SMD soldering:
http://bit.ly/2pPBRyx
B"#>029*3#')*#BC#1N5819#9.09*6"#
NOTE! K3.*/','.0/#.6#vital.#5)*#-3*( line#
0/#')*#9.09*#L4,')09*M#6)0829#%,'4)#')*#
6.27643**/J#,6#6)01/#./#')*#&.4'83*"
Close up photo of the diodes showing the line
and the orientation they must have on the board.
Depending on the source of light it may be harder
to see the line.
N"#>029*3#')*#;OC#10K 3*6.6'036"
Colour code: brown, black, black, red, brown.
Transient Modules 4R DIY build manual - Version 1.0
I"#>029*3#')*#OC#1K#3*6.6'03"
Colour code: brown, black, black, brown, brown.
P"#>029*3#')*#IC#24K9#3*6.6'03"
Colour code: red, yellow, white, red, brown.
Q"#>029*3#')*#BC#100K 3*6.6'036"
Colour code: brown, black, black, orange, brown.
H"#>029*3#')*#PC#100nF#4,&,4.'036J#
2,+*22*9#;!I"
O"##>029*3#')*#IC 22pF#4,&,4.'036J#
2,+*22*9#BB;"
R"#S*/9#')*#2*-6#0G#')*#BC#10uF#
*2*4'302('.4#4,&,4.'036#,6#6)01/#0/#')*#
&.4'83*#,/9#6029*3#')*%"
NOTE! Orientation is vital. The long leg
should be positioned in the pad marked
with the + symbol.
Transient Modules 4R DIY build manual - Version 1.0
;!"#>029*3#')*#BC#2N3904#'3,/6.6'036"#
<,+*22*9#5;J#5B"
NOTE! Make sure you place this part as
low as possible. Push down the transistor
until it's completely sitting on the PCB,
like shown in the image.
;;"#>029*3#')*#7805#3*-82,'03"#<,+*22*9#
HO!P"
NOTE! Make sure you place this part as
low as possible too. Push down the
regulator until it's completely sitting on
the PCB, like shown in the image.
;B"#F2,4*#')* power header. D'#),6#'0#+*#
&06.'.0/*9#+*'1**/#')*#FES#,6#6)01/#./
')*#&.4'83*"#
?,7*#683*#.'=6#R!T#'0#')*#FES#+*G03*#
6029*3./-"
TIP: (in the photo) you can put a small amount of
solder on any pad before placing the header. It
will help to keep it attached to the board while
you move it to ensure it is 90º and during solder
process.
Transient Modules 4R DIY build manual - Version 1.0
;N"#U*,9*36#'.%*A#5,7*#B#0G#')*% ,/9#
&86)#')*#+2,47#&2,6'.4#&,3'#,22#')*#1,(#
901/#,6#6)01/#0/#')*#V36'#.%,-*"#
F2,4*#')*#BC#jumpers#0/#')*#)*,9*36#./#
')*#&06.'.0/#6)01/#0/#')*#6*40/9#.%,-*#
,/9#6029*3 ')*% */683./-#')*(=3*#6.''./-#
40%&2*'*2(#0/#')*#FES"#
@0/='#G03-*'#'0#48'#')*#2*-6#0/#')*#0')*3#6.9*#0G#
')*#FES#,G'*3#6029*3./-A
;I"#5)*#)*.-)#0G#')*#P#3*%,././-#)*,9*36#
,260#/**96#'0#+*#,9W86'*9X
Y6./-#')*#6%,22#FESJ#&2,4*#')*#)*,9*3#
8/9*3#.'#,/9#&86)#901/#')*#+2,47#&2,6'.4#
&,3'#8/'.2#.'#3*,4)*6#')*#FESJ#,6#6)01#./#
')*#.%,-*"#Z*&*,'#').6#&304*66#G03#,22#')*
)*,9*36"
;P"#K/4*#(08=[*#')*#)*.-)#0G#')*#)*,9*36
,9W86'*9J#&2,4*#')*#P#0G#')*%#on the top
side#0G#')*#+0,39#,/9 6029*3#*/683./-#
')*(=3*#R!T#'0#')*#FES"
@0/='#G03-*'#'0#48'#')*#2*-6#0/#')*#0')*3#6.9*#0G#
')*#FES#,G'*3#6029*3./-A
;Q"#\01#')*#6%,22#+0,39A#],6'#0/*"#].36'J#
&2,4*#,22#')*#W,476#,/9#<$@6"
NOTE! Orientation of the leds is vital.
The long leg should match the + symbol
of the silkscreen!
;H"#F2,4*#')*#G30/'#&,/*2J#1).4)#.6#
6(%%*'3.4J#60#%,7*#683*#(08=3*#&2,4./-#
.'#')*#3.-)'#1,(X#')*#20-0#0/#')*#&,/*2#),6
'0#%,'4)#')*#6.9*#0G#')*#FES#1)*3*#')*#
2,6'#2*-#.6#40//*4'*9#'0#-308/9"
F2,4*#')*#Q#7/832*9#/8'6#0/#')*#W,47#
6047*'6#,/9#%,7*#683*#')*#2*96#,3*#./#
&06.'.0/J#')308-)#')*#)02*6#0G#')*#&,/*2"#
######
Transient Modules 4R DIY build manual - Version 1.0
;O"#\01#(08#4,/#6029*3#,22#')*#<$@6#,/9#
W,47#6047*'6"#K/4*#V/.6)*9J#48' ALL#')*#
2*-6X#')*#0/*6#0G#')*#<$@6#,/9#,260#')*#
2.''2*#0/*6#0G#,22#')*#W,47#6047*'6A
;R"#^0./#+0')#FES6"#>029*3#W86'#0/*#2*-#
0G#,/(#)*,9*3#,/9#4)*47#'),'#')*#+0,396#
,3*#R!T"#DG#60J#6029*3#')*#3*6'#0G#')*#2*-6"#
DG#/0'J#)*,'#'),'#2*-#'0#3*4'.G(#')*#,/-2*#
8/'.2#')*(=3*#40%&2*'*2(#&*3&*/9.482,3"
NOTE!!! >./4*#')*#6%,22#FES#.6#,260#
6(%%*'3.4J#4)*47#'),'#(08#90/='#&2,4*#.'#
8&6.9*#901/X#')*#20-0#0/#')*#&,/*2#%86'#
+*#0/#')*#6,%*#*/9#,6#')*#&01*3#
)*,9*3"
K&'.0/,2X#(08#4,/#48'#')*#&./6#0G#')*#
)*,9*36#,G'*3#6029*3"
B!"#E0//*4'#')*#3.++0/#4,+2*"#5)*#3*9#
6'3.&*#0/#')*#4,+2*#%86'#2./*#8.')#')*#
Z$@#./9.4,'.0/#0/#')*#%0982*:6#&01*3#
40//*4'03"#_/9"""
X#M##########?0982*#V/.6)*9A##########X#M
#>*'#+0')#W8%&*36#0/#SDFK<_Z#,/9
&01*3#8&#')*#%0982*A
@0/='#&,'4)#,/(')./-#(*'X#.G#,/(#0G#')*
2*96#.6#too#+3.-)'J#60%*')./-#.6#130/-
1.')#')*#%0982*"#5,7*#.'#08'#0G#')*#4,6*
,/9#13.'*#86#'0#V/9#1),'#),&&*/*9A#
DG#.'#20076#-009#,G'*3#&01*3#8&J#&,'4)#,
42047#6.-/,2#'0#5ZD`;#./&8'#,/9#4)*47
'),'#,22#')*#2*96#4),/-*#')*#40203#,6#1*22
,6#')*#[02',-*#0/#')*#G083#08'&8'6"
Transient Modules 4R DIY build manual - Version 1.0
Something is not working as it should? *
Did you like the build manual? *
Had problems during the build process? *
Do you have any suggestions to make the build process better? *
Are you missing any part? *
Were you soldering slighlty drunk and did a mess? *
* Based in real e-mails.
Then, write us!
If everything went fine: congratulations and enjoythe module!
Andere Transient Modules Steuereinheit Handbücher
Transient Modules
Transient Modules 2M Handbuch
Transient Modules
Transient Modules u3A Handbuch
Transient Modules
Transient Modules u1P Bedienungsanleitung
Transient Modules
Transient Modules u2X Handbuch
Transient Modules
Transient Modules 8S Handbuch
Transient Modules
Transient Modules 1F Bedienungsanleitung
Transient Modules
Transient Modules 2M Bedienungsanleitung
Transient Modules
Transient Modules 4R Handbuch
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
