Treasure Cove Sand & Surf TC-1013 Bedienungsanleitung

Treasure Cove Metal Detector

Sand & Surf TC-1013

OWNER’S MANUAL

www.Treasure-Cove.com

805-288-5735

Manual revised 08-06-2013

Contents

Features .................................................................................................................................. 3

Treasure Hunter’s Code of Ethics ..................................................................................... 3

Preparation ............................................................................................................................. 4

Assembling the Detector ................................................................................................... 4

Installing Batteries ............................................................................................................. 4

Using Headphones ............................................................................................................ 5

Listening Safely ......................................................................................................... 5

Traffic Safety .............................................................................................................. 6

A Quick Look at Your Metal Detector ................................................................................... 6

Operation ................................................................................................................................ 7

Preparing the Detector ...................................................................................................... 7

Turning On the Detector ............................................................................................ 7

Tuning the Detector ................................................................................................... 7

Testing and Using the Detector ......................................................................................... 7

Indoor Testing ............................................................................................................ 7

Outdoor Testing and Use ........................................................................................... 8

Fine-Tuning the Detector .................................................................................................. 9

Adjusting Sensitivity ................................................................................................... 9

Adjusting Ground ....................................................................................................... 9

Adjusting Discrimination ............................................................................................. 9

False Signals ..................................................................................................................... 9

Detection Hints ................................................................................................................ 10

Pinpointing a Target ........................................................................................................ 10

Troubleshooting ................................................................................................................... 11

Care ....................................................................................................................................... 11

Features

With your 7& Metal Detector, you

can hunt for coins, relics, jewelry, gold, and

silver just about anywhere. The Metal Detec-

tor is versatile and easy to use. Its features

include:

Three-Tone Audio Discrimination —

sounds distinctive tones for different types of

metals, to make target identification easier.

Analog Meter— shows the probable type of

metal being detected.

Auto Tune — lets you tune your detector

quickly for accuracy.

Arm Support —lets you carry and operate

your detector comfortably.

Waterproof Search Coil — lets you use the

detector to search under water. (The search

coil is waterproof, but the detector’s control

housing is not waterproof.)

Adjustable Stem — lets you adjust the de-

tector’s length for comfortable use.

Headphone Jack — lets you connect head-

phones (not supplied) to the detector.

Low Battery Indicator — lets you know

when it is time to replace the batteries.

TREASURE HUNTER’S

CODE OF ETHICS

All treasure hunters might be judged by the

example you set. Here are a few basic rules

you should follow while using your detector.

• Always get permission before searching

any site.

• Respect the rights and property of oth-

ers.

• Observe all national, state, and local

laws while treasure hunting.

• Never destroy historical or archaeologi-

cal treasures. If you are not sure about

an object you have found, contact a

museum or historical society in your

area.

• Leave the land and vegetation as it was.

Fill in any holes you dig.

• Use your detector only in safe areas.

• Dispose of any junk you find, only in

approved areas. Do not leave it for the

next treasure hunter to find.

4Preparation

Preparation

ASSEMBLING THE

DETECTOR

Assembling your detector is easy and re-

quires no special tools. Just follow these

steps.

1. Turn the stem’s lock

nut clockwise until it

loosens.

2. Lengthen or shorten

the stem so when

you stand upright

with the detector in

your hand, the search

coil is level with and

about 1/2to 2 inches

above the ground

with your arm relaxed

at your side.

3. Turn the stem’s lock

nut counter-clockwise

to lock it in place.

4. Unscrew the knobs

on the search coil

and remove the

knobs and connec-

tor. Insert the stem

and align the holes

on the search coil

bracket and the stem.

Push the connector through the holes,

then replace and tighten the knobs.

5. Wind the search coil cable around the

stem. Leave enough slack in the cable

to let you adjust the search coil when

you are hunting on uneven ground.

6. Insert the search coil’s plug into the

search coil jack on the detector’s control

housing so the pins on the plug are

aligned with the holes in the jack.

Cautions:

• The search coil’s plug fits into the

connector only one way. Do not force

the plug or you could damage it.

• To disconnect the search coil’s cable

from the detector, grasp the plug and

pull it out of the connector. Never pull

on the cable.

7. Loosen the knob at the search coil’s

end, then adjust the search coil to the

desired angle. (The search coil should

be parallel with the ground.) Tighten the

knob just enough to keep the search coil

from rotating or wobbling.

Caution: Do not overtighten the search

coil or use tools such as pliers to tighten

it.

8. Loosen the knob at the base of the han-

dle, insert the arm support, and tighten

the knob.

INSTALLING BATTERIES

Your detector requires two 9V alkaline bat-

teries (not supplied) for power. For the best

performance and longest life, DOZD\VXVH

IUHVKalkaline batteries.

Cautions:

• Use only fresh batteries of the required

size and recommended type.

• Do not mix old and new batteries, differ-

ent types of batteries (standard, alka-

line, or rechargeable), or rechargeable

batteries of different capacities.

Lock Nut

Stem

Coil

Knobs

Arm

Support

Preparation

1. If the detector is on, turn MODE to OFF.

Note: When you turn the mode switch to

OFF, the LOW BATT indicator flashes

once.

2. Press the right battery compartment

cover’s tab and slide the cover off in the

direction of the arrow.

3. Place a 9-volt battery into the battery

compartment on top of the ribbon,

matching the polarity symbols (+ and –)

marked inside.

4. Replace the right battery compartment

cover.

5. Press the left battery compartment

cover’s tab and slide the cover off in the

direction of the arrow.

6. Place a 9-volt battery into the battery

compartment on top of the ribbon,

matching the polarity symbols (+ and –)

marked inside.

7. Replace the left battery compartment

cover.

Warning:

Dispose of old batteries promptly

and properly. Do not burn or bury them.

Caution: If you do not plan to use the detec-

tor for a week or more, remove the batteries.

Batteries can leak chemicals that can de-

stroy electronic parts.

Notes:

• For better life, exchange the two batter-

ies periodically.

• You can extend battery life by using

headphones, which require less power

than the built-in speaker. See “Using

Headphones.”

If the LOW BATT indicator lights during nor-

mal use or the detector does not function

properly, replace the batteries. If it still does

not function properly, you might need to re-

set the detector.

USING HEADPHONES

You can connect a pair of stereo head-

phones (not supplied) to the detector so you

can listen to it privately. Using headphones

also saves battery power and makes it easier

to identify subtle changes in the sounds you

hear, for better detection results. 

To connect head-

phones to the de-

tector, insert the

headphones’ 1/8-

inch plug into the

PHONE jack on the

side of the control

housing.

The detector’s in-

ternal speaker disconnects when you con-

nect headphones.

Listening Safely

To protect your hearing, follow these guide-

lines when you use headphones.

• Set the volume to the lowest setting

before you begin listening. After you

begin listening, adjust the volume to a

comfortable level.

PHONE

Jack

6A Quick Look at Your Metal Detector

• Do not listen at extremely high volume

levels. Extended high-volume listening

can lead to permanent hearing loss.

• Once you set the volume, do not

increase it. Over time, your ears adapt

to the volume level, so a volume level

that does not cause discomfort might

still damage your hearing.

Traffic Safety

Do not wear headphones while operating a

motor vehicle or riding a bicycle. This can

create a traffic hazard and could be illegal in

some areas.

Even though some headphones let you hear

some outside sounds when listening at nor-

mal volume levels, they still can present a

traffic hazard.

A Quick Look at Your Metal Detector

MODE — lets you select from

OFF, VLF, TR1, TR2. (See “Turn-

ing On the Detector” on Page 7.)

GROUND — compensates for

false signals from mineralized

soil. (See “Adjusting Ground”

on Page 9.)

VOLUME — lets you adjust the

volume of alert tones.

DISCRIMINATION — lets you ad-

just the metal detector’s ability

to distinguish between different

types of metal. (See “Adjusting

Discrimination” on Page 9.)

SENSITIVITY — lets you adjust

the detection depth. (See “Ad-

justing Sensitivity” on Page 9.)

TUNING — adjusts the balance

between the receiver and trans-

mitter. (See “Tuning the Detec-

tor” on Page 7.)

LOW BATT Indicator

Analog Meter

Operation

Your 7UHDVXUH&RYH Petal Getector distinguish-

es between ferrous and non-ferrous metals.

Ferrous metals contain iron, while non-

ferrous metals such as gold, silver, copper,

platinum, aluminum, lead, and zinc do not.

When the detector senses a metallic object,

the meter reading changes and the detector

sounds one of three tones. The tone de-

pends on what metal is detected. The higher

the tone’s pitch, the stronger the detection.

PREPARING THE

DETECTOR

Turning On the Detector

Hold the detector in a comfortable position,

then rotate MODE to the desired position.

VLF (Very Low Frequency) — to adjust TUNE

and GROUND. (See “Adjusting Ground” on

Page 9 and “Tuning the Detector” below.)

TR1 (Transmit 1) — to detect extreme differ-

ences in metals, such as iron and gold. The

difference between iron and gold shows on

the meter (iron in the ferrous section, gold in

the non-ferrous section).

TR2 (Transmit 2) — to detect finer distinctions

between metals, such as aluminum and gold

(see “Adjusting Discrimination” on Page 9).

Tuning the Detector

TUNE fine-tunes the balance between the de-

tector’s receiver and transmitter circuitry to

provide consistent pointer and tone indica-

tions. Follow these steps to set TUNE.

1. Rotate VOLUME to the 10 o’clock posi-

tion.

2. Set MODE to VLF.

3. Set GROUND, DISCRIMINATION, and

SENSITIVITY to mid-range.

4. Hold the search coil at least 1 foot away

from the ground and any metal object,

hold down the red button on the handle

and slowly rotate TUNE until the analog

meter pointer resets at or near 0.

As you search, you can fine-tune the detec-

tor using the other controls (see “Fine-Tuning

the Detector” on Page 9).

Note: Press the red button on the handle at

any time during operation to automatically re-

turn the pointer to the center of the analog

meter.

TESTING AND USING THE

DETECTOR

To learn how the detector reacts to different

metals, you should test it before you use it

the first time. You can test the detector in-

doors or outdoors.

Indoor Testing

1. Remove any watches, rings, or other

metal jewelry you are wearing, then

place the detector on a wooden or plas-

tic table.

2. Adjust the search coil’s angle so the flat

part faces the ceiling.

Note: Never test the detector on a floor

inside a building. Most buildings have

metal of some kind in the floor, which

might interfere with the objects you are

testing or mask the signal completely.

3. Set MODE to TR1.

4. Move a sample of the material you want

the detector to find (such as a gold ring

8Operation

or a coin) about 2 inches above the

search coil.

Notes:

• The search coil will not detect without

motion. You must move the object since

you are not sweeping with the detector

at this time.

• If you are using a coin, the detector

detects it more easily if you hold it so a

flat side (not the edge) is parallel with

the flat side of the search coil.

If the detector detects the material, the point-

er moves to FERROUS or NON-FERROUS

while the detector determines the type of

metal it is detecting. If it detects non-ferrous

metal, it also sounds a tone.

If the detector does not detect the material,

check the LOW BATT indicator and verify

that the search coil is properly connected. Al-

so, you might need to fine-tune the detector

See “Fine-Tuning the Detector” on Page 9

Outdoor Testing and Use

1. Find an area on the ground outside

where there is no metal.

2. Place a sample of material you want the

detector to find (such as a gold ring or a

coin) on the ground. (If you are using

valuable metal such as gold to test the

detector, mark the area where you place

the item, to help you find it later. Do not

place it in tall grass or weeds.)

3. Set MODE to TR1.

4. While holding the search coil level about

1–2 inches above the ground, slowly

move the search coil over the area

where you placed the sample, sweeping

the search coil in a side-to-side motion.

Search Coil Sweeping Hints:

• Never sweep the search coil as if it

were a pendulum. Raising the search

coil while sweeping or at the end of a

sweep causes false readings.

• Sweep slowly; hurrying makes you

miss targets.

If the detector detects the item, it sounds

a tone and the pointer moves to the type

of metal it found. When you detect

metal, switch MODE TR1 to TR2 to deter-

mine the quality of the metal.

If the detector does not detect the mate-

rial, make sure you are moving the

search coil correctly.

Notes:

• The detector responds with a strong

signal when it detects most valuable

metal objects. If a signal does not

repeat after you sweep the search

coil over the target a few times, the

target is probably junk metal.

• False signals can be caused by areas

containing large amounts of trash,

electrical interference, or large irregu-

lar pieces of junk metal. False signals

are usually broken or non-repeatable.

5. Try finding other metal in the area.

When you find a metal item, wait a few

seconds after the tone stops before con-

tinuing to allow the detector time to reset

(or, press the red button on the handle to

return the pointer to the center of the

analog meter).

Operation

FINE-TUNING THE

DETECTOR

After you become familiar with how your de-

tector works, you can fine-tune it to make it

less sensitive to interference and more se-

lective in what it finds.

Adjusting Sensitivity

To adjust the search coil’s ability to detect

objects at different depths in the soil, rotate

SENSITIVITY between MIN and MAX. For

maximum detection depth, leave SENSITIVI-

TY set as high as possible. If the detector

makes a “chattering” noise, decrease SENSI-

TIVITY until the chatter stops.

Adjusting Ground

Setting GROUND takes a little time, but is crit-

ical for accurate operation. GROUND tunes

out false signals from mineralized soil. Fol-

low these steps to set GROUND.

1. Set MODE to VLF and lower the search

coil to 1/2to 2 inches above the ground.

2. If the pointer swings to the right (Non-

ferrous), turn GROUND to NORMAL. If

the pointer swings to left (Ferrous), turn

GROUND to BASALT.

3. Raise the search coil about 1 foot from

the ground and press the red button on

the handle. The pointer returns to the

center.

4. Repeat Steps 1–3 until the pointer stays

close to the center each time you lower

the search coil to the ground.

After you set GROUND, the detector is set for

the soil type at that particular site. Do not re-

set it until you use the detector at a different

site.

Adjusting Discrimination

Discrimination is the detector’s ability to dif-

ferentiate between types of metal. The de-

tector’s DISCRIMINATION setting determines

whether the detector will distinguish between

different types of ferrous and non-ferrous

metals.

MODE is set to TR2, start with DISCRIMINA-

TION set to mid-range. While you use the de-

tector, adjust DISCRIMINATION to the best

position. As you set DISCRIMINATION higher,

the detector becomes more sensitive to the

differences between large aluminum and

gold pieces, for example, but some small

valuable pieces, such as coins and small

rings, might be overlooked.

As you set DISCRIMINATION to higher levels,

the detector first does not detect small piec-

es of silver paper, then thick foil, and finally

metal objects like pull tabs from aluminum

cans.

Note: Each time you use the detector in a

different area, you must readjust DISCRIMI-

NATION. Each search location presents new

challenges.

FALSE SIGNALS

Because your detector is extremely sensi-

tive, trash-induced signals and other sources

of interference might cause signals that

seem confusing. The key to handling these

types of signals is to dig for only those tar-

gets that emit a strong, repeatable signal. As

you sweep the search coil back and forth

over the ground, learn to recognize the differ-

ence between signals that occur at random

and signals are stable and repeatable.

To reduce false signals when searching ar-

eas containing large amounts of trash, scan

only a small area at a time using slow, short

overlapping sweeps.

10 Operation

DETECTION HINTS

No detector is 100 percent accurate. Various

conditions influence metal detection. The de-

tector’s reaction depends on a number of

factors:

• the angle at which the object rests in the

ground

• the depth of the object

• the amount of iron in the object

• the size of the object

PINPOINTING A TARGET

Accurately pinpointing a target makes dig-

ging it up easier. This takes practice, and we

suggest you practice finding and digging up

small metal objects on your own property be-

fore you search other locations.

Sometimes, targets are difficult to accurately

locate due to the sweep direction. Try chang-

ing your sweep direction to pinpoint a target.

1. When the detector locates a buried tar-

get, continue sweeping the search coil

over the target, in a narrowing side-to-

side motion.

2. Make a visual note of the exact spot on

the ground where the detector beeps.

3. Stop the search coil directly over this

spot on the ground. Then move the

search coil straight away from you and

straight back toward you a couple of

times.

4. Make a visual note of the exact spot on

the ground where the detector beeps.

5. Repeat Steps 1–3 at a right angle to the

original searchline, making an “X” pat-

tern. The target will be directly below the

“X” at the point of the loudest response.

Notes:

• If trash in an area is so heavy that you

get false signals, slow your sweep

speed and use shorter sweeps.

• Recently buried coins might not respond

the same as coins buried for a long

period of time because of oxidation.

• Some nails, nuts, bolts, and other iron

objects (such as old bottle caps) oxidize

and create a “halo” effect. A halo effect

is caused by a mixture of natural ele-

ments in the ground and the oxidation

created by different metals. Because of

the metal mixtures, target signals might

not be in a “fixed” position. This effect

makes these objects very hard to detect

accurately. (See “Fine-Tuning the Detec-

tor” on Page 9.)

Inhaltsverzeichnis

Andere Treasure Cove Metalldetektor Handbücher

Treasure Cove

Treasure Cove Vibra-Tector 720 Bedienungsanleitung

Treasure Cove

Treasure Cove TC3X Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Quatic 320 Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Quatic 2 Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 585 Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 570 Betriebsanleitung

Treasure Cove

Treasure Cove TC-3020 Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-iking 750 Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 570 Bedienungsanleitung

Treasure Cove

Treasure Cove Fortune Finder JUNIORTC-1010 Bedienungsanleitung

Treasure Cove

Treasure Cove TC2X Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 585 Bedienungsanleitung

Treasure Cove

Treasure Cove E-Z Swing Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 560 Bedienungsanleitung

Treasure Cove

Treasure Cove Hobbyist TC-1006 Bedienungsanleitung

Treasure Cove

Treasure Cove Fast Action TC-1018 Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Quatic 2 Bedienungsanleitung

Treasure Cove

Treasure Cove Fortune Finder 1020 Bedienungsanleitung

Treasure Cove

Treasure Cove TC1X Bedienungsanleitung

Treasure Cove

Treasure Cove Professional 9700 Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Tector 740 Bedienungsanleitung

Beliebte Metalldetektor Handbücher anderer Marken

Garrett

Garrett MAGNASCANNER CS 5000 Bedienungsanleitung

Valex

Valex 1800200 Bedienungsanleitung

Gauss

Gauss MIL MD Bedienungsanleitung

Velleman

Velleman CS130 Bedienungsanleitung

Sears

Sears 321.596370 Bedienungsanleitung

Eriez

Eriez X8 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-22 Bedienungsanleitung

Zircon

Zircon MetalliScanner m60c Bedienungsanleitung

nalanda

nalanda MD027 Bedienungsanleitung

REV Ritter

REV Ritter CB-7005 Bedienungsanleitung

Minelab

Minelab F1A4 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs F70 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-12 Bedienungsanleitung

GOLDEN MASK

GOLDEN MASK 5 Bedienungsanleitung

Grizzly

Grizzly YM 203 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Bedienungsanleitung

Accurate Locators

Accurate Locators XL16 IMAGER Bedienungsanleitung

Teknetics

Teknetics G2 Bedienungsanleitung