Trevi 228 Bedienungsanleitung
When selecting a site for your pool, take into account city by-
laws regarding fences and utilities laws pertaining to electrical
cables, as well as the landscaping which you are planning once
the pool is installed.
Drive a stake into the ground at the center of the site. Using a meas-
uring tape, draw a circle 15 cm to 20 cm (6" to 8") longer in radius
than the pool, depending on the width of the uprights (See Illustra-
tion 1.1).
Remove all grass from the area which you have just outlined.
Make sure to order the required quantity of sand and stone dust
(See Chart).
Dear Customer
Congratulations! You have purchased a pool of superior quality and durability. To achieve the best possible results,
follow the instructions carefully. Failure to follow the installation procedures may result in damage to your pool or
property and void your warranty. We recommend that you make a preliminary study of the instruction booklet to
familiarize yourself with the different parts of your pool. Make sure that you understand each step thoroughly before
you begin assembling.
We wish you a most pleasant and refreshing summer.
WARNING: Be sure you have read and understand the “Safety Information” sheets
before you begin your pool installation.
WARNING: For your safety, your pool is not designed for diving and/or jumping head first.
Please do not dive. Diving may result in permanent injury or death.
ASSEMBLY INSTRUCTIONS
ROUND POOL
MODEL 228-230-248
SITE PREPARATION
1
WALL
DIAMETER
TURF
REMOVAL DIAMETER
Diameter
Illustration 1.1
40302_V2_2021-01-23
SITE PREPARATION (continued)
1
SITE LEVELLING
2
Level the edge of the circle, from the turf removal line up to 30 cm
(12”) within the circle.
To do this, use a carpenter’s level set on a large straight beam, a
rope or an optical level.
Carefully pack the soil using a tampering tool or vibrating plate (See
Illustrations 2.1 and 2.2), especially those areas where a large
quantity of soil was added.
It is also highly recommended to firm up the edge by adding a 2
cm (3/4”) layer of stone dust (or sand).
Optional
The center of the circle can then be excavated at the desired depth,
not to exceed 15 cm (6”) for a standard liner (See Illustration 2.3).
Remove any stone, pieces of wood or other debris from within the
circle. Flatten any protrusion and pack the soil tightly. Spread the
area with salt to prevent roots from growing back and to eliminate
earthworms. Spread also ant repellant; all causes of post-installa-
tion cracking.
To protect the liner, cover with a think 2 cm (3/4") layer of com-
pacting sand.
Make sure you add a sufficient quantity of sand to the base finishing
inside the circle (See Step 6).
9,14 m (30’) 4.57 m (15’ 8") 2 1/2 Tons 2 Tons9.14 m (31’ 4")
3,05 m (10’) 1,72 m (5’8”) 3,05 m (11’6”)
* If you use only sand, add stone dust tonnage to sand.
Chart
TURF
REMOVAL
DIAMETER
30 cm
(12")
WALL
DIAMETER
10’- 0" DIAM. Plat : 2’ - 0"
12’- 0" DIAM. Plat : 2’ - 0"
15’- 0" DIAM. Plat : 2’ - 0"
18’- 0" DIAM. Plat : 2’ - 6"
21’- 0" DIAM. Plat : 2’ - 9"
24’- 0" DIAM. Plat : 3’ - 0"
27’- 0" DIAM. Plat : 3’ - 0"
30’- 0" DIAM. Plat : 3’ - 0"
Illustration 2.3
Dig a hole 30 cm (12") wide by approximately 25 cm (10") deep in
the center of the circumference.
From the center hole to the projected location of the pool motor, dig
a 15 cm (6") wide trench. Place the removed soil aside to be used
later to cover the hose.
Bottom Drain Assembly
Place teflon around the threaded plug. Screw in drain holes using
large pliers. Glue the connector in the appropriate opening.
Take one of the two rubber rings and adjust it to the top of the drain,
aligning the holes carefully. Secure with strips of adhesive tape to
prevent sand from penetrating inside the holes once the drain has
been installed.
Secure one end of the long black or white hose inside the drain
spout. First apply glue on the drain spout and inside the drain end,
then secure with one or two collars.
Cut the hose so that it ends with the stone dust (or sand). Measure
the pool radius from the center of the drain, then add 15 cm (6").
Place the assembled bottom drain in the hole so that it is approxi-
mately 1.3cm (1/2") higher than the surface soil. Bury the hose,
levelling the drain as much as possible. Compact the soil, using
your feet and a tampering tool as well.
Mix three (3) shovels of stone or sand dust with one half shovel of
pure cement, adding a small quantity of water, then pour the cement
around the drain until it reaches 1.3 cm (1/2") from the top.
BOTTOM DRAIN ASSEMBLY (if applicable)
3
Insert the wall tracks on each side of the joiner plates. Evenly space
the ends of both tracks in the center of the joiner plate. (See Illus-
tration 4.1).
Make a complete circle, using half of the wall tracks and joiner
plates found in the pool kit (See Chart and Illustration 4.2).
BOTTOM WALL TRACKS ASSEMBLY
4
Illustration 4.1 Illustration 4.2
9,14 m (30’) 21 21
3,05 m (10’) 10 10
Add sand.
Before uncoiling the wall, make sure the pre-punched holes for the
skimmer and pump return are at the top and facing the planned lo-
cation of your filter.
Begin inserting the wall into the bottom wall tracks in the middle of
a joiner plate. At first, the wall is kept in place with one or two stakes
and strings (or extra persons). One person uncoils the wall on a
beam or a plank, while a second person inserts it in the bottom wall
tracks. Do not uncoil more than 3 m (10') of wall before you install
a support bar or stake and string to reinforce the structure.
Once the wall is completely uncoiled, you may find that it is too long
or that both ends do not meet by a few centimetres. If such is the
case, adjust tracks and joiner plates until wall holes line up. If this
does not work, roll up the wall again, check measurements as per
Illustrition 1.1, adjust tracks and plates, if applicable, and uncoil the
wall again. If the spread is too wide, measure the wall and check it
against the chart below.
Join the ends of the walls by orienting folds outward to hide the ex-
clamation icon. (Illustration 8.1)
Note: If the wall is attached properly, you should no longer see
the exclamation icon. If you can always see the icon, you must
reverse the overlap.
Insert bolts and nuts in every hole and tighten with wrench (screw
head on water side of wall). Tape over screw heads with duck tape.
WALL INSTALLATION
5
SAND
STAKE AND STRING
PLANKS
End
BOTTOM PLATE
Illustration 5.1
Donot use impactgunfor wall
screws.
Minimumtorqueforceof 60inch
poundsto maximumof 85 inch pounds.
Outsideof pool
Insideof pool
Fold
Fold
BOLT End
Start
NUT
Insideof pool
Outsideof pool
!
IMPORTANT! Installing the wall joint in non-compliance with the specifications dictated by the manufacturer will void the warranty.
A
faulty installation will cause the wall/joint to split which could result in serious and/or fatal injuries!
You can now spread approximately 10 cm (4") of compacting sand
all around the inside base of the wall in order to protect the liner
from the cutting edges of the bottom wall tracks and the stone dust
(if applicable), or install a prefabricated cove if available.
SAND BASE FINISHING
Level finishing sand one last time. Make sure that any sharp stones,
debris or roots have been removed from the surface. For better pro-
tection, spray sand with water and pack it once more until the base
is nicely even.
SAND BASE FINISHING
6
WALL INSTALLATION (continued)
5
Before pulling the liner up against the wall, insert a va-cuum cleaner
hose down into the pump return hole to approximately 15 cm (6")
from the ground.
Maintain the hose in place with adhesive tape. Don't forget to block
the skimmer hole with adhesive tape to prevent air from leaking in.
Place the unfolded liner in the center of the pool area at right angles
with the skimmer hole. Make sure you wear light, flat-soled shoes
to walk on the sand as the slightest heel mark could be visible once
the pool is filled.
Carefully unfold the liner, bringing the bottom-sidewall seam close
to the wall base. Make sure that the side with the protruding seams
faces downward or that the patterned side faces upward.
VINYL LINER INSTALLATION
7
Chart
9,14 m (30’) 28,72 m (94’ 3")
3,05 m (10’) 9,60 m (31’ 6")
LINER
WALL
30 cm (12")
10 cm (4")
SAND COVE
(or PREFAB COVE) BOTTOM
TRACK
PUMP RETURN HOLE
VACUUM CLEANER
INNER WALL
GROUND LEVEL
15 cm (6")
VINYL LINER INSTALLATION (continued)
7
Lift up a section of the liner over the top of the wall leaving a 10 cm
to 15 cm (4" to 6") fringe outside the wall. Secure the liner with a
plastic coupler (sold separately). Install the top track on the wall
then install the top plates on top of each upright.
At this point, the liner may be too tight, making it difficult to drape
the overlap or, on the contrary, too loose. In such cases, you will
have to redistribute the tension in the liner by removing some of the
couplers and readjusting the liner.
Installation detail of a bead liner with top track.
Hang the liner on the top of the wall and install the top track to se-
cure.
Start the vacuum cleaner to allow the liner to adhere to the wall and
check for excess tension at the bottom or for wrinkles. Adjust the
liner by removing wrinkles if needed, lift or lower it in order to ensure
a perfect fit.
Fill the pool with water up to the base of the wall before stopping
and removing the vacuum cleaner.
PUMP RETURN FITTING
After you remove the vacuum cleaner, you may install the return fit-
ting. Place the return fitting ring against the liner and adjust it so
that it is perfectly aligned with the hole in the wall. When the ring is
properly positioned and secured, cut the liner in the middle of the
ring.
Insert the return fitting from the inside, placing the first gasket be-
tween the return fitting and the liner and the second between the
wall and the liner. Then tighten the outside ring with large pliers, tak-
ing care not to crease the liner.
BOTTOM DRAIN (optional)
Find the holes through the middle of the liner and screw the ring
and gasket in against the liner before cutting the liner in the middle
of the ring, then screw on the drain cover.
UPRIGHT POST TOP PLATE INSTALLATION
8
OVERLAP
LINER
RESIN TOP
TRACK
WALL
PLASTIC
COUPLER
(SOLDSEPARATELY)
U-BEAD
LINER
RESIN TOP
TRACK
WALL
STEEL
TOP TRACK
PLASTIC
COUPLER
(SOLDSEPARATELY)
STEEL
TOP TRACK
Slide the top plate on the upper side of the upright, and secure with
one (1) screw “Z”.
SCREW ‘’Z‘’
228 230
228 230
UPRIGHT POST INSTALLATION
9
TOP SEAT INSTALLATION
10
Attach the uprights to the bottom plate with two (2) screws “Z”,
which you will find in the hardware bag.
Uprights must be installed outside the flanged part of the bottom
plate and into the two notchs of the bottom track.
Be sure to have a vertical (plumb) upright before fixing the top seat.
Place the top seat on the upper side of the upright.
Center the top seat between the two uprights and secure with four
(4) screws “Z”.
SCREW ‘’Z‘’
‘’Z’’SCREW
BOTTOM
PLATE
SEAT CAP INSTALLATION
11
SECURITY LABELS INSTALLATION
12
Install the four (4) safety labels (DANGER) supplied with your pool
as follows: two (2) labels visible at the entrance to the pool and two
(2) visible at the main access of the backyard.
Important: if you require additional labels, please contact us at
Trevipools.com
Install a minimum of three (3) safety labels (supplied with the liner)
inside the pool so that at least one label is visible no matter where
the bather enters the water (see drawing for positionning)
LABEL
Put the seat cap on the inside section of the seat and interlock with
the upright. Secure the seat cap with one (1) screw “Z”.
Snap the cap logo on top of the upright and secure the bottom with
one (1) screw ‘’Z’’.
FILTRATION SYSTEM ASSEMBLY
13
PARTS LIST
14
CAP LOGO#
Z
TOP PLATE
BOTTOM PLATE
BOTTOM TRACK
TOP TRACK
POOL WALL (Finish lenght, inch)
UPRIGHT 52’’
TOP SEAT
SCREW no 1/4 x 1 po
BOLT &NUT FOR 52’’ WALL
SEAT CAP
POOL LINER
PLASTICCOUPLER
Z
Z
Z
Z
N
Assemble skimmer, inlet, drain, filter, pumps, hoses according to separate
manufacturer’s instructions.
Note: See 'Safety Information" Manual.
SAFETY AND FUN GO
TOGETHER!
SAFETY INFORMATION
Read this before installing your above-ground pool.
12 775, Brault Street, Mirabel, Quebec, Canada J7J 0C4
Phone: 1 800 44-TREVI (1 800 448-7384)
Fax: 1 866 777-0167
Andere Handbücher für 228
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Sprachen:
Andere Trevi Schwimmbad Handbücher
Trevi
Trevi 128 Bedienungsanleitung
Trevi
Trevi 206 Bedienungsanleitung
Trevi
Trevi 222 Bedienungsanleitung
Trevi
Trevi 106-206-118-218 Bedienungsanleitung
Trevi
Trevi 211 Bedienungsanleitung
Trevi
Trevi 228 Bedienungsanleitung
Trevi
Trevi 128 Bedienungsanleitung
Trevi
Trevi 230 Bedienungsanleitung
Trevi
Trevi 228 Bedienungsanleitung
Trevi
Trevi 205 Bedienungsanleitung
Trevi
Trevi 106 Bedienungsanleitung
Trevi
Trevi 222 Betriebsanleitung
Trevi
Trevi 178 Bedienungsanleitung
Trevi
Trevi 130 Bedienungsanleitung
Trevi
Trevi 211 Bedienungsanleitung
Trevi
Trevi 130-178-179-180 Bedienungsanleitung
Trevi
Trevi 211 Bedienungsanleitung
Trevi
Trevi 128 Bedienungsanleitung
Trevi
Trevi 213 Bedienungsanleitung
Trevi
Trevi 106-206-186 Bedienungsanleitung
