Triplett FM260 Bedienungsanleitung

User Manual

FM260

Formaldehyde (HCHO or CH20) and Total

Volatile Organic Compounds (TVOC) Tester

Introduction

Thank you for selecting the Triplett FM260. The FM260 measures

HCHO (formaldehyde) and TVOC (Total Volatile Organic

Compounds).



www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Potential sources for TVOCs include paints, finishes, adhesives, cigarette

smoke, pesticides, personal care products, car exhaust, new furnishings,

wall coverings, household cleansers, and cooking fuels. Chemicals

include: Acetone, Ethylene Glycol, Formaldehyde, Xylene, 1,3‐butadiene,

Tetrachloroethene, Hydrogen Sulfide, Ammonia, Toluene, Benzene,

Methylene Chloride, Perchloroethylene, and MTBE.

Features

Fuel Cell Formaldehyde Sensor Technology

High accuracy measurements

Backlit LCD display

Real‐time display of HCHO (formaldehyde) concentration in air

Real‐time display of TVOC (Total Volatile Organic Compounds) concen

tration in air

Two unit selections (PPM, mg/m³)

Audio‐visual High and Low Alarms for HCHO

Auto power off

Description

METER DESCRIPTION

1. HCHO sensor (front)

2. AC Adaptor jack (under flap)

3. Down arrow and Alarm Setup button

4. Battery compartment (rear)

5. ON‐OFF button (also used in Alarm Setup)

6. Up arrow and UNIT selection button

7. Backlit Display

8. TVOC sensor (rear)

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Operation

POWER THE METER

Press the button to turn on the meter. The battery symbol informs the

user as to the battery strength. Connect the battery charger to recharge

the battery. Long press the button to power off. The LCD will count

down: 3, 2, 1, then OFF before switching off.

AUTO POWER OFF

Themeter will switch off after 30 minutes of inactivity. Press any function

button to prevent the meter from powering off; the auto power off timer

will be then be reset. The APO display symbol reminds the user that Auto

Power OFF is always active.

GENERAL USE

All LCD display lines will switch ON when power is applied to the

meter. The bottom TVOC display will count down from 10 seconds

or from 90 seconds (depending on the environment) to zero. When

countdown is complete the meter is ready for use.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

In normal mode, the top display indicates the HCHO concentration

in PPM or mg/m³. The bottom display indicates the TVOC

concentration in PPM or mg/m³.

Use the UNIT button to switch units between PPM and mg/m³.

With the meter on, if the measured HCHO concentration exceeds

the high or low user‐ programmable Alarm thresholds, the LED

display will flash red in color and the audible beeper will sound

(unless it has been disabled with the SET/▼button). Press SET/▼

to silence the alarm beeper (when it is sounding) or to disable the

beeper entirely. When disabled, the displayed beeper symbol is

switched off.

ALARM SETUP (HCHO only)

Low Alarm Setup

1. Long press the SET/▼button to enter the setup mode.

2. The low alarm icon will display and the LCD will show the low

alarm threshold.

3. Use the ▲and ▼buttons to adjust the low alarm threshold.

4. Press the button to go to the high alarm setup screen.

High Alarm Setup

1. Use the ▲and ▼buttons to adjust the high alarm threshold.

2. Press the button to return to the normal measurement mode.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

CONTROL BUTTONS

1. Short press the ▼SET button to silence the beeper (when it is

sounding) or to disable/enable the alarm beeper. This button is

also used as a down arrow to change the high and low Alarm

threshold values in the Alarm Setup mode.

2. Long press the ▼SET button to enter the Alarm Setup Mode (See

Alarm Setup section).

3. Short press the ▲UNIT button to change the unit of measure

(PPM or mg/m³) or to use it as an up arrow to set the alarm

threshold values in the Alarm Setup mode.

SAFETY

Do not store or use the instrument in an environment

where corrosive gas is present. Do not obstruct the sensors

when in use.

Use only the supplied lithium‐ion battery to power the meter.

Use only the supplied AC adapter/battery charger to charge the lithium‐

ion battery.

BATTERY CHARGE and REPLACEMENT

1. When the battery requires charging, plug the supplied battery

charger into the meter (left side, under flap) and to a source of

AC power. A full charge requires 2 hours.

2. To replace the battery, open the rear battery compartment and

replace the Polymer lithium‐ion battery (7.4V 1300mAh). Re‐

assemble the meter before use.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Battery Safety Notes: Please dispose of batteries responsibly; never

dispose of batteries in a fire, batteries may explode or leak. If the meter

is not to be used for 60 days or more, remove the battery and store

separately.

Never dispose of used batteries or rechargeable batteries in

household waste.

As consumers, users are legally required to take used batteries

to appropriate collection sites, the retail store where the

batteries were purchased, or wherever batteries are sold.

Disposal: Do not dispose of this instrument in household waste. The user is

obligated to take end‐of‐ life devices to a designated collection point for

the disposal of electrical and electronic equipment.

CLEANING AND STORAGE

Periodically wipe the case with a damp cloth and mild detergent; do

not use abrasives or solvents. Please remove the battery if the meter

is stored for a long period of time.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Specifications

Sensor

Professional Fuel Cell technology

HCHO Range

0.00 to 5.00 mg/m³ (or PPM)

HCHO Resolution

0.01 mg/m3 (or PPM)

HCHO Basic

Accuracy

±5% FS

TVOC Range

0.00 to 9.99 mg/m³ (or PPM)

TVOC Resolution

0.01 mg/m³ (or PPM)

TVOC Basic

Accuracy

±5% FS

Response Time

≤ 2 seconds

Operating

Temperature

0°C to 40°C (32 to 104°F)

Storage

Temperature

‐10°C to 60°C (14 to 140°F)

Power Supply

Rechargeable Polymer lithium‐ion battery

(7.4V 1300mAh)

Battery Charge

Time

Approx. 3 hours with AC adapter

Battery

7.4V 1300mAh (part # VPC‐BATT)

Dimensions

165 x 60 x 25mm (6.5 x 2.4 x 1.0 in.)

Weight

584g (20.6 oz.)

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Warranty

Triplett / Jewell Instruments extends the following warranty to the original purchaser of

these goods for use. Triplett warrants to the original purchaser for use that the products

sold by it will be free from defects in workmanship and material for a period of (1) one

year from the date of purchase. This warranty does not apply to any of our products

which have been repaired or altered by unauthorized persons in any way or purchased

from unauthorized distributors so as, in our sole judgment, to injure their stability or

reliability, or which have been subject to misuse, abuse, misapplication, negligence,

accident or which have had the serial numbers altered, defaced, or removed.

Accessories, including batteries are not covered by this warranty

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Inhaltsverzeichnis

Andere Triplett Prüfgeräte Handbücher

Triplett

Triplett BQ-600A Bedienungsanleitung

Triplett

Triplett CamView IP Pro-X Series Bedienungsanleitung

Triplett

Triplett 310 Bedienungsanleitung

Triplett

Triplett USB-Bug Bedienungsanleitung

Triplett

Triplett TVR10G PRO Bedienungsanleitung

Triplett

Triplett TLT10 Bedienungsanleitung

Triplett

Triplett CTX1200 Bedienungsanleitung

Triplett

Triplett 2000 Bedienungsanleitung

Triplett

Triplett POE2000 Pro Bedienungsanleitung

Triplett

Triplett ET550 Bedienungsanleitung

Triplett

Triplett CTT42 Bedienungsanleitung

Triplett

Triplett WireMaster Coax Bedienungsanleitung

Triplett

Triplett 310-TEL Bedienungsanleitung

Triplett

Triplett EMF20 Bedienungsanleitung

Triplett

Triplett 8150-BR-KIT Bedienungsanleitung

Triplett

Triplett 9310-A Bedienungsanleitung

Triplett

Triplett WireMaster Mapper Bedienungsanleitung

Triplett

Triplett PR450 Bedienungsanleitung

Triplett

Triplett CamView HD Pro Bedienungsanleitung

Triplett

Triplett WireMAster Coax BNC Bedienungsanleitung

Triplett

Triplett TLT10 Bedienungsanleitung

Triplett

Triplett MG430 Bedienungsanleitung

Triplett

Triplett CTT47 Bedienungsanleitung

Triplett

Triplett Fox Jr. Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung