Traulsen R Series Bedienungsanleitung

-1-

Instructions for the installation,

use and care of:

R & A Series Roll-In

Refrigerators

R & A Series Roll-In

Hot Food Cabinets

Quality Refrigeration

Quick Start Guide

You should carefully inspect your Traulsen unit for damage during delivery. If damage is detected, you should save

all the crating materials and make note on the carrier’s Bill Of Lading describing this. A freight claim should be led

within 5 days.

Conrm that the correct power supply is available to the cabinet per the manufactures requirements as listed on

the cabinet data tag before cabinet installation. The area in which your cabinet is to be installed should be chosen

carefully to insure the best performance. The installation surface should be level and provide good area circulation.

After the cabinet is set in place, and leveled, an NSF approved sealant(Dow Corning Silastic RTX #732 for example)

should be used around the perimeter of the base to secure the unit to the oor and prevent the ingress of vermin and

water under the unit. After properly sealing the unit to the oor, the enclosed ramp should then be installed using the

instructions included in this guide.

Some models may use R-290 (Propane) as a refrigerant. If ammable refrigerant is present, follow instructions as

labeled on the unit. Proper care must be taken to avoid any damage to refrigeration system including refrigerant

tubing, condenser and evaporator coils during handling, moving, installation and cleaning as it may cause risk of re

or explosion. If damaged, unit must be moved to well ventilated area away from any sources of ignition.

Further service and repair must be performed by qualied refrigeration technicians familiar with applicable safety

standards for ammable refrigerants. Technicians must use appropriate personal protective equipment and follow

applicable safety pre cautions to avoid risk of re or explosion.

All models should be installed to allow at least 12” of clear space above the unit. In all cases the louvers must be free

of any obstruction which could prevent proper air-ow.

Most units are supplied with a cord and plug, which can simply be plugged into a dedicated appropriately sized outlet.

For those requiring hard-wiring directly to the power supply, this should be done by a qualied electrician only.

1. RECEIPT & SUPPORT INSTALLATION

TR36218 P/N 375-60366-00 (Rev. B 07/23)

-2-

2. RAMP INSTALLATION

2. a - STEP ONE

To install the ramp you will need to rst loosen and remove screws (351-60001-07) from both the left and right sides of the

breaker strip.

2. b - STEP TWO

Center the ramp to the door opening placing it 1-2 inches above the bottom of the unit. Move the ramp close to the unit (see

Figure A) until the ramp end is placed between screw heads and foam tape by visual inspection. Lower the ramp straight

down so that the screw heads capture the ramp end (see Figure B).

Figure A

RAMP END

FOAM TAPE

Figure B

-3-

2. RAMP INSTALLATION (continued)

2. c - STEP THREE

Install screws (351-60001-07) on the left and right sides but do not tighten (see Figure C).

Push the ramp into the unit until it is fully inserted, then tighten the screws on the left and right sides (see Figure D).

2. d - STEP FOUR

Loosen the four screws (351-60015-00) located on the door sweep but do not remove them.

Figure C

Figure D

351-60015-00

Qty: 4

DOOR SWEEP

-4-

2. e - STEP FIVE

Adjust the door sweep’s height to close the gap between the wiper’s bottom and the ramp’s surface, then tighten the screw

closest to the door hinge. Next, tighten the screw on the opposite end (closest to the door handle), then tighten the remaining

two screws in the middle.

2. RAMP INSTALLATION (continued)

3. ADJUSTMENTS

3. a - DOOR GASKET ADJUSTMENT

Door gaskets should be adjusted after the door sweeps have been adjusted and secured. Loosen the retaining screw holding

the door gasket in place normally located about six inches up from the bottom of the door in the interior fold of the gasket.

Raise the bottom gasket up until it is leveled with the bottom of the door sweep’s wiper. Secure the retaining screw. A new

hole may need to be made if the gasket is raised substantially.

3. b - DOOR/HINGE ADJUSTMENTS

All doors must be properly adjusted to insure they close properly. The door should close freely over the ramp. To remove the

door, you will need to remove the safety screw in the bottom of all hinges. The door should lift off the cabinet at this point.

There are three screws holding the hinge bracket to the cabinet. Loosen the three screws but do not remove them. You can

now adjust the hinge up or down and side to side. Tighten the three screws and replace the door and safety screws. Open

and close the door several times to make sure it closes freely.

-5-

3. c - LOCKKEEPER ADJUSTMENT

To adjust the lockkeeper, you will need to remove the two screws holding the lockkeeper. Loosen the two screws in the

bracket mounted on the cabinet but do not remove them. The bracket can be moved slightly from side to side. Tighten the

screws in the bracket and replace the lockkeeper. Make sure the lock bolt catches the lockkeeper so the door can be locked.

All Traulsen equipment is congured for optimum performance. However, you may make minor adjustments to your Traulsen

unit to suit your needs.

4. a - CONTROLLER DISPLAY

4. b - UNDERSTANDING THE DISPLAY

On the Upper Side of the display, there are colored LEDs for showing the temperature, status of the compressor, fans,

lock/unlock status, etc.

On the Lower Side of the display, there are ve capacitive touch buttons for managing the operation of the unit.

4. CONTROL BASICS

Unlock Symbol

Status Icons

ESC or Back Key

Unlock or Modify Key

Display or Enter Key

- or Previous Key

+ or Next Key

Cabinet Temp

DISPLAY

SYMBOL SYMBOL DESCRIPTION

Temperature Reading/Settings

Keypad Unlocked

Keypad Locked

Compressor On

Fan On

Defrost

Alarm/Door Open

DISPLAY

SYMBOL SYMBOL DESCRIPTION

Unlock/Modify Key

Minus (-)/Previous Key

Plus (+)/Next Key

Enter/Display Key

Esc/Back/Cancel Key

-6-

4. c - UNLOCKING THE KEYPAD

Normally, the keypad is locked to prevent inadvertent changes to settings. The Unlock Key is a white dot on the bottom of

the display, centered between the other four keys. Press the Unlock key twice within a second in order to unlock the keypad

(think “tap-tap”). The Keypad Unlocked LED will turn on to indicate the keypad is now live. The keypad will stay unlocked

until three minutes of inactivity have passed, at which time it will automatically lock the keypad. There are two operations

the user can perform without having to enter a password:

• Change the temperature setpoint • Initiate a defrost operation

4. d - CHANGING THE TEMPERATURE SETPOINT

The setpoint to the unit can be changed simply by pressing the Plus or Minus Key. There will be a slight delay at rst to

prevent an accidental change, so it will be necessary to hold the key for 3-4 seconds until the value starts to ash. The

ashing value indicates the setting is being modied. To raise the setpoint, press the Plus Key to increment to the setpoint

you want. Similarly, press the Minus Key to lower the setpoint. When the desired value is reached, press the Enter/Display

Key to lock in the value. Pressing the Esc Key will abort the process and keep the original setpoint. The keypad must be

unlocked in order to change the setpoint using the shortcut method.

4. e - INITIATING A DEFROST OPERATION

To manually defrost the unit, press the Minus Key and the Esc Key simultaneously and hold for 5 seconds. Units equipped

with an LED temperature display will indicate when a defrost cycle is in process. The Defrost Symbol will illuminate letting

you know defrost is in effect. Depending on the settings, the unit may also show “DEF”.

4. f - TURNING OFF HEATERS - HOT FOOD CABINETS ONLY

The keypad must be unlocked in order to de-activate the heaters. Press the Unlock key twice within a second in order to

unlock the keypad. The Keypad Unlocked LED will turn on to indicate the keypad is active. To turn the unit off, press and

hold the Unlock Key until the display shows “OFF”. To turn the unit ON, press the Unlock Key until the display shows the

temperature.

Disconnect electrical power supply before cleaning any parts of the unit. All Traulsen equipment should be cleaned only with

warm water, mild soap and a soft cloth. Apply with a dampened cloth and wipe in the direction of the metal grain.

Avoid the use of strong detergents and gritty, abrasive cleaners as they may tend to mar and scratch the surface. Do not use

cleaners containing chlorine as this may promote metal corrosion.

Care should also be taken to avoid splashing the unit with water containing chlorinated cleaners when mopping the oor around

the unit. For stubborn odor spills, use baking soda and water (mixed to a 1 TBSP baking soda to 1 pint water ratio).

5. GENERAL CARE

-7-

Disconnect electrical power supply before cleaning any parts of the unit. This is the single most important thing you

can do to promote long, efcient equipment life. For upright cabinets, remove the two bottom screws securing the louver

panel, then pivot this upwards allowing full access to the front facing condenser.

Vacuum or brush any dirt, lint or dust from the nned condenser coil, around the compressor and other cooling system parts

as indicated. If signicant dirt is clogging the condenser ns, use compressed air to blow this clear. When nished reverse

the louver removal process as instructed above.

6. CLEANING THE CONDENSER

SCREW LOCATION

-8-

7. TROUBLESHOOTING

Some models may use R-290 (Propane) as a refrigerant. Service and repair must be performed by qualied refrigeration

technicians familiar with applicable safety standards for ammable refrigerants. Technicians must use appropriate personal

protective equipment and follow applicable safely precautions to avoid risk of re or explosion. Service and repair must be

performed in well ventilated and unconned area, away from any ignition sources. All system components must be replaced

with like components. Factory recommends to use exact make and models to assure the consistent performance and to

minimize the risk of possible ignition due to incorrect parts. In case of uncertainty or parts unavailability, contact Traulsen

technical assistance at 800-825-8220.

PROBLEM POSSIBLE SOLUTION

Condensing unit fails to start. a. Check if cord & plug has been disconnected.

Condensing unit operates for prolonged periods or

continuously.

a. Are door(s) or drawer(s) closing properly?

b. Dirty condenser or lter. Clean properly.

c. Microprocessor control setting is too high, readjust.

Food Compartment is too warm. a. Check if a large quantity of very cold or frozen food

has recently been added. Allow adequate time for the

cabinet to recover its normal operating temperature.

b. Adjust the microprocessor control to a warmer setting,

readjust.

Food Compartment is too cold. a. Check if a large quantity of very cold or frozen food

has recently been added. Allow adequate time for the

cabinet to recover its normal operating temperature.

b. Adjust the microprocessor control to a warmer setting,

readjust.

Condensation on exterior surface. a. Check door(s) or drawer(s) alignment & gaskets for

proper seal.

b. Condensation on the exterior surface of the unit is

perfectly normal during periods of high humidity.

c. Check perimeter heat setting and increase setting if

<100.

-9-

8. SERVICE & WARRANTY INFORMATION

8. a - SERVICE SUPPORT

To speak to service support for Traulsen units please contact our Fort Worth, TX facility by phone at 800-825-8220 or by fax

to 817-740-6748 (parts) or 817-740-6757 (service).

Note: When calling for service support, please make sure you have model and serial number of unit available.

4401 Blue Mound Rd.

Ft. Worth, TX 76106

800-825-8220

Input Power (ELIN) -FOR INDOOR USE ONLY

115-208/230V ~ 60Hz 8.0A (8,0A)

MODEL:

MODELO:

MODELE: RDT232WUT-FHS

S/N: T25364A14

REFRIGERANT / REFRIGERANTE / RÉFRIGÉRANT

SYS1 (REFM): R-134a 8.4oz 238.1 g (238,1 g)

Hi Press. (PRESH): 500psi 3.45 MPa (3,45 Mpa)

Lo Press. (PRESL): 250 psi 1.72 Mpa (1,72 Mpa)

SYS2 (REFA): R-404a 12.5oz 354.4g (354,4g)

Hi Press. (PRESH): 500psi 3.45MPa (3,45MPa)

Lo Press. (PRESL): 250psi 1.72Mpa (1,72Mpa)

(Symbol 1)

(Alt Safety / Other

(Symbol 2)

(Alt. San / Other 2)

(Symbol 3)

(Alt. En. / Other 3)

(Symbol 4)

(WEEE)

(Symbol 5)

(Safety)

(Symbol 6)

(Sanitaon)

(Symbol 7)

(Energy)

(Symbol 8)

(Customer QR

Code / Other 4)

Device/Part Number: PartNum (UL/NSF Notes)

SCAN FOR SERVICE INFO

COMPONENTS / COMPOSANTS / COMPONENTES

COMP AMPS: EVAP FAN AMPS:

COND FAN AMPS: LIGHT WATTS:

DEF HTR AMPS: CTRL AMPS:

DOOR HTR AMPS: MIN AMPS:

MAX AMPS:

370-60297-00 REV.A 11/20/14

4401 Blue Mound Rd.

Ft. Worth, TX 76106

800-825-8220

Input Power (ELIN) -FOR INDOOR USE ONLY

115-208/230V ~ 60Hz 8.0A (8,0A)

MODEL:

MODELO:

MODELE: RDT232WUT-FHS

S/N: T25364A14

REFRIGERANT / REFRIGERANTE / RÉFRIGÉRANT

SYS1 (REFM): R-134a 8.4oz 238.1 g (238,1 g)

Hi Press. (PRESH): 500psi 3.45 MPa (3,45 Mpa)

Lo Press. (PRESL): 250 psi 1.72 Mpa (1,72 Mpa)

SYS2 (REFA): R-404a 12.5oz 354.4g (354,4g)

Hi Press. (PRESH): 500psi 3.45MPa (3,45MPa)

Lo Press. (PRESL): 250psi 1.72Mpa (1,72Mpa)

(Symbol 1)

(Alt Safety / Other

(Symbol 2)

(Alt. San / Other 2)

(Symbol 3)

(Alt. En. / Other 3)

(Symbol 4)

(WEEE)

(Symbol 5)

(Safety)

(Symbol 6)

(Sanitaon)

(Symbol 7)

(Energy)

(Symbol 8)

(Customer QR

Code / Other 4)

Device/Part Number: PartNum (UL/NSF Notes)

SCAN FOR SERVICE INFO

COMPONENTS / COMPOSANTS / COMPONENTES

COMP AMPS: EVAP FAN AMPS:

COND FAN AMPS: LIGHT WATTS:

DEF HTR AMPS: CTRL AMPS:

DOOR HTR AMPS: MIN AMPS:

MAX AMPS:

370-60297-00 REV.A 11/20/14

Please visit our website at www.traulsen.com for additional service, literature and parts information. From our home page

click on the SERVICE tab, and select one of the following:

SERVICE FINDER

OWNER’S MANUALS

PARTS PRICING

SERVICE & PARTS MANUALS

WARRANTY REGISTRATION

8. b - WARRANTY REGISTRATION:

The warranties for your new Traulsen unit may be registered with us by contacting our Fort Worth, TX facility directly by

phone at 800-825-8220.

Model Number

Serial Number

-10-

Quality Refrigeration

HOURS OF OPERATION:

Monday thru Friday 7:30 AM - 4:30 PM CST

Traulsen

4401 Blue Mound Road Fort Worth, TX 76106

Phone (800) 825-8220

Service Fax (817) 740 6757

www.traulsen.com

TR36218 P/N 375-60366-00 (Rev. B 07/23)

Andere Handbücher für R Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Traulsen Kühlschrank Handbücher

Traulsen

Traulsen UPT4812-LR Bedienungsanleitung

Traulsen

Traulsen TR35784 Bedienungsanleitung

Traulsen

Traulsen TU048QC Bedienungsanleitung

Traulsen

Traulsen RHT126WUT-FHS Bedienungsanleitung

Traulsen

Traulsen R Series Bedienungsanleitung

Traulsen

Traulsen TR35786 Bedienungsanleitung

Traulsen

Traulsen UHT27-R Bedienungsanleitung

Traulsen

Traulsen RHT132WPUT-FHG Bedienungsanleitung

Traulsen

Traulsen TR35787 Bedienungsanleitung

Traulsen

Traulsen RET232LUT Bedienungsanleitung

Traulsen

Traulsen RHT132EUT-FHS Bedienungsanleitung

Traulsen

Traulsen TR35755 Bedienungsanleitung

Traulsen

Traulsen RET232NUT-FHS, RET232NUT-HHS Bedienungsanleitung

Traulsen

Traulsen RRI264LPUT-FHS Bedienungsanleitung

Traulsen

Traulsen RHT132NUT-FHS Bedienungsanleitung

Traulsen

Traulsen ARI132HUT-FHS Bedienungsanleitung

Traulsen

Traulsen RDT132WPUT-HHS Bedienungsanleitung

Traulsen

Traulsen G10002P Bedienungsanleitung

Traulsen

Traulsen UC27HT Bedienungsanleitung

Traulsen

Traulsen ADT232NPUT-FHS Bedienungsanleitung

Traulsen

Traulsen TR35761 Bedienungsanleitung

Traulsen

Traulsen G10000 Bedienungsanleitung

Traulsen

Traulsen UHT Series Bedienungsanleitung

Traulsen

Traulsen TU044HT Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung