Tripp Lite PDUMH15AT Bedienungsanleitung

Owner’s Manual

1. Important Safety Instructions 2

2. Installation 2

2.1 Mounting the PDU 2

2.2 Connecting the PDU 3

2.3 Networking the PDU 5

2.4 Dynamic IP Address Assignment 5

2.5 Static IP Address Assignment 5

2.6 Testing Network Connection 7

3. Features 8

4. Conﬁguration and Operation 10

4.1 Automatic Transfer Switch 10

4.2 Remote Monitoring and Control 11

5. Technical Support 12

6. Warranty and Warranty Registration 12

Español 13

Français 25

Warranty

Registration

to win a FREE Tripp Lite product!

www.tripplite.com/warranty

PDUMH15AT,PDUMH15ATNET

PDUMH20AT,PDUMH20ATNET

Switched/Metered Rack PDU with

Automatic Transfer Switch

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

201011143 93-2857.indb 1 12/8/2010 2:03:47 PM

2.1A A

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be

followed during the installation, operation, and storage of this product.

Failure to heed these instructions and warnings will void the product

warranty.

2.1 Mounting the PDU

The PDU supports 1U Rack configurations.

Note: The user must determine the fitness of hardware and procedures before mounting. The PDU and included

hardware are designed for common rack and rack enclosure types and may not be appropriate for all

applications. Exact mounting configurations may vary.

• The PDU provides convenient multiple outlets, but it DOES NOT provide surge or line noise

protection for connected equipment.

• The PDU is designed for indoor use only in a controlled environment away from excess moisture,

temperature extremes, conductive contaminants, dust or direct sunlight.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• The power requirement for each piece of equipment connected to the PDU must not exceed the

individual outlet’s load rating.

• The total power requirement for equipment connected to the PDU must not exceed the

maximum load rating for the PDU.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to modify the PDU, including the input plugs and power cables.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Never attempt to install electrical equipment during a thunderstorm.

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended. Do not use this equipment in the presence of a

flammable anesthetic mixture with air, oxygen or nitrous oxide.

2. Installation

1. Important Safety Instructions

2.1A 1U Rack Mounting: Attach the PDU to

the rack by inserting four user-supplied screws

Athrough the PDU mounting brackets Band

into the mounting holes of the rack rail as

shown.

201011143 93-2857.indb 2 12/8/2010 2:03:48 PM

2.1C

2.2

PDUMH20AT

PDUMH20ATNET

PDUMH20AT

PDUMH20ATNET

PDUMH15AT

PDUMH15ATNET

2.2A

2.1B

PDUMH15AT

PDUMH15ATNET

2.1B Wall or 2.1C Under-Counter

Mounting: Remove the screws Cattaching

the mounting brackets to the PDU, change the

orientation of the brackets as shown and

reattach the brackets. Use only the screws

supplied by the manufacturer or their exact

equivalent (#6-32, 1/4” flat head). Attach the

PDU to a stable mounting surface by inserting

two or more user-supplied screws Athrough

the PDU mounting brackets Band into secure

points on the mounting surface.

2.2 Connecting the PDU

The PDU includes two AC power inputs: Primary

and Secondary. The Primary input cord is

permanently attached to the rear of the PDU.

The Secondary input cord is detachable and

connects to the IEC power inlet 2at the rear

of the PDU (PDUMH15AT,PDUMH15ATNET -

IEC-320-C14 inlet; PDUMH20AT,

PDUMH20ATNET - IEC-320-C20 inlet).

2.2A To connect the Secondary input

cord:

1. Form a loop in the Secondary cord Aand

secure the juncture of that loop to the

Primary cord Bwith a zip tie. Be sure the zip

tie is secured around the Secondary and

Primary cords, as well as through the loop

created in the Secondary cord C. (See

diagram). Note: Give the cord as much slack

as possible between the loop and the cord’s

outlet.

2. Once you’ve secured the two cords together

and ensured that the Secondary cord has a

comfortable amount of slack, insert the

Secondary cord outlet into the IEC power

inlet.

2. Installation (continued)

201011143 93-2857.indb 3 12/8/2010 2:03:49 PM

2.2B

2.2C

PDUMH20AT,

PDUMH20ATNET

PDUMH20AT,

PDUMH20ATNET

PDUMH15AT,

PDUMH15ATNET

PDUMH20AT,

PDUMH20ATNET

PDUMH15AT,

PDUMH15ATNET

2.2D

2. Installation (continued)

2.2B Connect Input Plug Adapters

(Optional - Models PDUMH20AT,

PDUMH20ATNET Only): The PDU includes two

adapters that convert one or both of the

L5-20P input plugs to 5-20P input plugs.

Connecting the adapters is optional. The PDU

will function normally without connecting the

adapters.

2.2C Connect Secondary Input Cord to

PDU: Although the PDU will operate without

connecting the Secondary input cord, the

Secondary input is required for the PDU's

Automatic Transfer Switch function.

2.2D Connect PDU Input Plugs: (See the

Configuration and Operation section for more

information.) Connect the Primary input plug A

to a preferred source of grounded 120V AC

power, such as a SmartOnline™UPS System.

The UPS system must not share a circuit with a

heavy electrical load (such as an air conditioner

or refrigerator). Under normal operating

conditions, the PDU will distribute AC power

from the Primary input source. Connect the

Secondary input plug Bto an alternative

source of grounded 120V AC power, such as a

redundant SmartOnline UPS System. The UPS

system must not share a circuit with a heavy

electrical load (such as an air conditioner or

refrigerator). Do not plug the Secondary input

into the same power source as the Primary

input. The PDU will distribute AC power from

the Secondary input only if the Primary input

becomes unavailable.

Note: Immediately after the PDU is connected to live

AC power, you may notice a series of soft clicking

sounds emitted by electrical relays within the PDU.

The relays may also click occasionally during the

operation of the PDU. This is normal.

201011143 93-2857.indb 4 12/8/2010 2:03:50 PM

2.2E

PDUMH20ATNET

PDUMH15ATNET

PDUMH20AT

PDUMH15AT

2.4A

2. Installation (continued)

2.2E Connect Equipment to PDU: Do not exceed the load rating of the PDU. The total

electrical current used by the PDU will be displayed on the digital meter in amperes. Each outlet

includes a green LED that illuminates when the outlet is receiving AC power.

2.3 Networking the PDU (Only Applicable to Models with SNMP Network Card Installed)

Note: The MAC address of the PDU (a 12-digit string in this format: 000667xxxxxx) is printed on a label attached

to the PDU enclosure. The MAC address is also printed on a label attached to the internal network card.

If your network's DHCP server will assign a dynamic IP address to the PDU automatically, go to

Step 2.4A . If you will assign a static IP address to the PDU manually, go to Step 2.5A . If you are

uncertain which method to use, contact your network administrator for assistance before

continuing the installation process.

2.4 Dynamic IP Address Assignment

2.4B Discover IP Address: Contact your network administrator to determine which dynamic IP

address has been assigned to the PDU by the DHCP server. The PDU can be identified on the

DHCP server by referring to its MAC address. (The MAC address is a 12-digit string in this format:

000667xxxxxx. Refer to the MAC address label attached to the PDU.) You may wish to request a

long-term lease period for the IP address, depending on your application. After you have discovered

the IP address, skip Steps 2.5A through 2.5F and proceed directly to Step 2.6A .

2.5 Static IP Address Assignment

2.5A Determine IP Information: Before assigning a static IP address, you'll need to know the

IP address, gateway address and subnet mask. If you do not have this information, contact your

network administrator for assistance.

2.4A Connect PDU to Network: While the

PDU is powered, connect a standard Ethernet

patch cable to the RJ-45 Ethernet port Aon

the PDU. Note: This port is not compatible with

PoE (Power over Ethernet) applications. The

PDU will attempt to obtain an IP address via

DHCP. This may take as long as several

minutes, depending on your network

environment.

201011143 93-2857.indb 5 12/8/2010 2:03:51 PM

2.5C

2.5D

2. Installation (continued)

2.5B Configure Terminal Emulation

Program: Open a VT100-compatible terminal

emulation program (such as the HyperTerminal

program bundled with Microsoft®Windows®)

on a computer with an available DB9 serial

port. (A notebook computer may be the most

convenient choice.) Set the terminal emulation

program to use the COM port Athat

corresponds to the computer’s DB9 serial port.

Specify the parameters Brequired to

communicate with the PDU terminal interface:

Bits per second: 9600

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

If the terminal emulation program supports

multiple emulation modes, you may also need

to specify VT100 emulation C.

2.5C Connect PDU to Computer: Use the

mini-DIN to DB9 serial cable (part number

73-1025) included with the PDU to connect

the PDU to the computer. The circular

connector Aat one end of the cable attaches

to the 8-pin mini-DIN serial port Bon the

PDU. (Align the connector carefully to avoid

damaging the pins.) The DB9 connector Cat

the other end of the cable connects to the

computer's serial port D.

2.5D Connect PDU to Network: While the

PDU is powered, connect a standard Ethernet

patch cable to the RJ-45 Ethernet port Aon

the PDU. Note: This port is not compatible with

PoE (Power over Ethernet) applications.

2.5E Configure PDU in Terminal Mode:

After a brief pause, an initialization page

should appear in the terminal emulation

program. Press any key on the keyboard within

10 seconds to change the PDU settings. (If the

10-second period has elapsed, you can reboot

the PDU by powering down completely and

then restoring power.)

Follow the sequence of responses below in

201011143 93-2857.indb 6 12/8/2010 2:03:52 PM

2.5E

2. Installation (continued)

order to assign an IP address to the PDU. The

default terminal mode root password is

TrippLite. Sample IP settings are shown -

supply your own IP information when you

configure your PDU.

Press A to Accept the settings, or M to Modify? M

Enter the root password: *********

Reset configuration to default values (Y/N)? N

For each of the following questions, you can

press <Return> to select the value shown in

braces, or you can enter a new value.

NETWORK INTERFACE PARAMETERS:

Should this target obtain IP settings from the network?[N] N

Static IP address [192.168.1.19]? 192.168.0.123

Static IP address is 192.168.0.123

Subnet Mask IP address [255.255.0.0]? 255.255.255.0

Subnet Mask IP address is 255.255.255.0

Gateway address IP address [192.168.1.1]? 192.168.0.1

Gateway address IP address is 192.168.0.1

You can also change the root password, real-time clock and other settings. (Tripp Lite recommends

against changing the default settings unless you are an advanced user with a specific purpose.)

After you have finished entering settings, the PDU will save changes to memory and reboot (this

may take several minutes). After the PDU reboots, the initialization page should display the new

static IP settings.

2.5F Remove Serial Cable: Remove the serial cable from the PDU and proceed to Step 2.6A .

2.6 Testing Network Connection

2.6A Access PDU with Web Browser:

After an IP address has been assigned to the

PDU, attempt to access it with a Web browser

that supports frames, forms and Java™. Open

a Web browser on a computer connected to

the LAN and enter the IP address assigned to

the PDU. You should be prompted for a

password A. The user name is admin and the

default password is admin. After you enter the

user name and password, the PowerAlert

Status page Bwill appear in the browser

window. For more information about

configuration and operation of the PDU via the

PowerAlert interface, refer to the

SNMPWEBCARD User's Guide, included on the

CD-ROM bundled with the PDU.

Note for Network Management System Users Only:

Two MIB files - Tripplite.mib and RFC1628.mib - must

be loaded on each Network Management Station that

will monitor the PDU via SNMP. The files are provided

on the CD-ROM included in the product package.

201011143 93-2857.indb 7 12/8/2010 2:03:52 PM

Primary AC Input Power Cord (Model

PDUMH15AT/15ATNET):The cord is permanently attached to the

PDU and has a NEMA 5-15P plug.

NEMA 5-15/20R Outlets (Model PDUMH20AT/20ATNET):

During normal operation, the outlets distribute AC power to

connected equipment. When an outlet is live, the associated LED

illuminates.

Primary AC Input Power Cord (Model PDUMH20AT/20ATNET):

The cord is permanently attached to the PDU and has a NEMA

L5-20P plug.

Secondary AC Input Power Inlet (Model

PDUMH15AT/15ATNET): The IEC-320-C14 inlet connects to the

detachable Secondary AC Input Power Cord.

Secondary AC Input Power Inlet (Model

PDUMH20AT/20ATNET): The IEC-320-C20 inlet connects to the

detachable Secondary AC Input Power Cord.

Secondary AC Input Power Cord (Model

PDUMH15AT/15ATNET): The detachable cord has an IEC-320-C13

connector and a NEMA 5-15P plug.

Secondary AC Input Power Cord (Model

PDUMH20AT/20ATNET): The detachable cord has an IEC-320-C19

connector and a NEMA L5-20P plug.

Input Plug Adapters (Model PDUMH20AT/20ATNET): The

adapters convert NEMA L5-20P input plugs to NEMA 5-20P input

plugs.

NEMA 5-15R Outlets (Model PDUMH15AT/15ATNET): During

normal operation, the outlets distribute AC power to connected

equipment. When an outlet is live, the associated LED illuminates.

3. Features

201011143 93-2857.indb 8 12/8/2010 2:03:53 PM

Network Operating Conditions

ALink LED Color BStatus LED Color

Off No Network Connection Off Card Not Initialized

Flashing Amber 100 Mbps Network Connection Steady Green Card Initialized and Operational

Flashing Green 10 Mbps Network Connection Flashing Amber Error - Card Not Initialized

Digital Load Meter (Ammeter): The total electrical current used

by the PDU is displayed on the digital meter in amperes.

Input Source Indicator: When the PDU is connected to a live AC

power source, the Primary or Secondary input LED illuminates to

indicate which source is supplying power to the PDU outlets.

Accessory Slot: An optional SNMP card may be installed in the

slot, allowing the PDU to be configured, controlled and monitored

remotely. Contact Tripp Lite Customer Support at (773) 869-1234

for more information.

Factory Port: The port is reserved for configuration by factory

authorized personnel only. Do not connect anything to the port.

For Models with SNMP Network Card Installed:

PS/2 Port: Use this port to connect a Tripp Lite ENVIROSENSE

environmental sensor to provide remote temperature/humidity

monitoring and a dry contact interface to control and monitor alarm,

security and telecom devices. Contact Tripp Lite Customer Support

at (773) 869-1234 for ordering information. Note: Do not connect

a keyboard or mouse to this port.

Mini-DIN Serial Port: Use this port to provide a direct terminal

connection to a computer with a terminal emulation program. A

serial cable (part number 73-1025) is included with the PDU. If you

need to order a replacement cable, contact Tripp Lite Customer

Support at (773) 869-1234.

Ethernet Port: Use this RJ-45 jack to connect the PDU to the

network with a standard Ethernet patch cable. The Link LED Aand

Status LED Bindicate several operating conditions, as shown in the

table below. This port is not compatible with PoE (Power Over

Ethernet) applications.

3. Features (continued)

201011143 93-2857.indb 9 12/8/2010 2:03:54 PM

Facility Circuit Facility Circuit

PDUMH15ATNET

Critical Equipment

Loads

Secondary UPS Primary UPS

Primary Input Cord

Secondary Input Cord

Utility B Utility A

4. Configuration and Operation

4.1 Automatic Transfer Switch

When the Primary and Secondary inputs are both connected to Tripp Lite UPS Systems, the PDU

operates as an Automatic Transfer Switch, providing redundant input power for high availability

applications. Under normal operating conditions, the PDU will distribute power from the Primary

input source, switching to the Secondary input source under certain conditions. The PDU will switch

to the Primary source whenever it is Good according to the PDU input voltage definitions (see

below).

4.1A Preferred Configuration

The Automatic Transfer Switch function provides

increased availability when the Primary and

Secondary inputs of the PDU are connected to

separate Tripp Lite UPS Systems that are

connected to separate utility power sources.

For maximum availability, Tripp Lite

recommends using matching SmartOnline UPS

Systems with pure sine wave output for the

Primary and Secondary input power sources.

The automatic transfer switch function will be

compromised if the primary and secondary

inputs are connected to the same utility power

source.

Warning: DO NOT connect the primary input

to a line-interactive UPS, due to transfer

time issues, or to any source that does not

supply a pure sine wave. Such sources may

be used to power the secondary input.

4.1B Automatic Transfer Switch Source Selection

Upon power-up, the PDU looks for a source ≥85V. If it is unable to find a source ≥85V, it remains

off.

Input voltage definitions:

99V ≤Vin < 139V Good

75V ≤Vin < 99V Fair

Vin < 75V Bad

In normal operation (after power-up), if the selected source is no longer Good, the PDU will

attempt to switch to the other source, but only if the other source is Good. If the selected source

becomes Fair and the other source is not Good, the PDU will keep the loads connected to the

selected source until the selected source becomes Bad, at which point the loads will be

disconnected (note that the source selection doesn't change). After the loads are disconnected,

they remain disconnected until the selected source becomes ≥85V, or until the other source

becomes Good.

201011143 93-2857.indb 10 12/8/2010 2:03:54 PM

Andere Handbücher für PDUMH15AT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Tripp Lite Stromverteilungseinheit Handbücher

Tripp Lite

Tripp Lite PDUMV15 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMNH20HV Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15AT Bedienungsanleitung

Tripp Lite

Tripp Lite PDU40TDUAL Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15HVNET Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV30NET Bedienungsanleitung

Tripp Lite

Tripp Lite SUPDM Modules 932645 932645 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUH20DV Bedienungsanleitung

Tripp Lite

Tripp Lite PDU Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3MV6L2130 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV20HV Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMNV30LX Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH20 Bedienungsanleitung

Tripp Lite

Tripp Lite AG-0135 Series Bedienungsanleitung

Tripp Lite

Tripp Lite PDUV20-60 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV30HV Bedienungsanleitung

Tripp Lite

Tripp Lite PDUH20DV Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH20HVNET Bedienungsanleitung

Tripp Lite

Tripp Lite Power Distribution Unit (PDU) PDU6K Bedienungsanleitung

Tripp Lite

Tripp Lite PDU1215 Bedienungsanleitung

Tripp Lite

Tripp Lite PDU40TDUAL Bedienungsanleitung

Tripp Lite

Tripp Lite PDUV30-36 Bedienungsanleitung

Tripp Lite

Tripp Lite SUPDM56HW Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3VS6L2120 Bedienungsanleitung

Beliebte Stromverteilungseinheit Handbücher anderer Marken

hager

hager SP 015 Bedienungsanleitung

Pakedge

Pakedge PowerPak 9 Bedienungsanleitung

Pts

Pts 9042 Series Bedienungsanleitung

Shure

Shure WA405 Bedienungsanleitung

CORNING

CORNING CCH 4U Bedienungsanleitung

Panamax

Panamax M4LT-EX Bedienungsanleitung

PANCONNECT

PANCONNECT FLAT 3M Bedienungsanleitung

Raytheon

Raytheon 138-118 Bedienungsanleitung

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Bedienungsanleitung

Botex

Botex PSA 322-6 DL Bedienungsanleitung

GE QuiXtra 4000 Kurzanleitung

RDL

RDL EZ Series Bedienungsanleitung

StarTech.com

StarTech.com RKPW161915 Systemhandbuch

Vertiv

Vertiv Knürr DI-Strip Rack PDU Bedienungsanleitung

ABB

ABB PSBS0065 Handbuch

Baumuller

Baumuller BFN 3-1-0007-001 Handbuch

Eaton

Eaton StructuredWiringSolutions ESWT41600 Handbuch

GE GEK-45404F Bedienungsanleitung