Trinamic TMC603-EVAL Bedienungsanleitung
EVALUATION FOR ICs EVALUATION BOARD
TRINAMIC Motion Control GmbH & Co. KG
Hamburg, Germany
TRAMS Getting Started
+ + TRAMS
+ +
TABLE OF CONTENTS
1Step 1: Software ........................................................................................................................................................... 2
2Step 2: Installation ...................................................................................................................................................... 2
3Step 3: Firmware upload ........................................................................................................................................... 2
4Step 5: Connect with the 3D printer..................................................................................................................... 3
5Step 6: Powering up ................................................................................................................................................... 5
6Step 7: Printing ............................................................................................................................................................. 5
7Life Support Policy....................................................................................................................................................... 6
8Revision History............................................................................................................................................................ 7
8.1 Firmware Revision .............................................................................. Fehler! Textmarke nicht definiert.
8.2 Document Revision ............................................................................................................................................. 7
9References ...................................................................................................... Fehler! Textmarke nicht definiert.
TRINAMIC Reprap Arduino Mega
Shield
Application specific Reference
Design for 3D-Printers with
TMC5130 Motor Controller /
Driver for Two Phase Stepper
Motors
Up to 4x 1.1A RMS/ +12V… 24V DC
SPI
2x Ref. Switch Input per Axis
TRAMS getting started / (Rev. 1.00 / 2015-OCT-26) 2
www.trinamic.com
1Step 1: Software
You will need the following software:
-The Arduino IDE (we used version 1.6.1)
-The TRAMS Firmware
-The Repetier-Host software (we used version 1.0.6)
2Step 2: Installation
Install the Arduino IDE and the Arduino USB driver as shown in the official Arduino guide Arduino
installation guide.
Install Repetier-Host.
3Step 3: Firmware upload
Connect the Arduino Mega without the TRAMS with the computer.
Open the “Marlin.ino” from the firmware folder with the Arduino IDE.
Select the Arduino Mega board and the correct USB port in the IDE and upload the firmware.
To test if the firmware was uploaded properly start Repetier-Host and press Strg+p.
Now choose your USB port and set the baud rate to 56000.
Click on “Connect”. You should now see a similar text in the lower log window:
TRAMS getting started / (Rev. 1.00 / 2015-OCT-26) 3
www.trinamic.com
4Step 5: Connect with the 3D printer
Unplug the Arduino from the USB port. It should not be connected to anything right now.
Put the TRAMS on the Arduino.
1. Make sure that the main power (VM) and the heat bed power (V_HEATBEAD) are NOT connected
to a power supply! You can damage the board if you connect/disconnect parts (e.g. motors)
while under power.
2. Connect the motors to the corresponding connector.
If you are using only one motor for the Z-Axis you need to connect pin 1 to 2 and
pin 3 to 4 at one of the connectors.
3. Connect the end stops for the X-, Y- and Z-Axis. The Extruder normally doesn’t need an end
stop.
IMPORTANT:
Right now, the firmware only supports using one end stop per axis which needs to be the left
one. Connect the end stops as shown here:
TRAMS getting started / (Rev. 1.00 / 2015-OCT-26) 4
www.trinamic.com
4. Connect the extruder thermistor to THERM_0 and the heatbed thermistor to THERM_1. (We used
100k thermistors for testing). If you don’t use a heatbed you still need to connect a 110k
“dummy” resistor to the THERM_1 port.
5. Connect the extruder heating cartridge to the EXT_0 connector.
6. If you have a controlled fan for cooling the printed filament you can connect it to the FAN
connector. Watch out for the right polarity.
7. If you have a fan or lights which needs to be powered all the time you can connect them to
the two VM ports:
8. If you have a heatbed connect it to the HEATBED port.
TRAMS getting started / (Rev. 1.00 / 2015-OCT-26) 5
www.trinamic.com
5Step 6: Powering up
1. Make sure that both fuses are working properly.
2. Connect VM to 12-24V.
3. If you have a heatbed you need to connect V_HEATBED to 12-24V, too.
4. Connect the Arduino with the computer.
6Step 7: Printing
Start Repetier-Host and click on “Connect”.
Click the homing button:
Your printer should now home.
You are now ready to print.
TRAMS getting started / (Rev. 1.00 / 2015-OCT-26) 6
www.trinamic.com
7Life Support Policy
TRINAMIC Motion Control GmbH & Co. KG does not
authorize or warrant any of its products for use in life
support systems, without the specific written consent of
TRINAMIC Motion Control GmbH & Co. KG.
Life support systems are equipment intended to support
or sustain life, and whose failure to perform, when
properly used in accordance with instructions provided,
can be reasonably expected to result in personal injury
or death.
© TRINAMIC Motion Control GmbH & Co. KG 2013
Information given in this data sheet is believed to be
accurate and reliable. However neither responsibility is
assumed for the consequences of its use nor for any
infringement of patents or other rights of third parties,
which may result from its use.
Specifications are subject to change without notice.
All trademarks used are property of their respective
owners.
TRAMS getting started / (Rev. 1.00 / 2015-OCT-26) 7
www.trinamic.com
8Revision History
8.1 Document Revision
Version
Date
Author
Description
1.00
2015-OCT-26
JP
Initial version
Table 8.1 Document revision
Andere Handbücher für TMC603-EVAL
3
Inhaltsverzeichnis
Andere Trinamic Hauptplatine Handbücher
Trinamic
Trinamic TMC5031-EVAL Bedienungsanleitung
Trinamic
Trinamic TMC603-EVAL Bedienungsanleitung
Trinamic
Trinamic TMCM-1617-BB Bedienungsanleitung
Trinamic
Trinamic TMC2300-IOT-REF Bedienungsanleitung
Trinamic
Trinamic TMC389-EVAL Bedienungsanleitung
Trinamic
Trinamic TMC6200-EVAL Bedienungsanleitung
Trinamic
Trinamic PD-1141 Bedienungsanleitung
Trinamic
Trinamic TMC2208-EVAL Bedienungsanleitung
Trinamic
Trinamic TMC5130-EVAL Bedienungsanleitung
Trinamic
Trinamic TMC332 Bedienungsanleitung
Trinamic
Trinamic TMC7300-EVAL Bedienungsanleitung
Trinamic
Trinamic TMC236 Bedienungsanleitung
Trinamic
Trinamic TMC8462-EVAL Bedienungsanleitung
Trinamic
Trinamic TMC2300-MOTOR-EVAL Bedienungsanleitung
Trinamic
Trinamic PANdrive PD-1161 Bedienungsanleitung
Trinamic
Trinamic TMC603-EVAL Bedienungsanleitung
Trinamic
Trinamic TMC262-EVAL Bedienungsanleitung
Trinamic
Trinamic TMCM-0960-MotionPy V21 Bedienungsanleitung
Trinamic
Trinamic TMC603-EVAL Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
