TRIBUTARY Sawtooth II Bedienungsanleitung
AIRE, P.O. Box 186, Meridian, ID 83680
Ph: 208-888-1772 or 800-247-3432 | Fax: 208-884-2089 or 800-701-2473
Sawtooth II
!CAUTION
ALWAYS WEAR A GOVERNMENT APPROVED FLOATATION DEVICE.
KNOW THE LIMITS OF YOUR ABILITY AND THE LIMITS OF YOUR EQUIPMENT!
The Sawtooth II Contains:
1 - Sawtooth II
2 - Deluxe Cheetah Chairs 1 - Repair Kit
1 - Skeg
Repair Kit Includes:
2 - 6” x 6” PVC Material
2 - 6” x 6” Vinyl
1 - 6” x 6” Urethane Coated Nylon
1 - Summit 2 Valve Wrench
1 - Summit 2 Valve Adapter
1 - Vinyl Tubing Adapter
3 - Type B Adhesive Patches
2 - Alcohol Prep Pads
1 - Tear Aid Instruction Sheet
1 - Piece Sandpaper
**Glue Not Included**
Item Needed for Inflation: (not included)
1 - Pump
Skeg Installation
Items needed:
1 - Sawtooth II 1 - Skeg
1. With the boat deflated, align the skeg as shown in Figure 1.
2. Insert the long end of the skeg base into the pocket. Slide it all the way in toward the front of the kayak.
(Figure 2)
3. Next, insert the rear of the skeg base into the rear slot and slide it back until it stops. (Figure 3)
Inflating the boat to operating pressure will lock the skeg in place.
Figure 1 Figure 2 Figure 3
Inflation
Items needed:
1 - Sawtooth II
1 - Summit 2 Valve Adapter 1 - Vinyl Tubing Adapter
1 - Pump (not included)
Inflate the Sawtooth II using a hand, foot or an electric pump designed for inflatable
boats. If using an electric pump for initial inflation, a hand pump must be used to top
off the kayak.
To inflate:
1. Remove the dust cap from the valve.
2. Push and turn the valve stem 1/4 turn to the left. This positions the valve
stem in the up or closed position. Having the valve stem in the closed position
allows air to be pumped into the chamber and will prevent the air from
escaping. See Figure 1
3. Connect the clear vinyl valve adapter to the pump hose and to the gray
Summit 2 valve adapter and insert it into the boat’s valve. A 1/4 turn to the
right will lock the adapter to the valve. See Figure 2
4. Inflate the chamber to a soft pressure.
5. Repeat procedure for all chambers.
6. Once all chambers are softly inflated, top off all chambers to 2.5 psi.
Do not over inflate the kayak.
Inflation Pressure: A good rule for gauging the proper pressure is to push down with
your thumb at the center of the tube. If you can deflect about a half an inch from the
top plane of the tube, it will be close to 2.5 psi.
To deflate:
Depress the valve stem and turn it 1/4 turn to the right (clockwise). This positions the
valve stem in the down or open position and will allow air to escape freely from the
chamber. See Figure 3
!CAUTION
Changes in air temperature and elevation could cause the air inside the boat to expand which could cause the kayak
to burst. Always release some air when these conditions occur.
Never leave your boat sitting in direct sunlight when it is out of the water.
Seat Installation
Items needed:
1 - Sawtooth II 2 - Deluxe Cheetah Chairs
1. Find the seat locations that best suit you with the boat inflated. Position the chairs between the drain holes,
spacing so that each paddler is seated comfortably and weight is evenly balanced to slightly forward heavy.
(See photo on page 1 for approximate locations.) Installing the seats is easiest when the boat is deflated.
2. Connect the webbing located at the four corners of the Deluxe Cheetah Chair to the cargo loops along the
sides of the floor.
3. Connect the flip strap buckle to the top right side of the seat, loop it under the boat and finally secure the
buckle to the top left side of the seat. This strap can be used to right the kayak if the kayak capsizes as well
as providing additional support for the seat back.
4. Repeat Step 2 and 3 for remaining seat.
Transporting
To avoid excessive wear and extend the life of this craft we recommend transporting this craft in an AIRE Small Kayak
Bag or cover with clean, dry tarp. Do not load other equipment, particularly heavy or sharp objects, on top of the craft.
If you transport your boat in an open truck bed please make sure all sharp objects are removed because more boats
are damaged in transport than on the water.
**VALVE CAPS SHOULD ALWAYS BE IN PLACE WHENEVER TRANSPORTING YOUR BOAT.**
Cleaning and Maintenance
Your inflatable boat is constructed with high quality materials and superior workmanship however, as with all outdoor
equipment, proper cleaning and maintenance will extend the use of the product and allow it to perform better. Most
damaging to your inflatable boat are extended UV exposure, insect repellents, plus mold and mildew. To keep your
boat performing its best please following these simple instructions.
•Do not set your boat on sharp objects. •Do not over inflate your boat.
•Keep the zippers clean. •Clean the boat with soap and water.
•Allow the boat to drain properly so it can be stored dry.
Storage
Short Term Storage - Allow to air dry, deflate and roll loosely
Long Term Storage - Store your boat dry and clean. After use, rinse off all debris and allow the boat to air dry on soft
pressure and out of direct sunlight. Residual water inside the bladders/airecells will not damage the boat. Store the
boat in a cool, dry place out of sunlight and away from exhaust fumes. If you store your boat inflated you should be
able to pinch an inch of material.
Basic Trouble Shooting
1. Valve does not retain air when pump is removed.
•Make sure that the valve stem is in the up and closed position.
•Clear any debris that might be preventing the valve from sealing. This can be accomplished by either
pumping quick bursts of air into the valve or removing the core valve assembly and cleaning the edge of
the rubber diaphragm with a cotton swab and denatured alcohol.
•Make sure that the core valve assembly is tight. Tighten valve if necessary.
2. Tube becomes soft after inflation process.
•Determine which air chamber is soft. Make sure the valve is functioning correctly, with no signs of
leaking. (See # 1 above.)
•Find the hole in the airecell and patch with the Tear Aid patch.
3. Tube is puckered or shows a void when inflated.
•The airecell might be misaligned. Deflate the tube(s) and as they are brought back up to pressure,
manipulate the tube(s) to free the airecell as it inflates. If this does not fix the problem, deflate the boat,
open the zipper and adjust the airecell.
4. Zipper is difficult to operate.
•Use a combination of soap, water and an old toothbrush to clean and clear the zipper of debris.
5. Tear Aid patch does not stick to airecell.
•Make sure the area to be patched is dry and clean. Use the alcohol pad to prep the area, if necessary.
This boat contains a starter repair kit that includes equipment for basic repairs.
The Repair Kit Includes:
2 - 6” x 6” PVC Material
2 - 6” x 6” Vinyl
1 - 6” x 6” Urethane Coated Nylon
1 - Summit 2 Valve Wrench
1 - Summit 2 Valve Adapter
1 - Vinyl Tubing Adapter
3 - Type A Adhesive Patches
2 - Alcohol Prep Pads
1 - Tear Aid Instruction Sheet
1 - Piece Sandpaper
**Glue Not Included**
Here is a list of items, not included, which you should strongly consider keeping with your repair kit at all times.
*1/4 Pint Stabond 2-Part Adhesive
Popsicle Stick or Tongue Depressor
Scissors or Knife
Small Paintbrush
Roller
MEK Solvent
Towel
Duct Tape
Old Toothbrush
Standard Screwdriver
*It is recommended that the glue be replaced every year or after use.
The Ultimate Extended Trip Repair Item
The ultimate repair part for any boat is an extra airecell.
Repair Tips
Prior to opening the boat’s zippers, make sure they are clean and clear of any debris so that they will operate freely,
by cleaning the zippers with soapy water and an old toothbrush.
When patching the airecell, apply the patch to the outside of the airecell. When patching the PVC shell, apply the
patch on the inside of the PVC. The airecell patch is for air retention. The PVC shell patch protects the airecell patch
as well as prevents the hole from tearing further.
Adhesive Patch Repair
Items needed:
Towel
Alcohol Prep Pad Type B Adhesive Patch
Tear Aid Instruction Sheet
For most repairs, the airecell does not need to be removed completely.
1. Locate the hole in the boat and access that area of the airecell and outer skin by opening the zipper.
2. Using a towel, dry the area to be worked on.
3. Clean area to be worked on with alcohol prep pad and let the area air dry.
4. Peel backing paper off Type B Adhesive Patch and apply patch over punctured area.
(See Tear Aid instruction sheet for more details.)
5. Press and rub patch so that the patch seals completely and is without bubbles.
6. Carefully close the zipper and replace the split ring. The boat can then be inflated for use.
Glue Repair
Items needed:
Scissors or knife
Standard Screwdriver
Roller
Stabond 2-part adhesive
Sandpaper
Popsicle stick
Small brush
PVC Material or Urethane Material
MEK or Alcohol Prep pads
For most repairs, the airecell does not need to be removed completely.
When patching the airecell, apply the patch to the outside of the airecell. When patching the PVC shell, apply the
patch on the inside of the PVC.
1. Locate the hole in the boat and access that area of the airecell and outer skin by opening the zipper.
2. Using a towel, dry the area to be worked on.
3. Cut a patch of fabric at least two inches large in length and width than the puncture, hole, or tear.
4. Clean the area to be patched (using MEK or alcohol prep pads).
5. Rough up both the patch and the area to be patched with the sand paper.
6. After opening the 2-part adhesive, prepare the Stabond glue by pouring the entire contents of the glass jar
into the metal can and stir using a popsicle stick or tongue depressor.
7. Apply an even coat of glue with a small brush to both the patch and the area to be repaired and let dry
completely, approximately 10-15 minutes.
8. Apply a second coat of glue, and let dry 5 minutes or until tacky. If the glue is too dry, reactivate it with a
small amount of MEK.
9. Place the patch over the hole or tear, and press together. Using a roller or another blunt object press from the
center of the patch to the edges to seal the patch to the airecell or outer skin. Make sure that the patch seals
completely and is without bubbles.
10. Let the glue cure at least one hour before inflating (overnight if possible is best). Do not inflate to full pressure
on the same day of the repair.
Extensive Repairs
If you have a major rip or tear in your boat that is beyond your abilities to repair, please contact AIRE at 800-247-3432
for a Return Authorization number. Please put a brief note with your contact information and a detailed description of
the repairs necessary inside the box and ship the package to the address below with the RA number clearly written on
the outside of the box. For your protection, please ship the boat with a service that provides a tracking number.
Warranty
This warranty covers defects in materials and workmanship only for a period of 1 year from the date of purchase for
the original owner for non-commercial use.
AIRE reserves the right to determine whether to repair or replace any product covered by this warranty and the right to
replace any discontinued models with current models when necessary. Colors may vary between original and
replacement parts.
If you have any questions, please contact us at
AIRE, 2021 E. Wilson Lane, Meridian, ID 83642
Ph: 208-888-1772 or 800-247-3432
www.aire.com
Thank you for choosing Tributary products.
Inhaltsverzeichnis
Andere TRIBUTARY Boot Handbücher
Beliebte Boot Handbücher anderer Marken
Raymarine
Raymarine ST70 Instrument Bedienungsanleitung
Pro-Line Boats
Pro-Line Boats Pro Line 19 Sport Bedienungsanleitung
Jeanneau
Jeanneau CAP CAMARAT 8.5 CC Bedienungsanleitung
Tiara Yachts
Tiara Yachts C49 2024 Bedienungsanleitung
Monterey Boats
Monterey Boats Sport Yacht 330 Bedienungsanleitung
J
J 105 Bedienungsanleitung
PURSUIT
PURSUIT OS 335 Bedienungsanleitung
Boston Whaler
Boston Whaler CONQUEST 345 Bedienungsanleitung
Jeanneau
Jeanneau SUN ODYSSEY 41 DS Bedienungsanleitung
Meridian
Meridian 490 Pilothouse Bedienungsanleitung
Advanced Elements
Advanced Elements AdvancedFrame Expedition AE1009 Bedienungsanleitung
Robo Marine Indonesia
Robo Marine Indonesia GEOMAR Bedienungsanleitung
