Tripp Lite PDU3VSR6H50A Bedienungsanleitung

Owner’s Manual

3-Phase Switched 0U Power

Distribution Units

208V MODELS

PDU3VSR6H50A • PDU3VSR6G60A

(Series Number: AG-0065) • (Series Number: AG-0063)

400V MODELS

PDU3XVSRHWA • PDU3XVSRHWB PDU3XVSR6G32A • PDU3XVSR6G32B

(Series Number: AG-0057) (Series Number: AG-0080)

PDU3XVSR6L2230 • PDU3XVSR6L2230B PDU3XVSR6G60A • PDU3XVSR6G60B

(Series Number: AG-0056) (Series Number: AG-0093)

PDU3XVSR6G30A • PDU3XVSR6G30B PDU3XVSR6G63A • PDU3XVSR6G63B

(Series Number: AG-0096) (Series Number: AG-0094)

Important Safety Instructions 2

Installation 3

Digital Display 8

Using the Digital Display 10

Features 16

Conﬁguration and Operation 18

Service 18

Warranty and Warranty Registration 19

Español 20

Français 39

Русский 58

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an ISOBAR6ULTRA

surge protector—a $100 value!

www.tripplite.com/warranty

18-12-188-9332B8.indb 1 12/20/2018 5:19:13 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during

the installation, operation, and storage of this product. Failure to heed these

instructions and warnings may affect the product warranty.

• The PDU provides convenient multiple outlets, but it DOES NOT provide surge or line noise

protection for connected equipment.

• The PDU is designed for indoor use only in a controlled environment away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• The power requirement for each piece of equipment connected to the PDU must not exceed

the individual outlet’s load rating.

• The total power requirement for equipment connected to the PDU must not exceed the

maximum load rating for the PDU.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to modify the PDU, including the input plugs and power cables.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to signiﬁcantly

affect its safety or effectiveness is not recommended. Do not use this equipment in the

presence of a ﬂammable anesthetic mixture with air, oxygen or nitrous oxide.

• Never attempt to install electrical equipment during a thunderstorm.

• Keep indoor ambient temperature between 32°F and 104°F (0°C and 40°C).

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• Do not attempt to open the PDU; there are no user-serviceable parts inside.

• The PDU must be installed by a qualiﬁed technician only.

18-12-188-9332B8.indb 2 12/20/2018 5:19:13 PM

1-1 1-2

1-4

1-3

1-5

Installation

Mounting the PDU

Note: The illustrations may differ somewhat from your PDU model. Regardless of conﬁguration, the user must

determine the ﬁtness of hardware and procedures before mounting. The PDU and included hardware are designed

for common rack and rack enclosure types and may not be appropriate for all applications. Exact mounting

conﬁgurations may vary. Screws for attaching the mounting brackets to the PDU are included. Use only the screws

supplied by the manufacturer or their exact equivalent.

Note: Mounting buttons come preinstalled to the PDU for toolless mounting.

1-1 To attach the mounting brackets to the

PDU, remove the mounting buttons.

1-2 Attach the mounting brackets to the

PDU with the included screws.

1-3 Attach the PDU to a vertical rail in

your rack or rack enclosure. (Use the

mounting hardware that came with your

rack or rack enclosure to attach the

mounting brackets to the rail.)

1-4 To reinstall the mounting buttons for

toolless mounting, remove the mounting

brackets then install the mounting

buttons onto the PDU. Position the PDU

as desired in the rack enclosure, align

the buttons with the rack mounting

slots, and slide the PDU into position.

Note: Be sure to insert the 2 buttons into either

the upper hole at each end of the PDU or into

the lower hole at each end of the PDU.

1-5 To install the PDU with its outlets facing

the rear of the rack, use the included

PDUMVROTATEBRKT accessory. First,

attach the mounting button Ato the

V-shaped bracket Busing the included

screw and washer. Then, use the

button-mount slot to attach the bracket

to the PDU and the mounting button to

attach the PDU to the rack. The bracket

effectively repositions the mounting

brackets allowing for the PDU outlets to

face the rear of the rack.

18-12-188-9332B8.indb 3 12/20/2018 5:19:14 PM

Installation

Connecting the PDU

2-1 Each 208V model is equipped with 1 of 2 different input plugs.

60A Blue IEC

309 3P+E

Model Name Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Output

Voltage Breakers

Cord

Length

Outlets

PDU3VSR6G60A 60A Blue IEC

309 3P+E 45A 208V 208V 6 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m) 18 Total; 6 Banks of

(2) C19 and (1) C13

PDU3VSR6H50A HUBBLE

CS8365C 40A 208V 208V 6 x Double

Pole, 20A

Branch-Rated

6 ft.

(1.8 m) 18 Total; 6 Banks of

(2) C19 and (1) C13

HUBBLE

CS8365C

18-12-188-9332B8.indb 4 12/20/2018 5:19:14 PM

Installation

Each 400V model is equipped with 1 of 3 different input plugs.

63A Red IEC 309

3P+N+E

L22-30P 32A Red IEC 309

3P+N+E

Model Name Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Output

Voltage Breakers

Cord

Length

Outlets

PDU3XVSR6L2230

L22-30P 24A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6L2230B 30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSR6G30A 30/32A Red

IEC 309

3P+N+E 24A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6G30B 30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSR6G32A 30/32A Red

IEC 309

3P+N+E 32A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6G32B 30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSR6G60A 60/63A Red

IEC 309

3P+N+E 35A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6G60B 30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSR6G63A 60/63A Red

IEC 309

3P+N+E 40A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

6 ft.

(1.8 m)

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSR6G63B 30 Total; 6 Banks of

(1) C19 and (4) C13

PDU3XVSRHWA

N/A 40A 400V 230V

6 x Single

Pole, 20A

Branch-

Rated

N/A

24 Total; 6 Banks of

(2) C19 and (2) C13

PDU3XVSRHWB 30 Total; 6 Banks of

(1) C19 and (4) C13

18-12-188-9332B8.indb 5 12/20/2018 5:19:14 PM

4LOAD L2

BANK 1

1211

LOAD L1

BANK 2

LOAD L3

BANK 1

LOAD L2

BANK 1

STATUS

LINK

RESET

ENVIROSENSE

CONFIG

2-2

2-3

2-4

2-5

A B

Installation

2-2 Connect the input plug to your facility’s

compatible AC power source.

2-3 Connect your equipment’s input plugs to

the appropriate outlets on the PDU. The

LED near each outlet illuminates when

the outlet is ready to distribute live

AC power.

Note: It is recommended that you do not

connect a live load to the PDU. If the load you

intend to connect has an ON/OFF switch, please

turn the switch to OFF prior to connection.

2-4 Optional Cord Retention Procedure

Option 1 (Select Models): Use

the bridge lances located near each

receptacle to retain power cords. Tie

each equipment power cord to a bridge

lance by looping the cord and securing

it with one of the included cable ties A.

Make sure each cord can be unplugged

from the PDU without removing the

cable tie.

Option 2: Use the included C14 and

C20 plastic sleeves to secure plugs to

receptacles. Attach the sleeve to the

plug, making sure that the pull tabs B

remain outside the plug and that the ﬁt

is secure. To unplug equipment properly,

use the pull tabs to remove the plug

and sleeve from the receptacle.

For Installation

Purposes Only

Hardwire Installations

(PDU3XVSRHWA & PDU3XVSRHWB models only)

2-5 These models do not come equipped

with an input cable. Conduit and

adapters are installed to the endplate A,

wires are channeled through the conduit

and adapters to the terminal block,

located behind the access plate B.

WARNING

Only qualiﬁed personnel should perform hardwire installations. Wire codes and

requirements differ from area to area. Be sure to conform to local electrical

requirements.

18-12-188-9332B8.indb 6 12/20/2018 5:19:16 PM

2-6

Remove Access Plate Screws

Installation

Networking the PDU

Your PDU can receive IP address assignments via DHCP server (dynamic) or static (manual)

addressing methods. See the SNMPWEBCARD installation guide on the included CD or visit

www.tripplite.com/manuals. If you are uncertain which method to use, contact your network

administrator for assistance before continuing the conﬁguration process.

Note: The MAC address of the PDU (12-digit string in this format: 000667xxxxxx) is printed on a label attached

to the PDU enclosure. For static IP address assignments, use the RJ-45 to DB9 conﬁguration cable (part

number 73-1243) included with the PDU.

2-6 To access the terminal block to make

input wire connections, remove the

access plate located on the back side of

the PDU.

Ground Terminal

18-12-188-9332B8.indb 7 12/20/2018 5:19:16 PM

BC DE

Digital Display

A3-Digit Display: Shows measured or calculated values such as Amperage, Kilowatts,

Voltage, Power Unbalance Percentage, Temperature and Humidity.

BArrow Buttons: Scroll through indicated Outlet, Input, Bank, Power, Load Balance, Sensor

and Display Brightness options using these buttons. A long press of the up or down arrow

buttons allows the user to skip to the next sequential measurement category.

CMode Button: When a menu option is selected using the Arrow Buttons, the Mode Button

scrolls through the sub-options within each category. Sub-options are shown by the

Indicator LEDs.

DIndicator LEDs: Lit LED indicates which value is being displayed on the 3-digit screen.

Amps (A): When selected, the load on the selected Input Phase (L#), Load Bank (B#)

or Outlet (##) is displayed in amps.

Wattage (kW): When selected, the load on the selected Load Bank (B#), Outlet (##)

or Total Output Power (OP) is displayed in kW.

Voltage (V): Input Phase (L#), Load Bank (B#) or Outlet (##) voltage is displayed.

Unbalanced Load (%UB): When lit, the display shows the unbalanced load

percentage deviance from the average measured value. The percentage for the phase

with the highest deviance is displayed.

Temperature (T): If Tripp Lite ENVIROSENSE is connected, the ambient temperature

will be displayed when this option is selected. The temperature is displayed in Celsius

by default, but can be switched to Fahrenheit.

Relative Humidity (%RH): If Tripp Lite ENVIROSENSE is connected, the relative

humidity percentage will be displayed when this option is selected.

E2-Digit Display: This display indicates which Input Phase (L#), Load Balance (UB), Load

Bank (B#), Output Power (OP), Outlet (##) or Sensor (S#) option is selected.

18-12-188-9332B8.indb 8 12/20/2018 5:19:17 PM

4LOAD L2

BANK 1

LOAD L1

BANK 1 3

LOAD L1

BANK 1

1211

10 LOAD L1

BANK 2

LOAD L3

BANK 1 9

LOAD L1

BANK 2

LOAD L3

BANK 1

LOAD L2

BANK 1

STATUS

LINK

RESET

ENVIROSENSE

1817

16 LOAD L3

BANK 2

LOAD L2

BANK 2 15

1413

LOAD L3

BANK 2

LOAD L2

BANK 2

CONFIG

STATUS

LINK

RESET

ENVIROSENSE

CONFIG

B1 B3 B5

B2 B4 B6

Digital Display

Load Bank Receptacle Location

Display References for 208V Models

LOAD BANKS REFERENCE

SILKSCREEN LABEL DESCRIPTION 2-DIGIT DISPLAY REFERENCE

L1-L2, BANK 1 B1

L2-L3, BANK 2 B2

L3-L1, BANK 3 B3

L1-L2, BANK 4 B4

L2-L3, BANK 5 B5

L3-L1, BANK 6 B6

INPUT PHASE REFERENCE

INPUT PHASE REPORTED 2-DIGIT DISPLAY REFERENCE

INPUT PHASE L1 – L2 L1

INPUT PHASE L2 – L3 L2

INPUT PHASE L3 – L1 L3

Button Response Deﬁnitions:

Conﬁguration1Switch Action Control Function

Standard

Up Pushbutton

Depress ½ sec Sequentially, moves up one selection in

the menu.

Depress 3 sec Advances up to the next measurement

category.

Down Pushbutton

Depress ½ sec Sequentially, moves down one selection in

the menu.

Depress 3 sec Advances down to the next measurement

category.

Mode Pushbutton

Depress ½ sec Displays available options for a given

measurement category.

Depress 3 sec Selects the chosen available option for a given

conﬁguration category.

Alternate

Up Pushbutton

Depress ½ sec Sequentially, moves down one selection in

the menu.

Depress 3 sec Advances down to the next measurement

category.

Down Pushbutton

Depress ½ sec Sequentially, moves up one selection in the

menu.

Depress 3 sec Advances up to the next measurement

category.

Mode Pushbutton

Depress ½ sec Displays available options for a given

measurement category.

Depress 3 sec Selects the chosen available option for a given

conﬁguration category.

1Conﬁgured via Conﬁguration Category item “Outlet Indicator LED Color Code Options”.

18-12-188-9332B8.indb 9 12/20/2018 5:19:17 PM

i 5.5

L i

2 0 8

L i

i 5.5

2 0 8

i 5.5

2 0 8

Using the Digital Display

Scrolling Through Input Phases and Options

(Measurement Category)

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below. Note: Three dashes will be shown in the

3-digit display when the input phase voltage is unknown, due to abnormal tripped breaker

conditions.

Input Phase 1

Input Phase 2

Input Phase 3

Amps

Volts

To Unbalanced Load Detect

18-12-188-9332B8.indb 10 12/20/2018 5:19:17 PM

Andere Handbücher für PDU3VSR6H50A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Tripp Lite Stromverteilungseinheit Handbücher

Tripp Lite

Tripp Lite PDU3V602D354 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV20HVNET2 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUH20HVL6 Betriebsanleitung

Tripp Lite

Tripp Lite PDUNV Bedienungsanleitung

Tripp Lite

Tripp Lite Metered Rack PDU Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3VSR10L1530 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV30NET Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV30-ISO Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15HVAT Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3XMV6G32 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15ATNET Bedienungsanleitung

Tripp Lite

Tripp Lite SUDC208V42P60M Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3VN3L2120 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMVR30NET (AG-0045) Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3EVN3L2130 Bedienungsanleitung

Tripp Lite

Tripp Lite PDU1230 Bedienungsanleitung

Tripp Lite

Tripp Lite PSC240410USBB Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SUPDMB20KHW Bedienungsanleitung

Tripp Lite

Tripp Lite Metered Rack PDU Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3VN10L2120LV Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH20HVNET Bedienungsanleitung

Tripp Lite

Tripp Lite SUDC Series Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3MV6L2120B Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3VN10L2120 Bedienungsanleitung

Beliebte Stromverteilungseinheit Handbücher anderer Marken

hager

hager SP 015 Bedienungsanleitung

Pakedge

Pakedge PowerPak 9 Bedienungsanleitung

Pts

Pts 9042 Series Bedienungsanleitung

Shure

Shure WA405 Bedienungsanleitung

CORNING

CORNING CCH 4U Bedienungsanleitung

Panamax

Panamax M4LT-EX Bedienungsanleitung

PANCONNECT

PANCONNECT FLAT 3M Bedienungsanleitung

Raytheon

Raytheon 138-118 Bedienungsanleitung

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Bedienungsanleitung

Botex

Botex PSA 322-6 DL Bedienungsanleitung

GE QuiXtra 4000 Kurzanleitung

RDL

RDL EZ Series Bedienungsanleitung

StarTech.com

StarTech.com RKPW161915 Systemhandbuch

Vertiv

Vertiv Knürr DI-Strip Rack PDU Bedienungsanleitung

ABB

ABB PSBS0065 Handbuch

Baumuller

Baumuller BFN 3-1-0007-001 Handbuch

Eaton

Eaton StructuredWiringSolutions ESWT41600 Handbuch

GE GEK-45404F Bedienungsanleitung