Trident NM14 Bedienungsanleitung

Scrubbing machine

ORIGINAL INSTRUCTIONS DOC. 10075414 - Ver. AA - 11-2017

Use and Maintenance manual

CONTENTS

The following symbols are used to indicate

any potentially hazardous situations. Always

read this information carefully and take the

necessary precautions to protect any people

and/or objects that may be present.

Operator cooperation is paramount for accident

prevention. No accident prevention programme

can be e󰀨ective without the full cooperation

of the person directly responsible for the

machine's operation. Most accidents that occur

at the workplace, during work activities, or while

in transit, are caused by the failure to respect

the most basic safety regulations. An attentive,

careful operator is most e󰀨ective guarantee

against accidents and is fundamental in order

to implement any prevention programme.

DANGER: Indicates an imminent danger

that could cause serious injury or death.

WARNING: Indicates a probable

dangerous situation that could cause

serious injury or death.

CAUTION: Indicates a probable

dangerous situation that could cause

minor injuries.

ATTENTION: Indicates a probable

dangerous situation that could damage

objects.

N.B.: Indicates a note regarding essential

or useful functions.

CONSULTATION: Indicates the need

to consult the Operator's Manual before

performing any operation.

GENERAL SAFETY

REGULATIONS

CONTENTS................................................................................3

GENERAL SAFETY REGULATIONS ........................................3

RECHARGING THE BATTERIES.................................................... 4

USING THE MACHINE ....................................................................... 4

DEACTIVATION OF THE MACHINE................................................... 6

MAINTENANCE .................................................................................. 6

TRANSPORT ...................................................................................... 7

DISPOSAL........................................................................................... 7

SYMBOLS USED IN THE MANUAL .........................................8

SYMBOLS USED ON THE MACHINE ......................................8

PURPOSE AND CONTENT OF THE MANUAL ........................8

TARGET GROUP.......................................................................8

PRESERVATION OF THE USER ..............................................8

ON CONSIGNMENT OF THE MACHINE ..................................8

INTRODUCTORY COMMENT ...................................................8

IDENTIFICATION DATA.............................................................8

TECHNICAL DESCRIPTION .....................................................8

SAFETY .....................................................................................8

SERIAL NUMBER PLATE .........................................................8

SPARE PARTS...........................................................................9

HANDLING THE PACKAGED MACHINE .................................9

HOW TO UNPACK THE MACHINE...........................................9

HOW TO MOVE THE MACHINE ...............................................9

BATTERY TYPE.........................................................................9

RECHARGING THE BATTERY .................................................9

MACHINE PREPARATION ......................................................10

PREPARING TO WORK ..........................................................10

WORK ......................................................................................11

AT THE END OF THE WORK..................................................11

MAINTENANCE.......................................................................12

TROUBLESHOOTING.............................................................13

DISPOSAL ...............................................................................14

EC DECLARATION OF CONFORMITY ..................................14

DANGER:

• If the battery charger power cable is damaged or broken, it should be replaced by the

manufacturer, by authorised service personnel or else by a qualied person, in order to protect

against hazards.

• Keep sparks, ames, and incandescent materials at a safe distance from the batteries.

• Before charging check that the electric cable that connects the battery charger to the batteries

is not damaged, and if it is damaged do not use it and contact technical assistance.

• Before using the battery charger, check that the electric socket that connects the battery

charger to the mains is not damaged, and if it is do not use it and contact an authorised

service technician or another qualied person, in order to avoid and hazardous situations.

• Do not disconnect the battery charger cable from the machine socket when the battery charger

is operating. This is necessary to prevent electric arcs forming. To disconnect the battery

charger when charging, rst disconnect the power cable from the mains socket.

WARNING:

• Do not use incompatible battery chargers since they could damage the batteries and potentially

cause a re. To charge the battery only use the detachable power pack provided with this

machine.

• Keep the battery charger's cable at a safe distance from any hot surfaces.

• Carefully read the user manual of the battery charger you want to use before recharging.

• Do not disconnect the battery charger from the mains socket with wet hands.

RECHARGING THE BATTERIES

DANGER:

• In the event of danger, quickly press the machine's main switch and remove the battery from

the battery compartment.

• Never collect gases, explosive/inammable liquids or powders, nor acids and solvents! These

include gasoline, paint thinners and fuel oil (which, when mixed with the vacuum air, can form

explosive vapours or mixtures), and also non-diluted acids and solvents, acetones, aluminium

and magnesium powders. These substances may also corrode the materials used to construct

the machine.

• If the machine is used in dangerous areas (e.g. petrol stations), the relative safety standards

must be observed. It is forbidden to use the machine in environments with a potentially

explosive atmosphere.

WARNING:

• The machine must be exclusively used by authorised, trained personnel.

• Do not use the machine on surfaces with a slope greater than the one indicated on the serial

number plate.

• The machine is not suitable for cleaning rough or uneven oors. Do not use the machine on

slopes.

• In the event of a re, use a powder extinguisher. Do not use water.

• Adapt the speed to the adhesion conditions.

• In order to prevent the unauthorised use of the machine, the power supply must be interrupted,

switch the machine o󰀨 using the main switch, remove the battery from the battery compartment.

USING THE MACHINE

• Do not use the machine without the requisite knowledge and authorisations.

• Do not use the machine if you have not read and understood the following user manual.

• Do not use the machine under the inuence of alcohol or drugs.

• Do not use the machine when using a mobile phone or other types of electronic devices.

• Do not use the machine if it is not working correctly.

• Do not use the machine in areas where there are inammable vapours or liquids or combustible

powders.

• Do not use the machine in areas that are too dark to see the controls or operate the machine

safely, unless the work lights or the front headlights are on.

CAUTION:

• This machine must not be used by people (including children) with reduced physical, sensorial

and mental capabilities, or by people without any experience or knowledge, unless they have

been controlled and instructed in the use of the machine by those responsible for their safety.

Children must be supervised to ensure they do not play with the machine.

• During the working of the machine, pay attention to other people and especially to children.

• The machine must only be powered with a voltage equal to that shown on the serial number

plate.

• Read the labels on the machine carefully. Do not cover them for any reason, and replace them

immediately if they become damaged.

• The machine must only be used and stored in an enclosed or covered environment.

• The machine must not be used or stored outdoors in damp conditions or directly exposed to

rain.

• The machine does not cause harmful vibrations.

• Use the machine only in the manner described in this manual.

• Do not collect inammable or steaming refuse, like cigarettes, matches and hot embers.

• Always follow the instructions on the containers for mixing, using and disposing of chemical

substances.

ATTENTION:

• Always take appropriate measures to protect any individuals and/or objects that may be

present while using this machine.

• Be careful to avoid collisions with shelving or sca󰀨olding, above all if there is a risk of objects

falling from heights.

• Do not place any liquid containers on the machine.

• The machine must only be used under temperature conditions ranging from 32°F to +104°F.

• When using detergents to clean the ooring, always follow the instructions and respect the

warnings indicated on the containers' labels.

• Always use appropriate gloves and protective equipment when handling the detergents used

to clean the oor.

• Avoid working with the brushes when the machine is standing still, so as to avoid damage to

the oor.

• Do not allow any objects to penetrate into the machine's openings. Do not use the machine is

the openings are obstructed.

• Keep the machine's openings free of any dust, lint, hairs, or any other foreign materials that

could reduce the airow.

• Do not remove or alter any labels a󰀩xed to the machine.

• Use only the brush supplied with the machine or those specied in the following manual.

Using other brushes compromises the safety of the machine and its operator.

• Before starting work check that there are no leaks.

• Before starting work check that all the safety devices have been installed and are working

correctly.

• Take all due precautions so that hair, jewellery, loose clothing do not get entangled in the

machine's moving parts.

• Only use the machine in well-lit areas.

WARNING:

• Always protect the machine against sunlight, rain, and other atmospheric agents, both while it

is stationary and while it is in function. Store the machine in a dry, sheltered place: this machine

is only designed for use under dry conditions, and must not be used or stored outdoors under

humid conditions.

• Do not park the machine near combustible materials, powders, gases or liquids.

• Stop the machine on at ground.

• Switch o󰀨 the machine and remove the battery from the battery compartment.

• If the machine is left unattended, it must be protected from any accidental movements

CAUTION:

• In order to prevent the unauthorised use of the machine, the power supply must be interrupted,

switch the machine o󰀨 using the main switch, remove the battery from the battery compartment.

ATTENTION:

• The machine must only be stored under temperature conditions ranging from 32°F to +104°F.

The humidity level must be between 30% and 95%.

DEACTIVATION OF THE MACHINE

DANGER:

• In order to avoid short-circuits when working in the vicinity of electrical components, do the

following: avoid the use of non-insulated tools; do not place or allow metallic objects to fall

upon the electrically powered components; remove any rings, watches and/or clothing with

metallic parts that might come into contact with the electrically powered components.

WARNING:

• Read all the relevant instructions carefully before performing any maintenance/repair

operations.

• If the machine does not work properly, check this is not caused by failure to carry out routine

maintenance. Otherwise, ask for intervention of the authorised technical assistance centre.

MAINTENANCE

The machine must not be transported or parked in its rest position

when the solution tank and recovery tank are full.

• Restore all electrical connections after any maintenance interventions.

CAUTION:

• For any maintenance work, switch the machine o󰀨 using the main switch, remove the battery

from the battery compartment.

• Avoid contact with moving parts. Do not wear loose clothing or jewellery and tie up long hair.

ATTENTION:

• Never tamper with the machine's protection devices for any reason; always follow the supplied

routine maintenance instructions scrupulously.

• If any issues are encountered while using the machine, check to make sure that these are

not due to a lack of proper maintenance. Otherwise, request the intervention of authorized

personnel or an Authorized service centre.

• When replacing parts, ask for ORIGINAL spare parts from a Dealer or an authorised retailer.

• In order to ensure the machine is safe to use and operates properly, carry out the maintenance

work specied in this manual.

• Do not clean the machine with direct or pressurized jets of water, or with corrosive substances.

• Have the machine checked by an authorised technical assistance centre every year.

• When disposing of consumable materials, observe the laws and regulations in force. Once

the machine has reached the end of its service life, the materials contained within it must be

disposed of in an appropriate manner, keeping in mind that the machine itself has been built

using fully recyclable materials.

• All repairs should be carried out by qualied personnel.

• Do not physically modify the machine's design features.

• Use spare parts provided by authorised service centres.

• Wear personal protective equipment as required and as recommended in the manual.

WARNING:

• Drain both tanks before transport.

• Move the squeegee to the rest position.

• Remove the battery from the battery compartment.

TRANSPORT

ATTENTION:

• The machine should not be abandoned at the end of its working life because of the presence

of toxic-harmful substances in it, which are subject to regulations that regulate their disposal

in special centres.

DISPOSAL

Protective gloves symbol:

Always wear protective gloves, to avoid the risk of serious injury to your hands.

Warning symbol:

Carefully read the sections marked with this symbol and observe the indications, for the safety

of the operator and the machine.

Covered place symbol:

The operations preceded by this symbol must always be carried out in a dry, covered area.

Symbol for squeegee movement to “work position”:

Indicates the rotation direction of the squeegee control knob in order to bring the squeegee

rubbers into contact with the oor.

Symbol of the open book with i:

Indicates the need to consult the instruction manual.

Main switch symbol:

Used on the central rear of the machine to indicate the main switch.

Recycling symbol:

Tells the operator to carry out the operations in compliance with environmental regulations in

force in the place where the machine is being used.

Tank drainage symbol:

Informs the operator that the recovery tank must be emptied every time the solution tank is

lled.

Recycling symbol:

Carefully read the sections marked with this symbol in order to ll the solution tank correctly.

Tool symbol:

Indicates the need to use tools not included in the supply.

Lifting point symbol:

Used to indicate the location of the elements for lifting the machine or else moving the mobile

parts of the machine.

“OPEN” symbol:

Used on the upper part of the appliance to indicate the position of the handle for opening the

front carter.

Warning symbol not to rotate the machine:

indicates that the machine must not be rotated when the tanks are full.

Explosion risk symbol:

Indicates that the battery may explode in certain conditions, if not handled in accordance with

the directives indicated in the manufacturer's manual.

The descriptions contained in this document are not binding. The company therefore reserves the

right to make any modications at any time to elements, details, or accessory supply, as considered

necessary for reasons of improvement or manufacturing/commercial requirements. The reproduction,

even partial, of the text and drawings contained in this document is prohibited by law.

The company reserves the right to make any technical and/or supply modications. The images

are shown as reference only and are not binding as to the actual design and/or equipment.

Symbol of the open book:

used to tell the operator to read the manual before using the machine.

Solenoid valve switch symbol:

Used on the rear of the machine to indicate the solenoid valve control switch.

Disposal symbol:

Carefully read the sections marked with this symbol for machine disposal.

Symbol for squeegee movement to “idle position”:

Indicates the rotation direction of the squeegee control knob in order to raise the squeegee

rubbers o󰀨 the oor.

SYMBOLS USED IN THE MANUAL

SYMBOLS USED ON THE MACHINE

PURPOSE AND CONTENT OF THE MANUAL

The aim of this manual is to provide customers with all the information needed to use the machine

in the safest, most appropriate and most autonomous way. This includes information concerning

technical aspects, safety, operation, downtime, maintenance, spare parts and scrapping. The operators

and qualied technicians must carefully read the instructions in this manual before carrying out any

operations on the machine. If in doubt about the correct interpretation of instructions, contact your

nearest Customer Service Centre to obtain the necessary clarications.

TARGET GROUP

This manual is written both for operators and for qualied machine maintenance technicians. Operators

must not perform operations that should be carried out by qualied technicians. The manufacturer is not

liable for damages resulting from failure to comply with this prohibition.

PRESERVATION OF THE USER

The following document must be stored in its special pouch close to the machine, protected from liquids

and anything else that could compromise its legibility.

ON CONSIGNMENT OF THE MACHINE

When the machine is consigned to the customer, an immediate check must be performed to ensure all

the material mentioned in the shipping documents has been received, and also to check the machine

has not su󰀨ered damage during transportation. If this is the case, the carrier must ascertain the extent

of the damage at once, informing our customer service o󰀩ce. It is only by prompt action of this type that

the missing material can be obtained, and compensation for damage successfully claimed.

INTRODUCTORY COMMENT

Any machine can only work properly and e󰀨ectively if used correctly and kept in full working order

by carrying out the maintenance operations described in the attached documentation. We therefore

suggest you read this instruction booklet carefully and read it again whenever di󰀩culties arise while

using the machine. If necessary, remember that our assistance service (organised in collaboration with

our dealers) is always available for advice or direct intervention.

IDENTIFICATION DATA

For technical assistance or to request replacement parts, always give the model, the version and the

serial number (written on the relevant plate).

TECHNICAL DESCRIPTION

The TRIDENT NM14 is a oor scrubbing machine that cleans a wide range of ooring and dirt types

by means of the mechanical action of a cylindrical brush and the chemical action of a water-detergent

solution, collecting the dirt as it moves forward that has been removed and the detergent solution that

has not been absorbed by the oor. The machine must only be used for this purpose.

TECHNICAL DESCRIPTION

This machine was designed and built for the cleaning (scrubbing and drying) of smooth, compact

ooring in the commercial, residential and industrial sectors by a qualied operator in proven safety

conditions. The machine is not suitable for cleaning rugs or carpets. The machine is only suitable for

use in closed (or at least covered) places.

WARNING: The machine is not suitable for use in the rain, or under jets of water.

IT IS FORBIDDEN to use the machine for picking up dangerous dusts or inammable liquids in places

with an explosive atmosphere. In addition, it is not suitable as a means of transport for people or

objects.

SAFETY

Operator cooperation is paramount for accident prevention. No accident prevention programme can

be e󰀨ective without the full cooperation of the person directly responsible for machine operation. The

majority of occupational accidents that happen either in the workplace or whilst moving are caused by

failure to respect the most basic safety rules. An attentive, careful operator is most e󰀨ective guarantee

against accidents and is fundamental in order to implement any prevention programme.

SERIAL NUMBER PLATE

The serial number plate is located in the power supply battery

compartment on the rear part of the machine, indicating its general

characteristics, and in particular the serial number. The serial

number is a very important piece of information and should always

be provided together with any request for assistance or when

purchasing spare parts.

TECHNICAL DATA U/M TRIDENT

NM14

Total power W 150

Working width IN 13,4

Working capacity, up to ft2/h 7320

Central brush (number / (diameter x length)) No. /(Øin x in) 1 / (4,3 x 13,4)

Brush motor (rated) V/W 24 / 50

Vacuum motor (rated) V/W 24 /100

Maximum gradient % 2

Solution tank capacity gal 0,32

Recovery tank capacity gal 0,26

Machine body length in 17

Machine body height in 8,5

Overall dimensions in standby position (L x h x w) in 15,5x51x17,5

Overall dimensions in idle position (L x h x w) in 15,5x36x14,4

Rated battery voltage V / mAh 25.55 / 5200

Battery weight lb 2,2

Machine weight when empty (machine + brush + squeegee) lb 20

Machine weight in transport (machine + battery + brush +

squeegee) lb 22

Machine weight ready to use (machine + battery + detergent

solution + brush + squeegee) lb 25

Sound pressure level (ISO 11201) - Lpa dB (A) <70

Uncertainty Kpa dB (A) 1.5

Hand vibration level (ISO 5349) m/s2< 2.5

Vibration measurement uncertainty 4%

SPARE PARTS

HANDLING THE PACKAGED MACHINE

The machine is contained in specic packaging, and since

the packaging elements (plastic bags, staples, etc.) are

a potential source of danger, they should not be left within

the reach of children, disabled persons, etc. The machine's

overall weight including packaging is 18 Kg.

The packaging dimensions are as follows:

U/M TRIDENT NM14

Ain 10,6

Bin 19,2

Cin 27,5

HOW TO UNPACK THE MACHINE

The procedure for unpacking the machine is as follows:

1. Place the lower part of the outer packaging in contact with the oor.

CAUTION: Use the pictograms printed on the box as reference.

2. Open the outer box.

3. Remove the accessories from the box and carefully lay them on the ground.

4. Take the machine out of the box.

ATTENTION: it is recommended that all the packaging components be kept for any future

machine transportation.

CAUTION: these operations must be carried out using protective gloves to avoid any possible

contact with the edges or tips of metal objects.

HOW TO MOVE THE MACHINE

The procedure for the safe transportation of the machine is the following:

1. If the machine is running, switch it o󰀨 by pressing the main switch (1) (Fig.1).

2. Make sure the recovery tank is empty. If it isn't, empty it completely.

3. Make sure the solution tank is empty, otherwise empty it completely.

4. Remove the battery (2) from the battery compartment; to free the battery, shift the stop lever (3) in

the direction of the arrow (Fig.2). Remove the battery from the machine using the handle moulded

on it (Fig.3).

The machine must not be transported or parked in its

rest position when the solution tank and recovery

tank are full.

5. Block the handlebar in the horizontal position. Rest your foot on the body of the machine to prevent

it from tilting, then push the handle away from you until it snaps into the horizontal position (Fig.4).

CAUTION: do not rest your foot on the main switch.

6. Rotate the stop lever of the command handlebar (4) in the direction of the arrow (Fig.5).

7. Close the command handlebar, pushing the handle (5) towards the body of the machine (Fig.6).

8. Rotate the stop lever of the command handlebar (4) in the direction of the arrow (Fig.7).

9. To lift the machine o󰀨 the oor, use the handle (6) on its rear (Fig.8)

CAUTION: When transporting on vehicles, secure it rmly in place in compliance with the

directives in force so that it cannot slide or tip over.

CAUTION: these operations must be carried out using protective gloves to avoid any possible

contact with the edges or tips of metal objects.

BATTERY TYPE

To power the appliance, use only the battery supplied in the packaging or one supplied by a specialised

technician. OTHER BATTERY TYPES CANNOT BE USED. The machine is powered by a lithium-ion

battery. The battery compartment can accommodate a single battery slot at 25.55V.

WARNING: for the maintenance and disposal of the battery, refer to the document supplied by

the battery manufacturer.

RECHARGING THE BATTERY

The battery must be charged prior to the rst use, and when it doesn't provide enough power for tasks

that could formerly be performed without di󰀩culty. To recharge the battery, proceed as follows:

1. Take the machine to the designated place for charging the battery.

WARNING: the place for charging the battery should be suitably ventilated.

2. If the machine is running, switch it o󰀨 by pressing the main switch (1) (Fig.1).

3. Block the handlebar in the vertical position.

CAUTION: during this operation, do not rest your foot on the machine.

4. Read the battery charger manual that comes with the machine for inserting the power plug (2) into

the power pack (3) (Fig.2).

CAUTION: before connecting the battery charger to the socket, make sure the characteristics of

the mains supply correspond to those of the battery charger.

WARNING: the battery charger must only be used in a covered place.

5. Connect the power plug (2) to the mains supply.

WARNING: make sure the green LED (4) on the battery charger lights up when you enable the

battery charger base circuit (Fig.3). This LED indicates that the battery charger circuit is

correctly powered.

6. Remove the cap (5) covering the battery power socket (Fig.4).

7. Insert the battery charger power cable plug (6) in the socket (7) on the battery (Fig.5).

WARNING: make sure the green LED (4) on the battery charger lights up when you enable the

charger (Fig.3). This LED indicates that the battery charger circuit is correctly powered.

OFF 2

2 3

OFF 4

POS. CODE QTY DESCRIPTION

1 440974 1 BATTERY

2 441033 1 BATTERY CHARGER

3 439888 1 DETERGENT SOLUTION FILTER

4 441025 2 ANTI-DUST FILTER

5 224800 1 SQUEEGEE RUBBER KIT

6 224615 1 CONTROL HANDLEBAR

7 441023 1 TUBE-CLEANING BRUSH

8 227332 1 RECOVERY TANK

9 224619 1 SOLUTION TANK

440905 1 SOFT BRUSH

440904 1 HARD BRUSH

PREPARING TO WORK

CAUTION: before inserting the plug (6) in the socket (7), make sure the battery charger housing

compartment is not dirty (dust, condensation or other types of liquid).

CAUTION: make sure the red LED (4) on the battery charger lights up when you insert the plug

(6) in the socket (7). This LED indicates that the battery is recharging.

8. Perform a complete battery charging cycle.

ATTENTION: the red LED (4) remains on until the battery is fully charged. When the recharging

cycle has ended, the red LED goes o and the green LED comes on.

ATTENTION: The charger and the battery can be left connected to the power outlet. The red

LED (4) lights up when the charger occasionally tops up the battery.

ATTENTION: the red charge status LED (4) does not provide any indication of the battery

charge level.

ATTENTION: during the charging phase, the battery may overheat. This is normal and does not

mean there is any problem with the battery.

ATTENTION: if the battery used in this machine is over-charged, this may cause a risk of re,

explosion or chemical burns.

9. Once the charging cycle is completed, remove the plug (2) on the battery charger from the mains

socket.

ATTENTION: To prevent damaging to the mains socket, disconnect the plug from the mains

socket by directly pulling the plug and not the power cable.

10. Take the power cable plug (6) out of the socket (7) on the battery.

11. Insert the cap (5) that covers the battery power socket.

MACHINE PREPARATION

1. Take the package to the dedicated maintenance area.

2. Remove the machine and all the accessories from the box.

3. Insert the lower tube (1) of the control handlebar in the hole on the joint (2) (Fig.1).

4. Fix the handlebar to the joint using the screw and nut (3), making sure the hole on the handlebar

coincides with the hole on the joint (Fig.2).

N.B: the screwdriver is not supplied.

5. Block the handlebar in the horizontal position. Rest your foot on the body of the machine to prevent

it from tilting, then push the handle away from you until it snaps into the horizontal position (Fig.3).

CAUTION: do not rest your foot on the main switch.

6. Rotate the stop lever of the handlebar (4) in the direction of the arrow (Fig.4).

7. Close the command handlebar again, pushing the handle (5) towards the body of the machine

(Fig.5).

8. Rotate the stop lever of the handlebar (4) in the direction of the arrow (Fig.6).

9. Insert the battery (6) in the battery compartment (7) in the rear of the machine (Fig.7). Push the

battery until the uncoupling lever (8) locks into place.

Before beginning to work, it is necessary to:

N.B.: before beginning the rst work cycle, fully recharge the battery (read “RECHARGING THE

BATTERY”).

1. Before using the machine, make sure it is in a good, safe working condition. If everything is not in

order, the machine must not be used.

2. Rotate the handlebar so it is vertical.

CAUTION: During this operation, do not rest your foot on the machine.

3. Start the machine using the main switch (1) (Fig.1).

N.B.: If the LED of the main switch (1) (Fig.1) is lit up, this means there is electrical continuity.

4. Check the battery charge level. There are four LEDs (2) on the battery to show the charge

percentage (Fig.2). If all the LEDs are lit up, the battery is fully charged; if they are all switched o󰀨,

the battery is completely run down.

5. Switch o󰀨 the machine using the main switch (1) (Fig.3).

6. Remove the battery (3) from the battery compartment; to free the battery, shift the stop lever (4) in

the direction of the arrow (Fig.4).

7. Remove the battery from the battery compartment using the handle moulded on it (Fig.5).

8. Make sure the condition of the squeegee rubbers is suitable for the work you want to carry out. If it

isn't, perform the necessary maintenance (read “MAINTENANCE”).

9. Make sure the condition of the brush is suitable for the work you want to carry out. If it isn't, perform

the necessary maintenance (read “MAINTENANCE”).

10. Rotate the front carter (5) as far as it will go - do this with the aid of the handle (6) (Fig.6).

CAUTION: these operations must be carried out using protective gloves to avoid any possible

contact with the edges or tips of metal objects.

11. Remove the solution tank from the machine (Fig.7). Carefully place it on the oor.

12. Remove the detergent solution lling cap (7) from its seat on the solution tank (Fig.8).

13. Fill with clean water, at a temperature no higher than 50°C and no lower than 10°C.

14. Add the liquid detergent to the solution tank in the concentration and manner indicated on the

detergent manufacturer's label.

N.B.: The formation of excess foam could damage the vacuum motor, so use only the minimum

amount of detergent that is necessary.

N.B.: always use detergents whose manufacturer's label indicates their suitability for scrubbing

machines. Do not use acid or alkaline products or solvents without this indication. Acid or

alkaline maintenance detergents can be used, as long as they have pH values between four and

ten, and do not contain : oxidising agents, chlorine or bromine, formaldehyde, mineral solvents.

CAUTION: protective gloves should always be worn before handling detergents or acidic or

alkaline solutions, to avoid serious injury to the hands.

N.B.: always use low-foam detergent. To avoid the production of foam, put a minimum quantity

of anti-foam liquid in the recovery tank before starting to clean. Do not use pure acids.

15. Replace the detergent solution lling cap (7) in its seat on the solution tank (Fig.9).

N.B.: it is good practice to empty the recovery tank every time you top up the solution tank level.

16. Insert the solution tank in the machine (Fig.10).

17. Rotate the front carter (5) as far as the work position - do this with the aid of the handle (6) (Fig.11).

18. Insert the battery in the battery compartment in the rear of the machine.

1 2 3

4 5

11 2

31 2

OFFON

4 5

Inhaltsverzeichnis

Andere Trident Schrubber Handbücher

Trident

Trident T20SC PRO Bedienungsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung

REMS

REMS Twist Bedienungsanleitung