Triarchy Technologies VSG6G1 Bedienungsanleitung

Page 1 of 33

Triarchy®VSG6G1/VSG2G1/TSG4G1

USB Vector RF Signal Generator

Operating Manual

CW signal Analog modulation GMSK modulation 64 QAM NB RF noise generator

Pulse modulation Frequency sweeping Hopping with data Mod GSM signal arbitrary signal generator

Page 2 of 33

USB Vector RF Spectrum Analyzer Operating Manual

Initial Version August 2015

Documentation version 1.0

No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into

any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,

manual, or otherwise, without the prior written permission of Triarchy Technologies, Corp.

Technical Support

For technical support, please call 1-604-637-2167, send email to info@triachytech.com, or visit our website at

http://www.triarchytech.com

Page 3 of 33

Contents

1 Introduction 4

1.1 Product Package Overview 4

1.2 USB Device Overview 4

1.3 TSG PC Application Overview 5

1.4 Electrical Requirements 7

2 Getting Started 9

2.1 Install PC Application 9

2.2 Uninstall PC Application 11

2.3 First Working Example 11

2.4 TSG Utility keys setting 11

3 Operations 13

3.1 CW Signal Output 13

3.2 Pulse modulation Signal Output 14

3.3 AM Signal Output 14

3.4 FM Signal Output 15

3.5 Frequency shift 16

3.6 Analog Modulation with I&Q raw data file 16

3.7 GMSK signal Output 17

3.8 FSK signal Output 18

3.9 Digital Modulation with I&Q Engine 18

3.10 QPSK Signal output 19

3.11 8PSK Signal output 20

3.12 16QAM Signal output 20

3.13 Phase Modulation with I&Q Engine 21

3.14 Frequency Sweeping without Pulse Modulation 22

3.15 Frequency Sweeping with Pulse Modulation 23

3.16 Frequency hopping without Pulse Modulation 23

3.17 Frequency Hopping with Pulse Modulation 24

3.18 S11/S21 measurement 25

3.19 Example for GSM signal output 26

3.20 Pulse modulation signal output 27

3.21 SIN/Triangle/Spiral waveform signal output 27

3.22 Clock selection 27

3.23 I&Q Selection 28

3.24 Hardcopy Operation 28

4 I&Q Engine 28

4.1 I&Q Engine principle 28

4.2 I&Q file configuration 31

Page 4 of 33

1 Introduction

VSG6G1/VSG2G1/TSG4G1 is a USB RF signal generator that plugs on PC and works using PC or tablet application.

For VSG6G1: the RF frequency range is from 1MHz to 6.2GHz, amplitude output range will be -60dBm~10dBm.

For VSG2G1: the RF frequency range is from 30MHz to 2.2GHz, amplitude output range will be -60dBm~10dBm.

For TSG4G1: frequency range is from 35MHz to 4.4GHz, and amplitude is from -60dBm to 0dBm.

VSG6G1 /VSG2G1/TSG4G1 will be very easy to use. The application's user interface is designed to be just like

the front panel of normal desktop signal generators, allowing signal generator users to easily pick up and use the

application intuitively without a high learning curve. If your PC or tablet support touch screen, the user

experience will be even more realistic to a desktop signal generator.

VSG6G1 have additional functions: such as the generation of modulation signal with I&Q engine and Pulse

modulation so that it can simulate a lot of wireless systems.

1.1 Product Package Overview

VSG6G1/VSG2G1/TSG4G1 product package will be:

1: USB signal generator device (25x25x100mm) one piece

2: mini USB cable one piece

3: SMA to MMCX cable one piece

4: N to SMA adapter one piece

5: 30 dB attenuator one piece

6: CD with PC application program and document one piece

7: 160x110x40mm product case one piece

1.2 USB Device Overview

RF output

N connector (female)

RF signal output

USB connector

Mini-B USB connector

interface with PC

MMCX connector

I port positive Output/Input

MMCX connector

I port negative Output/Input

MMCX connector

Q port positive Output/Input

MMCX connector

Q port negative Output/Input

Clock

MMCX connector

Clock Output/Input

Pulse

MMCX connector

Pulse signal Output

Page 5 of 33

1.3 TSG PC Application Overview

1: utility keys

Allows user to access the system level function. Function detail will be shown on second function keys

2: Message selection keys

Click the Message selection key, the Message display area will change according to selection.

3: Message display area

Message display area shows detailed information about output signal.

Main Block Diagram illustrates how the RF vector signal generator working, how the signal is output.

Freq Hopping setting shows a table of hopping frequency points.

I&Q Streaming Raw Data is waveform of I&Q raw data, it will be same as real waveform signal from I&Q

port.

I&Q pattern image shows I&Q pattern if I&Q raw data is generated based on the I&Q pattern.

I&Q constellation diagram is shown, it will be selected depending on Raw data or I&Q pattern.

S11, S21 Measurement shows the waveform of S11 and S21 test result.

4: Status block

Status block shows the main parameter of output signal: such as frequency, amplitude, repeat time,

duration, symbol rate and working mode.

Page 6 of 33

5: Second functions keys

Second function keys will extend secondary functions relative to the primary function keys and utility

key. It is similar to soft key in most of equipment which is location on side of screen.

6: Function keys

Most of major the equipment settings are done by the Function keys. General setting for signal

generator will be: Select mode: such as frequency selection for single, sweeping and hopping and pulse

modulation selection.

Input frequency: such as setting for signal frequency, frequency sweeping and frequency hopping

Input amplitude: such as level setting, external attenuator selection and setting.

Input timing: for pulse modulation.

Adding I&Q modulation: to setup a lot of different kind of modulation to meet each application

requirements.

7: Digital input keys

Digital input keys will input digital and units for frequency, amplitude and timing. This standalone input

key is similar to desktop equipment

Frist select the digital at second function, frequency, amplitude and timing.

Then operate keypad , navigation keys and Knob to change the input value.

Knob Operation

When the mouser cursor hovers over each of the four buttons on the knob: ++, +, --, - icon will display.

Click and hold on each icon to increase or decrease value:

++ fast increase

+ slowly increase

-- fast decrease

- Slowly decrease

After input digital, it need to input unit to finish all setting.

8: USB connection area

When VSG6G1/VSG2G2/TSG4G1 is plugged in the PC, USB connection area will display the product

model name, S/N and connection status. A device is properly connected to and recognized by the

application program when Model number, S/N and connected status are all displayed.

Page 7 of 33

9248 163 Street

Surrey, BC V4N 3C9

604-637-2167

info@triarchytech.com

One PC can connect multiple VSG6G1/VSG2G1/TSG4G1 device. Select S/N item to choose which device

will is used. When multiple TSG application are opened, each TSG can connected to each hardware

device by choice proper the S/N.

1.4 Electrical Requirements

1.41 Specification for Frequency

Frequency range for VSG6G1:

Band 0: 1MHz ~30MHz Band

1: 30MHz ~2200MHz Band 2:

2200MHz ~6200MHz

Frequency range for VSG2G1:

Band 1: 30MHz ~2200MHz

Frequency range for TSG4G1:

Band 1: 35MHz ~4400MHz

Frequency resolution: 1 KHz with PLL setting

Frequency offset: +/-2Hz to +/-1KHz with I&Q Freq Shift +/- setting

* frequency offset can only be setup at single frequency mode without any modulation ( not working at TSG4G1)

Frequency stability: +/-2.5PPM over temperature -20~+60 degree

Frequency aging per year: +/-1PPM

Frequency reference output: 12MHz

Frequency reference input: 10MHz/5dBm

1.4.2 Specification for power

Output level range for VSG6G1 :

Band 0: -21dBm~10dBm

Band 1: -21dBm~10dBm

Band 2: -31dBm~0dBm

Output level range for VSG2G1 :

Band 1: -21dBm~10dBm

Output level range for TSG4G1 :

Band 1: -31dBm~0dBm

Output level resolution: 1dB

Output level error: <3dB

Phase noise:

-90dBc/Hz offset 10 KHz at 1GHz

-105dBc/Hz offset 100 KHz at 1GHz

-120dBc/Hz offset 1MHz at 1GHz

Page 8 of 33

9248 163 Street

Surrey, BC V4N 3C9

604-637-2167

info@triarchytech.com

1.4.3 Specification for Pulse modulation

Pulse repeat time: 400uS to 20s

Pulse duration time: 10us to 5S

Multiple pulse number: 2~250

Multiple pulse delay: 100us~5s (last pulse cannot be overlay with first pulse)

On/off ratio: >90dB

1.4.4 Specification for Frequency sweeping with/ without pulse modulation

Span range: 1 KHz to full span

Scan points range: 2 to 50000

Frequency step range: 1 KHz to 1GHz

Pulse period ( set at Pulse Mod): repeat time 400uS to 20s

Pulse width ( set at Pulse Mod): duration time 10us to 10s

* If it is in “Freq sweeping w/o Pulse mod”, this parameter is no function

1.4.5 Specification for Frequency hopping with/ without pulse modulation

Frequency hopping range: 1MHz to 6.2GHz (30MHz to 2.2GHz for VSG2G1/

35MHz to 4.4GHz for TSG4G1)

Frequency hopping number: 2~4000

hopping times(Pulse period): 2500 hop/s to 0.05 hop/s (or repeat time 400uS to 20s)

Pulse width ( set at Pulse Mod): duration time 10us to 10s

* If it is in “Freq hopping w/o pulse mod”, this parameter is no function

1.4.6 Specification for I&Q unit for analog modulation (not suit for TSG4G1)

FM modulation in Demo key: Modulation frequency range: 1.5Hz to 3.3KHz; Modulation index 20

FM modulation by defined the file, load different file:

Modulation frequency range: 1.5Hz to 33KHz

Modulation index 0.5 to 20

AM modulation in Demo key: Modulation frequency range: 30.7Hz to 66.7KHz; Modulation index 90%

AM modulation by defined the file, load different file:

Modulation frequency range: 1.5Hz to 66.7KHz

Modulation index 10%to90%

PM modulation in Demo key: Modulation frequency range: 30.7Hz to 66.7 KHz;

Modulation index 180 degrees

PM modulation by defined the file, load different file:

Modulation frequency range: 30.7Hz to 66.7KHz

Modulation index 36 degree to 288 degree

*Define the I&Q RAW data file, any kind of analog modulation can be achieved. Such as RF narrow band noise

generator.

1.4.7 Specification for I&Q unit for Digital modulation (not suit for TSG4G1)

MSK modulation in Demo key: Data rate rage: 110b/s to 240Kb/s; Data depth: 400 bit

GMSK modulation in Demo key: Data rate rage: 110b/s to 240Kb/s; Data depth: 400 bit; BT=0.3

FSK modulation in Demo key: Data rate rage: 27.7b/s to 60Kb/s; Data depth: 25 bit

* Define the I&Q data file, study different I&Q pattern, internal I&Q engine will generate the most of digital

modulation; Such as SFSK.

1.4.8 Specification for I&Q unit for phase modulation (not suit for TSG4G1)

QPSK modulation in Demo key: Data rate rage: 2.2kb/s to 4.8Mb/s; Data depth: 4000 bit

8PSK modulation in Demo key: Data rate rage: 3.3kb/s to 7.2Mb/s; Data depth: 4000 bit

Page 9 of 33

9248 163 Street

Surrey, BC V4N 3C9

604-637-2167

info@triarchytech.com

16QAM modulation in Demo key: Data rate rage: 4.4kb/s to 9.6Mb/s; Data depth: 4000 bit

* Define the I&Q data file, study different I&Q pattern, internal I&Q engine will generate the most of digital

modulation; Such as 64QAM.

1.4.9 Specification for I&Q external modulation (not suit for TSG4G1)

Baseband signal bandwidth: 500MHz

I&Q signal level: 1Vpp

I&Q port impedance: 200 ohm

* any kind of modulation will be depended on the input of I&Q signal

1.4.10 Specification for LF output

SIN Waveform in Demo: Waveform pattern length: 72 point.

Frequency range: 15.4Hz to 33.3 KHz

Signal level: 1VPP

Triangle Waveform in Demo: Waveform pattern length: 36 point

Frequency range: 30.8Hz to 66.6 KHz

Signal level: 1VPP

Spiral waveform in Demo: Waveform pattern length: 720 point

Frequency range: 1.5Hz to 3.3 KHz

Signal level 1VPP

Total I&Q raw data length: 4Kb

I&Q points range: 30 to 65000

*Define the I&Q data file, study different pattern. internal I&Q engine will generate most of the signal waveform.

1.4.11 Specification for Pulse signal output

Pulse output level: 3.3V

Pulse repeat time: 400uS to 20s

Pulse duration time: 10us to 5S

Multiple pulse number: 2~250

Multiple pulse delay: 100us~5s (last pulse cannot be overlaid with first pulse)

2 Getting Started

2.1 Install PC Application

Open the CD, go into the SW file folder, you can find setup.exe and Document folder.

If you want copy the setup.exe to any PC any folder to install the program, please make sure that Document folder shall

be copied and located at same folder as setup.exe file.

When you finished the installation, the TSG ICON will be shown on the desk

Page 10 of 33

9248 163 Street

Surrey, BC V4N 3C9

604-637-2167

info@triarchytech.com

After installation, the program file will be installed at program file folder.

C:\Program Files (x86)\Triarchy Tech\USB Vector Signal Generator

The application data will be generated at Document folder:

C:\Users\Username\Documents\Triarchy Tech\TSG Signal Generator

Customer need to check the application data at document folder.

Calibration folder stores the calibration file. There multiple calibration files in the folder. You can generate new

calibration file and stored in same folder.

Hardcopy folder: stores the image file which generated by hardcopy key.

Hopping folder: stores the hopping files.

IQ Modulation folder: stores all the modulation file.

Setting folder: save file, preset, and specific setting are stored in it, then using load key to resumed the previous setting.

You can add more files into document folder, so that more modulation signal can be generated.

2.2 Uninstall PC Application

Uninstall TSG ICON, click it to uninstall.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Triarchy Technologies Wechselrichter Handbücher

Triarchy Technologies

Triarchy Technologies VSG6G1C Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung