Tripp Lite PDUMH15-ISO Bedienungsanleitung

Metered Rack PDU with

isobar®Surge Protection

PDUMH15-ISO

(Series Number: AGIB7403) PDUMH20-ISO

(Series Number: AGIB7410)

Important Safety Instructions 2

Important Warnings 2

Installation 3

Features 4

Warranty & Product Registration 6

Español 7

Français 13

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

14-08-270-9333B9.indb 1 9/15/2014 4:09:40 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed

during the installation, operation and storage of this product. Failure to

heed these instructions and warnings will void the product warranty.

Important Warnings

• The PDU provides surge and line noise protection to connected equipment through its outlets.

• The PDU is designed for indoor use only, in a controlled environment, away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• The PDU must be installed by a qualified technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the PDU should not draw more current than the individual

PDU’s outlet’s rating.

• The total load connected to the PDU must not exceed the maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to significantly

affect its safety or effectiveness is not recommended. Do not use this equipment in the

presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.

14-08-270-9333B9.indb 2 9/15/2014 4:09:41 PM

Installation

Note: The illustrations may differ somewhat from your PDU model.

1-1

1-3

1-2

1-4

1Determine Installation Configuration.

The PDU supports four primary installation

configurations: 1U Rack, 0U Rack, Wall

and Under-Counter. Choose a

configuration and follow the installation

instructions in the appropriate section of

Step 1 before proceeding to Step 2.

Note: Regardless of installation

configuration, the user must determine

the fitness of hardware and procedures

before mounting. The PDU and included

hardware are designed for common rack

and rack enclosure types and may not be

appropriate for all applications. Exact

mounting configurations may vary.

1-1 1U Rack Installation. Attach the PDU to

the rack by inserting four user-supplied

screws (A) through the PDU mounting

brackets (B) and into the mounting holes

of the rack rail as shown.

1-2 0U Rack Installation. Part 1: Remove

the screws (C) attaching the mounting

brackets to the PDU, change the

orientation of the brackets as shown and

reattach the brackets. Use only the screws

supplied by the manufacturer or their

exact equivalent (#6-32, 1/4” flat head).

Part 2: Attach the PDU vertically by

inserting two or more user-supplied screws

(A) through the PDU mounting brackets

(B) and into mounting points in the rack

or rack enclosure.

1-3 Wall Installation. After repeating Part 1

above, attach the PDU to a stable

mounting surface by inserting two or more

user-supplied screws (A) through the PDU

mounting brackets (B) and into secure

mounting points on the mounting surface.

1-4 Under-Counter Installation. After

repeating Part 1 above, attach the PDU to

a stable mounting surface by inserting four

user-supplied screws (A) through the PDU

mounting brackets (B) and into secure

mounting points on the mounting surface.

14-08-270-9333B9.indb 3 9/15/2014 4:09:42 PM

Ammeter: The total electrical current used by the PDU will be

displayed on the digital meter in amperes.

Input Plug (Varies by Model)

Outlets (Vary by Model): During normal

operation, the outlets distribute AC power

to connected equipment.

Circuit Breaker: If the current drawn by the equipment connected

to the PDU exceeds the Maximum Current Rating, the circuit

breaker will trip to prevent possible damage. When a circuit breaker

trips, its plunger will pop up. Disconnect excess equipment and

allow the breaker to cool at least one minute before depressing the

plunger to reset the breaker.

Features

NEMA 5-15P NEMA L5-20P

NEMA 5-15R NEMA 5-15/20R

Installation

2Attach the input plug of the PDU to a

grounded outlet. Insert the plug directly

into a grounded outlet that does not share

a circuit with a heavy electrical load (such

as an air conditioner or refrigerator).

Note: Select models include an input plug

adapter that converts the twist-lock input

plug to a straight-blade input plug. Attach

the input plug adapter to the input plug if

you wish to plug the PDU into a

compatible straight-blade outlet.

3Attach equipment to the PDU. Do not

exceed the load rating of the PDU. The

total electrical current used by the PDU

will be displayed on the digital meter in

amperes.

14-08-270-9333B9.indb 4 9/15/2014 4:09:43 PM

Features

NEMA 5-20P

NEMA L5-20R

Grounding Lug: Use this screw to connect the PDU to ground.

Input Plug Adapter (Select Models): Converts the twist-lock input

plug to a straight-blade input plug.

Diagnostic Indicator Lights: The three

LEDs on the front panel show current power

conditions (from left to right):

PROTECTION

PRESENT FAULT

LINE

Protection Present (Green LED): Indicates the surge-suppression components are intact and

providing full protection against spikes and surges. This LED should be lit anytime the PDU is

plugged in and power is present. If the Protection Present LED does not light, then some of the

surge suppression components are not functioning and the unit should be returned for repair

as soon as possible. You may still use the unit; however, connected equipment will be

protected from spikes and surges at a lesser level than normal.

Line Fault (Red LED)*: Indicates a wiring fault has been detected. If this LED illuminates at

any time while the unit is plugged in, the fault should be repaired by a qualified electrician as

soon as possible. This LED indicates that phases are reversed, ground is missing or some other

sort of wiring error exists in the circuit the PDU is plugged into. The Line Fault detector circuitry

will identify most common wiring faults, but will not necessarily detect every possible type of

fault.

Line “OK” (Green LED): Indicates that nominal AC power is present with no wiring faults

detected. When this LED is illuminated, AC power is safe for connected equipment.

* If the Line Fault (Red LED) indicator illuminates, carefully check the AC receptacle

the PDU is plugged into. The receptacle must be tight and securely grounded. A loose

AC receptacle may cause the Line Fault LED to illuminate. The Red LED indicates the

presence of a wiring fault, but does not indicate the exact nature of the fault. Only

qualified electricians should make necessary outlet repairs.

If the Line Fault indicator illuminates and power is not present at the outlets, the

PDU’s surge-suppression components have been compromised as a result of surge

damage. For service, call Tripp Lite Customer Support at 773.869.1234 to remedy the

problem or receive instructions about return, repair or exchange.

14-08-270-9333B9.indb 5 9/15/2014 4:09:44 PM

Warranty & Product Registration

LIMITED WARRANTY

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and

workmanship for a period of 5 years (except internal UPS system batteries outside USA and Canada, 1 year) from the date of initial

purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the

product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all

shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609 USA. Seller will pay return shipping

charges. Visit www.tripplite.com/support before sending any equipment back for repair.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT.

SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT

PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE

LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND

CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not

allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the

use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as

to the suitability or fitness of these devices for any specific application.

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a

chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series

number. The series number can be found on the product nameplate label, along with all required approval markings and

information. When requesting compliance information for this product, always refer to the series number. The series number should

not be confused with the marking name or model number of the product.

The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

14-08-270-9333B9.indb 6 9/15/2014 4:09:44 PM

PDU con Medidor Digital para

Rack con Protección contra

Sobretensiones isobar®

PDUMH15-ISO

(Número de Serie: AGIB7403) PDUMH20-ISO

(Número de Serie: AGIB7410)

Instrucciones de seguridad importantes 8

Advertencias importantes 8

Instalación 9

Características 10

Garantía 12

English 1

Français 13

Manual del propietario

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

14-08-270-9333B9.indb 7 9/15/2014 4:09:45 PM

Instrucciones de seguridad importantes

GUARDE ESTAS INSTRUCCIONES

Este manual contiene instrucciones y advertencias que deben seguirse

durante la instalación, operación y almacenamiento de este producto.

De no seguirlas, se anulará la garantía del producto.

Advertencias importantes

• El PDU provee protección contra sobretensiones y ruido en la línea a os equipos conectados a

través de sus tomacorrientes.

• El PDU está diseñada solo para uso en interiores en un entorno controlado lejos de humedad

excesiva, temperaturas extremas, contaminantes conductivos, polvo o luz del sol directa.

• El PDU debe ser instalado solamente por un técnico calificado.

• No intente instalar el PDU en una superficie inestable o no segura.

• Instale de acuerdo con los reglamentos eléctricos locales. Asegúrese de usar para la instalación

la protección adecuada contra sobrecorriente, de acuerdo con la especificación de la clavija o

del equipo.

• Conecte el PDU a un tomacorriente que esté de acuerdo a los códigos locales de construcción

y que esté correctamente protegido contra corrientes excesivas, cortocircuitos y fallas de

conexión a tierra.

• Los tomacorrientes eléctricos que suministran energía al equipo deben instalarse próximos al

equipo y ser fácilmente accesibles.

• No conecte El PDU a un toma corriente que no esté a tierra o cables de extensión o

adaptadores que eliminen la conexión a tierra.

• Asegúrese de proporcionar un dispositivo local de desconexión, que sea fácilmente accesible,

en cualquier modelo que esté instalado permanentemente sin una clavija.

• Nunca intente instalar equipos eléctricos durante una tormenta eléctrica.

• El equipo individual conectado al PDU no debe consumir más corriente que la de la

especificación de cada tomacorriente individual del PDU.

• La carga total conectada al PDU no debe exceder la capacidad de carga máxima del PDU.

• No intente modificar el PDU, las clavijas de entrada o los cables de alimentación.

• No perfore ni intente abrir ninguna parte del gabinete del PDU. No tiene partes a las que el

usuario pueda dar servicio.

• No intente usar el PDU si se daña cualquier parte.

• El uso de este equipo en aplicaciones de soporte de vida en donde la falla de este equipo

pueda razonablemente hacer suponer que causará fallas en el equipo de soporte de vida o

afecte significativamente su seguridad o efectividad, no está recomendado. No use este equipo

en la presencia de una mezcla anestésica inflamable con aire, oxigeno u óxido nitroso.

14-08-270-9333B9.indb 8 9/15/2014 4:09:45 PM

Instalación

Nota: Las ilustraciones pueden ser un poco diferentes a las de su modelo de PDU.

1-1

1-3

1-2

1-4

1Determine la configuración de la

instalación. La PDU soporta cuatro

configuraciones básicas de instalación:

Bastidor de 1U, bastidor de 0U, de pared

y debajo de mostrador. Elija una

configuración y siga las instrucciones de

instalación en la sección apropiada del

Paso 1 antes de continuar al Paso 2.

Nota: Independientemente de la

configuración, el usuario debe determinar

la idoneidad de los materiales y

accesorios así como de los procedimientos

antes del montaje. La PDU y el material

incluido están diseñados para racks

(bastidores) y cajas de rack (bastidor)

comunes, y pueden no ser apropiados

para todas las aplicaciones.

1-1 Instalación en bastidor de 1U. Fije la

PDU al bastidor insertando cuatro tornillos

suministrados por el usuario (A) a través

de los soportes de montaje (B) de la PDU

en los agujeros de montaje del riel del

bastidor como se muestra.

1-2 Instalación en bastidor de 0U. Parte 1:

Retire los tornillos (C) que fijan los

soportes de montaje a la PDU, cambie la

orientación de los soportes como se

muestra y fíjelos nuevamente. Use solo

los tornillos incluidos o sus equivalentes

exactos (#6-32, 6.4 mm [1/4 pulgada]

de cabeza plana). Parte 2: Fije la PDU

verticalmente insertando dos o más

tornillos suministrados por el usuario (A) a

través de los soportes de montaje (B) de

la PDU en los puntos de montaje en el

bastidor o la caja del bastidor.

1-3 Instalación en la pared. Después de

repetir la Parte 1 anterior, fije el PDU en

una superficie estable para su instalación

insertando dos o más tornillos

suministrados por el usuario (A) a través

de los soportes de instalación del PDU (B)

en los puntos seguros para su instalación

en la superficie de instalación.

1-4 Instalación debajo de mostrador.

Después de repetir la Parte 1 anterior, fije

el PDU en una superficie estable para su instalación insertando quatro tornillos suministrados

por el usuario (A) a través de los soportes de instalación del PDU (B) en los puntos seguros

para su instalación en la superficie de instalación.

14-08-270-9333B9.indb 9 9/15/2014 4:09:46 PM

Amperímetro: La corriente eléctrica total usada por la unidad de

distribución de potencia (PDU) será mostrada en el medidor digital,

en amperios.

Enchufe de entrada (Varía por Modelo)

Salidas (Varía por Modelo): Durante la

operación normal, las salidas distribuyen

energía CA al equipo conectado.

Interruptor automático: Si la corriente consumida por el equipo

conectado al PDU excede la máxima capacidad de corriente, el

interruptor automático disparará para evitar posibles daños. Cuando

un interruptor automático dispara, su émbolo se extiende.

Desconecte el equipo en exceso y permita que el interruptor

automático se enfríe un minuto antes de presionar el émbolo para

restablecer el interruptor automático.

Características

NEMA 5-15P NEMA L5-20P

NEMA 5-15R NEMA 5-15/20R

Instalación

2Conecte el enchufe de entrada de la

PDU a un contacto conectado a tierra.

Inserte el enchufe directamente en una

toma de corriente alterna conectada a

tierra que no comparta el circuito con

alguna carga eléctrica pesada (como un

aire acondicionado o una refrigeradora).

Nota: Modelos selectos incluyen un

adaptador de clavija de entrada que

convierte la clavija de entrada de media

vuelta a una clavija de entrada de pala

recta. Conecte el adaptador de la clavija

de entrada a la clavija de entrada si

desea enchufar el PDU a una toma de

corriente de pala recta compatible.

3Conecte equipos a la PDU. Tenga

cuidado de no exceder la capacidad de

carga de la PDU. La corriente eléctrica

total usada por la unidad de distribución

de potencia (PDU) será mostrada en el

medidor digital, en amperios.

14-08-270-9333B9.indb 10 9/15/2014 4:09:46 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Tripp Lite Stromverteilungseinheit Handbücher

Tripp Lite

Tripp Lite PDUMV15NET Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15HVAT Bedienungsanleitung

Tripp Lite

Tripp Lite SUDC Series Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMVR30NET (AG-0045) Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15HVNET Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV20HVNET Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMNV30HVNET Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3MV6L2120B Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline B020-016 6 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH30HV6 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV15-24 Bedienungsanleitung

Tripp Lite

Tripp Lite SUPDMB568HW Bedienungsanleitung

Tripp Lite

Tripp Lite PDUH20DV Bedienungsanleitung

Tripp Lite

Tripp Lite PDU Bedienungsanleitung

Tripp Lite

Tripp Lite PDU1220T Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH30NET Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3VS6L2120 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH20HV Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15AT Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH20 Bedienungsanleitung

Tripp Lite

Tripp Lite Power Distribution Unit (PDU) PDU6K Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMNV30HVLX Bedienungsanleitung

Tripp Lite

Tripp Lite PDU1215 Bedienungsanleitung

Beliebte Stromverteilungseinheit Handbücher anderer Marken

hager

hager SP 015 Bedienungsanleitung

Pakedge

Pakedge PowerPak 9 Bedienungsanleitung

Pts

Pts 9042 Series Bedienungsanleitung

Shure

Shure WA405 Bedienungsanleitung

CORNING

CORNING CCH 4U Bedienungsanleitung

Panamax

Panamax M4LT-EX Bedienungsanleitung

PANCONNECT

PANCONNECT FLAT 3M Bedienungsanleitung

Raytheon

Raytheon 138-118 Bedienungsanleitung

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Bedienungsanleitung

Botex

Botex PSA 322-6 DL Bedienungsanleitung

GE QuiXtra 4000 Kurzanleitung

RDL

RDL EZ Series Bedienungsanleitung

StarTech.com

StarTech.com RKPW161915 Systemhandbuch

Vertiv

Vertiv Knürr DI-Strip Rack PDU Bedienungsanleitung

ABB

ABB PSBS0065 Handbuch

Baumuller

Baumuller BFN 3-1-0007-001 Handbuch

Eaton

Eaton StructuredWiringSolutions ESWT41600 Handbuch

GE GEK-45404F Bedienungsanleitung