Transpak GENESIS HORI TP-502MH Leitfaden

Original Instruction

TP-502MH

PALLET

TP-502MH

TP-502MHB (with battery)

SEMI-AUTO

GENESIS HORI

04/2018

CONTENTS

PART I

1. General Safety Instructions ................................................................. A1

2. Construction and Units ........................................................................ A4

3. General Safety Remarks ...................................................................... A6

4. Machine Information ........................................................................... A9

5. Operating the Machine ...................................................................... A20

6. Adjustment ........................................................................................ A23

7. Maintenance ...................................................................................... A25

8. Troubleshooting Guide ...................................................................... A30

PART II

1. Wiring Diagram .................................................................................... B1

PART III

1. Strapping Head Unit ………………………...………………………C1

2. Base Group ……………………………………………..………….C33

3. Reel Control Group ………………………………………………..C39

4. Body Frame Group ………………………………………………...C43

5. Electric Control Unit ……………………………………..………..C47

6. Battery Group ………………………………………..…………….C57

PART I

-A1-

1. General Safety Instructions

THIS MANUAL GIVES YOU INFORMATION ON SAFETY INSTRUCTIONS,

SPECIFICATIONS, OPERATION AND MAINTENANCE OF STRAPPING

MACHINES.

BEFORE OPERATING OR SERVICING THE MACHINE, PLEASE REVIEW

THE ENTIRE MANUAL AND FOLLOW THE SAFETY INSTRUCTIONS

CAREFULLY.

(1) Before Operating

a. Verify that the power line voltage is correct.

b. The machine must be properly grounded to avoid a shock hazard. All wiring must be in

accordance with local wiring standards.

c. The strapping machine can only be operated with polypropylene (P.P.) strapping; do not

use polyester (PET) strapping or polyethylene (PE) cord strap.

(2) During Operation

a. The lowest strapping position of the package should not be less than 175mm (6.88”).

b. Check if the machine emits any smokes or unusual sound when it is running.

(3) After operating

a. Remove dust and dirt from the unit.

b. Turn off the power when the machine is not in use.

-A2-

(4) Signs and Symbols

Symbol

Meaning

Warning for dangerous voltage!

Contact with live electrical parts will

result in severe injury or death.

Warning for hot surface!

Welding area is approximately 270oC(520℉)

Allow sufficient time for the heater to cool

down before any work in welding area.

Warning for danger!

Do not step into the machine below.

Warning for danger!

Do not put your hand below the moving

unit.

-A3-

(5) Maintenance

a. Turn off the power before removing either of the covers.

b. Use the correct tools and parts to repair the machine.

c. The heater tongue is very hot; do not touch it.

(6) Storage

a. The store room must be dry.

b. Do not expose the machine to extreme cold or hot environment.

c. Place the machine on an even floor in order to avoid any distortion.

(7) Other Reminders

a. An operation manual must remain attached to the machine at all times.

b. Do not alter the equipment or circuitry unless authorized to do so by the manufacturer.

c. Do not operate the machine with the covers removed.

d. Never put any part of your body near, under or into a moving machine.

e. Do not overload the machine by exceeding the performance limitations specified in this

manual.

-A4-

2. Construction and Units

a. TP-502MH

4 Body frame group

3 Reel control group

Holds the strap coil.

(If the reel core size is 280mm,

you can take off the center

drum to have core size 200mm.)

1 Strapping head unit

This unit is the most important

part of the machine for cutting

and sealing P.P. strap.

2 Base group

5 Electric control unit

-A5-

b. TP-502MHB

4 Body frame group

2 Base group

5 Electric control unit

6 Battery unit

3 Reel control group

Holds the strap coil.

(If the reel core size is 280mm,

you can take off the center

drum to have core size 200mm.)

1 Strapping head unit

This unit is the most important

part of the machine for cutting

and sealing P.P. strap.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Transpak Verpackungsanlagen Handbücher

Transpak

Transpak TP-6000-3 Leitfaden

Transpak

Transpak TP-6000-1 Leitfaden

Transpak

Transpak Genesis TP-501 Bedienungsanleitung

Transpak

Transpak MERCURY TP-702-59 Betriebsanleitung

Transpak

Transpak MINI-VERTI TP-202MV Leitfaden

Transpak

Transpak Atlantis TP-701 Bedienungsanleitung

Transpak

Transpak TP-6000 Bedienungsanleitung

Transpak

Transpak TP-201 Leitfaden

Transpak

Transpak TP-201 Bedienungsanleitung

Beliebte Verpackungsanlagen Handbücher anderer Marken

U-Line

U-Line S-15188 Bedienungsanleitung

ITATOOLS

ITATOOLS ITA22 Bedienungsanleitung

Fieldpiece

Fieldpiece MG44 Bedienungsanleitung

Smart wasp

Smart wasp X300 Bedienungsanleitung

U-Line

U-Line S-1135 Bedienungsanleitung

Z.R. Tools

Z.R. Tools MS25-1 Bedienungsanleitung

Sipromac

Sipromac SIPROVAC 620A Bedienungsanleitung

strapex

strapex STR 66 Bedienungsanleitung

U-Line

U-Line H-5334 Bedienungsanleitung

Imetec

Imetec Q5901 Bedienungsanleitung

Lacor

Lacor 69352 Technisches Datenblatt

Eastey

Eastey EXS-100 Bedienungsanleitung

Inova

Inova SV 125 Bedienungsanleitung

CombiSteel

CombiSteel 7529.0010 Bedienungsanleitung

HUALIAN

HUALIAN HVC-260T/1A Bedienungsanleitung

U-Line

U-Line H-2079 Bedienungsanleitung

Strapack

Strapack iQ400 Betriebsanleitung

FLOTER

FLOTER AirWave 2 Installationshandbuch