Trinamic TMCM-1140 Bedienungsanleitung

Getting started TMCM-1140

TRINAMIC Motion Control GmbH & Co. KG

Hamburg, Germany

www.trinamic.com

STARTING UP

1. Choose your interface.

USB: connect USB interface to PC.

Download and install the file TMCM-

1140.inf (www.trinamic.com) after

connecting the power supply.

RS485 or CAN: use the interface

connector and connect an interface

converter.

Connect the chosen interface to PC.

2. Connect the 24V DC power supply.

3. Connect motor to 4-pin connector of the

module

4. Turn power ON. The green LED starts

flashing slowly and the motor is

powered but in standstill now. If this

does not occur, turn power OFF and

check your connections and power

supply!

5. Start the TMCM-IDE program.

See next page how to configure the

connection and to use the IDE.

6. Type in the open window:

ROL 0, 500 //Rotate motor 0 with speed 500

WAIT TICKS, 0, 500

MST 0

ROR 0, 250 //Rotate motor 0 with speed 250

WAIT TICKS, 0, 500

MST 0

7. Click the Assemble icon. Thereafter click the Download icon to download the code to the module.

Click the Run icon. The program will now be executed.

8. Click the Stop icon and start TMCL™Direct Mode to issue the following commands:

ROR rotate right, motor 0, value 500 -> click Execute / The motor is rotating now.

MST motor stop, motor 0-> click Execute / The motor stops now.

FIRST STEPS ARE MADE.

Please refer to the TMCM-1140 Hardware and Firmware Manuals, too.

YOU NEED

-TMCM-1140

-Stepper motor

-Serial interface: RS485, CAN, or USB

-If you choose RS485 or CAN: interface

converter suitable to your module

-Supply voltage +24V DC (9… 28V DC)

-TMCL-IDE program and PC

-Cables for interface, motor, and power

PRECAUTIONS

-Do not mix up connections or short-circuit pins.

-Avoid bounding I/O wires with motor power

wires.

-Do not exceed the maximum power supply of

+28V DC!

-Do not connect or disconnect the motor while

powered!

-START WITH POWER SUPPLY OFF!

In/Out

Interface

USB

Motor

USB

Serial USB

interface

Converter

e.g. USB-2-485

USB

RS485

CAN

Converter

e.g. USB-2-X

CAN

Pin 6 CAN_L

Pin 5 CAN_H

Pin 1 GND

RS485

Pin 4 RS485-

Pin 3 RS485+

Pin 1 GND

Power supply

Pin 2 9… 28V DC

Pin 1 GND

Note, that the

GND pin has to

be used for

power supply

and for the

interfaces also.

Motor

Pin 1 OB2

Pin 2 OB1

Pin 3 OA2

Pin 4 OA1

Getting started TMCM-1140

TRINAMIC Motion Control GmbH & Co. KG

Hamburg, Germany

www.trinamic.com

TMCL-IDE

The TMCL-IDE is available on www.trinamic.com.

6. Click Assemble first, then Download and

Run to start the program.

Assemble

Download Run StopDissemble Continue

7. Stop all running programs by clicking

Stop and start Direct Mode by clicking the

appropriate icon.

8. The TMCM-1140 is automatically detected,

if the communication is established.

9. Issue a command by choosing Instruction,

Type, Motor, and Value and click Execute

to send it to the module.

1. Make sure the COM port you intend to

use is not blocked by another program.

2. Open TMCL-IDE by clicking TMCL.exe.

3. Choose Setup and Options and

thereafter the Connection tab.

4. Choose COM port and Type. Click OK.

5. Write a program code into the editor

window and save it with File/Save.

Note, that TMCL programs run

standalone on the module, too.

TROUBLESHOOTING

IF COMMUNICATION IS NOT ESTABLISHED

-Check if the green LED lights up. If not, check

your power supply.

-Try to start Direct Mode and check, if the

module is detected automatically.

-Check, if you are using the right COM port and

it is not blocked by another program.

-Check, if the file TMCM-1140.inf is installed

correctly.

-Check your connection settings. Default: 9600

baud, address 1.

-Check if the RS485 or CAN converter functions.

IF MOTOR DOES NOT RESPOND

-Usually the communication is not established

(see above).

-Check the motor connection.

-If you are using a TMCL program try a

movement command in Direct Mode to check

if there is a problem with it.

-Restore factory settings by using instruction

137 for cancelling all settings modified by the

user.

Andere Handbücher für TMCM-1140

Andere Trinamic Controller Handbücher

Trinamic

Trinamic PD1-113-57-SE Bedienungsanleitung

Trinamic

Trinamic TMCM-351 Bedienungsanleitung

Trinamic

Trinamic TMCM-310 Bedienungsanleitung

Trinamic

Trinamic TMCM-1311 Gebrauchs- und Pflegehandbuch

Trinamic

Trinamic TMCM-1210 Bedienungsanleitung

Trinamic

Trinamic TMCM-1140 Bedienungsanleitung

Trinamic

Trinamic TMCM-1141 Bedienungsanleitung

Trinamic

Trinamic TMCM-610 Bedienungsanleitung

Trinamic

Trinamic TMCM-1141 Bedienungsanleitung

Trinamic

Trinamic IDX 4803 Bedienungsanleitung

Trinamic

Trinamic TMCL-LITE TMCM-1316 Bedienungsanleitung

Trinamic

Trinamic TMCM-013-42 Bedienungsanleitung

Trinamic

Trinamic TMCM-3110 Bedienungsanleitung

Trinamic

Trinamic TMCM-6110 Bedienungsanleitung

Trinamic

Trinamic TMCM-078 Bedienungsanleitung

Trinamic

Trinamic TMCM-110 Bedienungsanleitung

Trinamic

Trinamic TMCM-343 Bedienungsanleitung

Trinamic

Trinamic TMCM-342 Bedienungsanleitung

Trinamic

Trinamic TMCM-6110 Bedienungsanleitung

Trinamic

Trinamic TMCM-1260 Bedienungsanleitung

Trinamic

Trinamic PANdrive PD42-1-1370 Bedienungsanleitung

Trinamic

Trinamic SIXpack 2 Bedienungsanleitung

Trinamic

Trinamic TMC428 Montage- und Bedienungsanleitung

Trinamic

Trinamic TMCM-1310 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung