Trigon Trinity Bedienungsanleitung

QUICK START GUIDE FOR AUDIO PLAYER

Trinity

Contents

1 Safety advice.....................................................................................................................3

2 Commissioning..................................................................................................................4

2.1 Operating elements on the front side.........................................................................4

2.2 Connectors on the back side......................................................................................4

2.3 Wiring..........................................................................................................................5

2.4 stablish LAN connectivity.........................................................................................5

3 Playback music from different sources..............................................................................7

3.1 Playback music from a connected USB device..........................................................7

3.2 Playback a radio channel............................................................................................7

3.3 Playback an Audio CD.................................................................................................8

3.4 Playback music from a connected device ..................................................................9

4 Rip an Audio CD to a USB device.....................................................................................9

5 Technical details..............................................................................................................11

1 Safety instructions

Trigon Elektronik GmbH does not assume any liability for damages

which result from inappropriate handling or non-fulfilment of the following safety

instructions.

•The audio player must not be subjected to shocks and vibrations.

•The audio player must not be placed in close proximity of strong heat sources such

as heaters, ovens, high-performance illuminants, open fire etc.

•After the transport from a cool surrounding into a warm room, the audio player must

not directly be connected to the voltage.

•The audio player must not be exposed to blazing sun.

•Please make sure that there is sufficient air-circulation at the installation site.

•Also make sure not to block any ventilation slots.

•Der Audioplayer sollte nicht mit irgendeiner Flüssigkeit überschüttet werden.

•Do not pour any liquids on the audio player. Liquids must not reach the inside.

•Only use dry towels to clean the audio player.

•Never use the player without the protecting case cover.

•When opening the player, always unplug it first and make sure it is disconnected

from any electrical sources.

•Avoid your own repair attempts. Any maintenance and repair work must be

performed by specially trained staff.

•Damage caused by inappropriate handling or external intervention may void the

warranty.

•Please make sure that the audio player is switched off when plugging in connecting

cables.

•Do not place any items or electic devices onto Trinity.

Trinity is usually delivered with a wide-range power supply which can be used for a

mains voltage range between 90V and 250V AC. In case you need a different mains

voltage, please contact your retailer or Trigon company.

Commissioning

.1 Operating elements on the front side

[1] Navigation key (go back and left)

[2] Navigation key (selection key)

[3] Navigation key (go right, context menu key)

[4] Navigation key (upwards)

[5] Navigation key (downwards)

[6] USB socket

[7] Display

[8] CD drive (also for Audio CD ripping)

[9] Input for IR remote control

[10] Headphone socket

[11] Volume key (home key, mute key in home menu)

[12] RGB- light ring

[13] L Ds of volume indicator

. Connectors on the back side

[13,32] Loudspeaker sockets

[14] Main power switch

[15] Mains fuse

[16] Power socket

[17, 18] Balanced preamplifier output

[19] Unbalanced preamplifier output

[20] Output socket for recording

[21,22,23] Analogue audio inputs

[24,25] Optical S/PDIF inputs (toslink)

[26,27] Coaxial S/PDIF inputs

[28,29,30] USB sockets

[31] LAN socket

[32] 10V DC output for devices with DC switch inputs

Handmade In GERMANY

SPEAKER

LEFT CHANNEL

17 18 19 20 21 22 23

24 25 26

30 31

90 - 40V AC

10 - 350W

SPEAKER

RIGHT CHANNEL

MAIN POWER

LINE 1LINE LINE 3

D-IN-1

REC OUT

D-IN-D-IN-3D-IN-4

PRE-OUTBAL-OUT-LBAL-OUT-R

AUDIO PLAYER

TRINITY

USB USB ETHERNET

CAUTION

RISK OF L CTRIC

SHOCK DO NOT OP N

.3 Wiring

Plug the power cable into the power socket [16] of Trinity and connect the player with

power supply. Above the power socket you will find the main power switch [ 14]. Use the

power switch to turn Trinity into standby mode (switch position 1). The power L D on

the front side above the headphone [10] socket will light up.

Connect all devices with Trinity. Make sure that analogue devices are only plugged

into the LIN sockets [21, 22, 23] and that digital sources are plugged into the D-IN

sockets [24, 25, 26, 27].

Due to Trinity‘s streaming capability you should ensure LAN connectivity. In case

you would like to playback music from a USB stick or USB hard drive, plug in these

devices to the USB sockets [6, 28, 29, 30].

Plug in the loudspeakers to the sockets [13, 33] and switch on Trinity by pressing the

volume key [11].

Please note that you need to wait about 5 seconds after having turned on the main power

switch in order to stabilise the voltage of the standby power supply. Then press the

volume key [11] in order to turn Trinity fully on.

Please note that you need to wait about 5 seconds after having turned on the main power switch in order to

stabilise the voltage of the standby power supply. Then press the volume key [11] in order to turn Trinity

fully on

The power up procedure (Boot process) may take up to 1 minute. As soon as Trinity

is ready for use, the following screen will be displayed.

Home screen

.4 Establish LAN connectivity

Plug the LAN cable of your network into the LAN connection socket [31]. After a few

seconds your router should have the Trinity integrated into their local network. Now you

should determine which IP address your network router assigned to the Trinity.

Use the navigation keys [1,3,4,5] to navigate to the System function field.

Selection System

Confirm the selection with the [2] key and select the Network information field.

Select Network Information

Confirm your select with key [2] and you see the following pictuire:

The first line shows the serial number of your device.

In the second line is the IP address (e.g. 192.168.0.73). Write down this IP address.

•If you have not already done so, connect your tablet PC (or smart phone) to your

network.

•Start an internet browser on the tablet.

•nter the IP address of the Trinity in the command line of the browser (in the

example above 192.168.0.73)

The following screen appears on the screen of your table PC after the connection:

Start-up image of the remote control on the tablet or smart phone.

Note: Depending on the setting of your Internet router, the IP address may sometimes

change. If, for this reason, you are no longer able to connect to the tablet with the IP

address you have noted for the first time, check the IP again as described above.

Tip: For most routers, you can also hard-code the IP addresses of the devices on the

network so that the router does not change the IP addresses randomly, so the IP address

does not have to be reentered into the tablet over and over again.

The first line contains the two most important buttons: Music and Amp.

If you tap on these buttons these screens appears.

Screen for Buttom Music Screen for Buttom AMP

3 Playback music from different sources

3.1 Playback music from a connected USB device

(Operation at the device. Starting point is the home screen)

We connected an external USB HDD named "TOSCHIBA XT" to a USB port. The

structure of how the music was stored here can vary individually.

In our example below, the folder structure is as follows:

Jazz - Artist - List of this artist's CD's - Selected CD - Selected track

Plug in USB device.

Press key [5] to stop the playback. Keep pressing key [1] until the home screen is

displayed again or press key Volume control [1] once for home screen.

(A) Use key [4] or [5] to

navigate to the entry

Audioplayer and select with key

[2].

(B) Use key [4] or [5]to navigate

to the USB device and select

with key [2], e.g. TOSHIBA

XT.

music folder and select with key

[2], e.g. music file Jazz.

(D) Use key [4] or [5] to

navigate to the music folder of

the performer and select with

key [2].

() Use key [4] or [5] to

navigate to the music title

which you would like to

playback and select with key

[2].

(F) All following titles will be

added to the playlist and played

back.

3. Play a radio channel

( Operation at the device. Starting point is the home screen )

(In case you have played music from a USB device keep pressing key [1] until the home screen is displayed

again.)

To stop playback, press the button[5]. To get back to the start screen, press the volume

button [11] or the button [1] repeatedly until you return to the start screen.

3.3 Playback a CD

Starting point is the home screen.

Please note that it does not matter at which point of the set menu you insert the Audio CD. However, we

cannot describe the procedure for each possible combination. Yet, the home screen as a starting point has

turned out to be most convenient for the description.

Insert the Audio CD via slot [8] into Trinity. After a short time, the disk drive will start

up and import all CD information (TOC).

(A) Use key [4] or [5] to

navigate to the entry

Audioplayer and select with key

[2].

(B) Use key [4] or [5] to

navigate to the entry Music

Add-ons and select with key [2].

navigate to the entry Search by

sender and select with key [2].

(D) Use key [4] or [5] to choose

an entry from the list below and

select with key [2].

() Use key [4] or [5] to

navigate to the radio channel

which you would like to

playback and select with key

[2].

(F) The playback on the

selected radio channel will start

after a few seconds. You can

go back to the channel

overview by pressing key [5].

(Picture ).

3.4 Playback music from a connected device

Three analogue devices (input-1, input-2, input-3) and four digital sources (digital-1, digital-2,

digital-3, digital-4) can be connected to Trinity. Use key [4] and [5] to navigate on the

home screen to the input socket which you would like to playback.

(A) The CD is read. You can

cancel this process, if desired.

(B) Use key [4] or [5] to

navigate to the music title and

select with key [2].

back. Use key [1] or [3] to skip

forward and backward.

(D) To stop playback, press [5].

For the next title, press [3], for

the title before, press [1]. With

the key [2] the pause can be

called up.

(A) Select Inputsand confirm

with key [2] .

(B) Select the desired Input with

navigation Button [ 4 or 5].The

selected source will now be

played.

Inhaltsverzeichnis

Beliebte Medienplayer Handbücher anderer Marken

Visual Land

Visual Land Impulse Bedienungsanleitung

limHD

limHD 200i Bedienungsanleitung

Transcend

Transcend DMP10 Bedienungsanleitung

Philips

Philips GoGear Muse SA2MUS08 Bedienungsanleitung

Fantec

Fantec MM-HDRL Bedienungsanleitung

Dune HD

Dune HD Duo 4K Bedienungsanleitung

IAdea

IAdea HMP-505S Bedienungsanleitung

Camos

Camos MMS-1000 Bedienungsanleitung

Energy

Energy 75 Series Bedienungsanleitung

Z3 Technology

Z3 Technology DME-03 Bedienungsanleitung

Sony

Sony SVR-2000 Benutzerhandbuch

Meicheng

Meicheng HD-1080K12 Bedienungsanleitung

DENAFRIPS

DENAFRIPS ARCE Bedienungsanleitung

Topaz

Topaz CMS Media Player Gebrauchsanweisung

InFocus

InFocus LightCast Bedienungsanleitung

IconBiT

IconBiT XDS1003D Bedienungsanleitung

Quanmax

Quanmax QDSP-2090 Series Bedienungsanleitung

Samsung

Samsung MP-80S Bedienungsanleitung