T50
-2-
SAFETY
WARNING:
Observe the safety regulations in the
instruction manual of the power tool to
be used. Please read the following
instructions carefully. Failure to do so
could lead to serious injury. When using
electric tools, basic safety precautions,
including the following should always be
followed to reduce the risk of fire,
electric shock and personal injury. Also
observe any applicable additional safety
rules. Read the following safety
instructions before attempting to operate
this product.
PLEASE KEEP THESE
INSTRUCTIONS IN A SAFE PLACE.
The attention of UK users is drawn to
The Provision and Use of Work
Equipment Regulations 1998, and any
subsequent amendments.
Users should also read the HSE/HSC
Safe Use of Woodworking Machinery
Approved Code of Practice and
Guidance Document and any
amendments.
Users must be competent with
woodworking equipment before using
our products.
IMPORTANT NOTE:
Residual Risk. Although the safety
instructions and operating manuals for
our tools contain extensive instructions
on safe working with power tools, every
power tool involves a certain residual
risk which cannot be completely
excluded by safety mechanisms. Power
tools must therefore always be operated
with caution!
General
1. Disconnect power tool and
attachment from power supply when
not in use, before servicing, when
making adjustments and when
changing accessories such as
cutters. Ensure switch is in “off”
position. Always ensure cutter has
stopped rotating.
2. Always mount the power tool,
accessory or attachment in
conformity with the instructions. Only
use attachment and accessories
specified in the power tool manual.
The tool or attachment should not be
modified or used for any application
other than that for which it was
designed. Do not force tool.
3. Keep children and visitors away. Do
not let children or visitors touch the
tool, accessory or attachment. Keep
children and visitors away from work
area. Make the workshop child proof
with padlock and master switch.
4. Dress properly. Do not wear loose
clothing or jewellry, they can be
caught in moving parts. Rubber
gloves and non-skid footwear is
recommended when working
outdoors. Wear protective hair
covering to contain long hair.
5. Consider working environment. Do
not use the product in the rain or in
a damp environment. Keep work
area well lit. Do not use power
tools near gasoline or flammable
liquids. Keep workshop at a
comfortable temperature so your
hands are not cold. Connect
machines that are used in the
open via a residual current device
(RCD) with an actuation current of
30 mA maximum. Use only
extension cables that are approved
for outdoor use.
6. The accessory or attachment must
be kept level and stable at all
times.
7. Keep work area clean. Cluttered
workshops and benches can cause
injuries. Ensure there is sufficient
room to work safely.
8. Secure idle tools. When not in
use, tools should be stored in a dry
and high or locked up place, out of
reach of children.
9. For best control and safety use
both hands on the power tool and
attachment. Keep both hands
away from cutting area. Always
wait for the spindle and cutter to
stop rotating before making any
adjustments.
10. Maintain tools and cutters with
care. Keep drill bits sharp and
clean for better and safer
performance. Do not use
damaged drill bits. Follow
instructions for lubricating and
changing accessories. Keep
handles dry, clean and free from oil
and grease.
11. Maintain accessories. Do not use
damaged accessories. Only use
accessories recommended by the
manufacturer.
12. Check damaged parts. Before
operation inspect the attachment,
the power tool, the cable,
extension cable and the plug
carefully for signs of damage.
Check for alignment of moving
parts, binding, breakage, mounting
and any other conditions that may
effect its operation. Have any
damage repaired by an Authorised
Service Agent before using the tool
or accessory. Protect tools from
impact and shock.
13. Do not use tool if switch does not
turn it on or off. Have defective
switches replaced by an Authorised
Service Agent
14. Do not over reach. Keep proper
footing and balance at all times. Do
not use awkward or uncomfortable
hand positions.
15. Don’t abuse the cable. Never carry
power tool or accessory by cord or
pull it to disconnect from the socket.
Keep cord from heat, oil and sharp
edges. Always trail the power cord
away from the work area.
16. Check all fixing and fastening nuts,
bolts and screws on power tool,
attachment and drilling tools before
use to ensure they are tight and
secure. Periodically check when
machining over long periods.
17. Stay alert. Watch what you are
doing. Use common sense. Do not
operate tools when you are tired,
under the influence of drugs or
alcohol.
18. Personal Protective Equipment
(PPE) for eye, ear and respiratory
protection must be worn. All PPE
must meet current UK and EU
legislation.
19. Do not leave tools running
unattended. Do not leave tool until
it comes to a complete stop.
20. Always clamp workpiece being
machined securely.
21. Vibration levels. Hand held power
tools produce different vibration
levels. You should always refer to
the specifications and relevant
Health & Safety Guide.
Version 7.1 06/2006 PT2
MANU-T50 v1.0 6/11/06 2:14 pm Page 2
