Triplett MM200 Bedienungsanleitung

User Manual

Model MM200

Compact Digital MultiMeter

Introduction

Congratulations on your purchase of the Triplett MM200 Compact Digital

Multimeter. The MM200 is a compact multimeter specially designed for home

and light electrical use. The compact structure makes it easy to hold in one

hand, and the EBTN screen allows users to obtain clear readings at maximum

angle. The multimeter meets the EN61010-1:2010, EN61010-2-030:2010, and

EN61326-1:2013 safety standards and is able to safely operate within the CAT

III 600V environment.

Features

Battery Power Indication on Power Up via LED

- Green (Normal State) Yellow (Low Battery) and Red (Very Low) 



Automatic AC/DC Voltage Measurement Detection



Non Contact ACV Detection with LED indicating electric field strength.



Full Feature Protection 



Safety

This symbol, adjacent to another symbol or terminal, indicates the user must

refer to the manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal use,

hazardous voltages may be present

Double insulation

•Improper use of this meter can cause damage, shock, injury or death. Read and understand

this user manual before operating the meter.

•Make sure any covers or battery doors are properly closed and secured.

•Always remove the test leads before replacing the battery or fuses.

•Inspect the condition of the test leads and the meter itself for any damage before

operating the meter. Repair any damage before use.

•Do not exceed the maximum rated input limits.

•Use great care when making measurements if the voltages are greater than 25VAC

rms or 35VDC. These voltages are considered a shock hazard.

•Always discharge capacitors and remove power from the device under test before

performing Diode, Resistance or Continuity tests.

•Remove the battery from the meter if the meter is to be stored for long periods.

•To avoid electric shock, do not measure AC current on any circuit whose voltage

exceeds 250V AC.

Safety standards

Design standards

EN61010-1: 2010;

EN61010-2-030:2010;

EN 61326-1:2013

EN61010-2-033:2012,EN61326-2-2:2013

EMC

RF field (1V/m): Overall accuracy = specified accuracy ±5% of range

RF field (>1V/m): No specified

calculation

Measurement

standards

CAT

III 600V,

double insulation and

material pollution degree II

Dimensions

130mm×65mm×28mm

Weight

About 130g (including batteries)

Operating Instructions

AC/DC Voltage Measurements

1. Insert the black test lead banana plug into the negative COM

jack and the red test lead banana plug into the positive V

jack.

2. Turn the rotary switch to the Vposition.

3. Press the SELECT button to select either AC or DC.

4. Touch the test probes to the circuit under test and read the

voltage on the display.

**NOTE: The

meter

has

the function

ACV/DCV

automatic

identification (voltage

≥

0.5V).

If you

want

to measure

voltage

less

than

0.5V,

press the

SELECT

button

toggle

the

AC and

voltage to lock the measurement

mode;

After pressing

the

SELECT

button, the meter no longer has the function

ACV

/DCV

automatic

identification,

unless you turn

the

range switch or restart the meter!**

Resistance Measurements

1. Insert the black test lead banana plug into the negative COM jack and the red test lead

banana plug into the positive Ωjack.

2. Set the function switch to the Ωposition.

3. Touch the test probe tips across the circuit or part under test. It is best to disconnect one

side of the part under test so the rest of the circuit will not interfere with the resistance

reading.

4. Read the resistance in the display.

Continuity Measurements

1. Insert the black test lead banana plug into the negative COM jack and the red test lead

banana plug into the positive V/Ω/mA jack. Observe polarity.

2. Turn the rotary switch to the •))) position.

3. Touch the test probes to the circuit or device under test. If the resistance is less

than approximately 30Ω the buzzer will sound.

**NOTE: Before making Continuity Measurements make sure circuit power is OFF

and fully discharge any Capacitors to avoid damage to the meter.

Temperature Measurements

WARNING: To avoid electric shock, disconnect test

leads from any source of voltage before making a

temperature measurement. Be sure that the

thermocouple has been removed before changing to any

other measurement function.

1. Insert the type K thermocouple probe into the Temp

and COM jacks.

2. Turn the rotary switch to the oC/ oFposition. Default is

oC, Press Select to change to oF if desired.

3. Read the temperature on the display.

Non-Contact Voltage and AC Field Sensing

1) Turn the rotary switch to the NCV position.

Bring

the

front end of

the

meter close to the object to

be measured.

**Note: The intensity of the electric field sensing is

indicated by the

LED indicator and the segment "-" on the LCD. The

more segments (up to four segments )are displayed,

the higher the electric field intensity is and the

faster it beeps. **

Data Hold

Press the Hold button to freeze the reading in the display. “H” will appear in the LCD.

Press the key again to release the display.

Low Battery

If the + - low battery icon appears in the display, replace the batteries to maintain proper

operation.

Auto-Ranging

The meter will auto range to the optimum range to provide the best resolution and

accuracy for the input signal.

Auto Power Off

1. This meter will automatically shut off after approximately 15 minutes of operation. If the meter

shuts off, rotate the function switch to OFF and on again (or press the HOLD button) to resume

operation.

2. To disable the auto power off, hold the SELECT button while turning power on or press

the SELECT button after auto power off has turned the meter off.

Specifications

Maintenance

Warning: To avoid electric shock, do not operate your meter until the battery cover is in

place and fastened securely.

1.Keep the meter dry.

2.Use and store the meter in mild ambient conditions. Temperature extremes can shorten

the life of the electronic parts and distort or melt plastic parts.

3.Handle the meter gently. Dropping it can damage the electronic parts or the case.

4.Keep the meter clean. Wipe the case occasionally with a damp cloth. DO NOT use

chemicals, cleaning solvents or detergents.

5.Use only fresh batteries of the recommended size and type. Remove old or weak batteries so

they do not leak and damage the unit.

6.If the meter is to be stored for a long period of time, the batteries should be

removed to prevent damage to the unit.

Battery Replacement

1. Replace the batteries immediately when the low battery

symbol “ ”appears on the LCD, otherwise the

measurement accuracy might be affected. Battery

specification: AAA battery 1.5V×2

2. Battery replacement: Use a screwdriver to unscrew the

screw on the battery cover (top), and remove the cover

to replace the batteries. Pay attention to the positive and

negative polarity when installing the new batteries.

Warranty Information

Triplett / Jewell Instruments extends the following warranty to the original

purchaser of these goods for use. Triplett warrants to the original purchaser for

use that the products sold by it will be free from defects in workmanship and

material for a period of (1) one year from the date of purchase. This warranty

does not apply to any of our products which have been repaired or altered by

unauthorized persons in any way or purchased from unauthorized distributors

so as, in our sole judgment, to injure their stability or reliability, or which have

been subject to misuse, abuse, misapplication, negligence, accident or which

have had the serial numbers altered, defaced, or removed. Accessories,

including batteries are not covered by this warranty

Inhaltsverzeichnis

Andere Triplett Multimeter Handbücher

Triplett

Triplett 9007 Bedienungsanleitung

Triplett

Triplett 9005-A Bedienungsanleitung

Triplett

Triplett 1301 Bedienungsanleitung

Triplett

Triplett CM24 Bedienungsanleitung

Triplett

Triplett 9055 Bedienungsanleitung

Triplett

Triplett MM300 Bedienungsanleitung

Triplett

Triplett 310-TEL 4 Bedienungsanleitung

Triplett

Triplett MM200-NIST Bedienungsanleitung

Triplett

Triplett 630 Type 5 Bedienungsanleitung

Triplett

Triplett 3303 Bedienungsanleitung

Triplett

Triplett MM525 Bedienungsanleitung

Triplett

Triplett 2103 Bedienungsanleitung

Triplett

Triplett 9045 Bedienungsanleitung

Triplett

Triplett MM350 Bedienungsanleitung

Triplett

Triplett 1101-NIST Bedienungsanleitung

Triplett

Triplett 1101-B Bedienungsanleitung

Triplett

Triplett MM650 Bedienungsanleitung

Triplett

Triplett 1401 Bedienungsanleitung

Triplett

Triplett 1101-B Bedienungsanleitung

Triplett

Triplett 2202 Bedienungsanleitung

Triplett

Triplett MM650 Bedienungsanleitung

Triplett

Triplett 1101-A Bedienungsanleitung

Triplett

Triplett 9065 Bedienungsanleitung

Triplett

Triplett 9015-A Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung