Tripp Lite Smart On line SUINT1000XL Bedienungsanleitung

Owner’s Manual

1111 W. 35th Street Chicago, IL 60609 USA

Customer Support: (773) 869-1234 • www.tripplite.com

Important Safety Instructions 2

Quick Installation 3

Basic Operation 5

Storage and Service 11

SmartOnline™

• Intelligent, True On-Line Tower UPS Systems • True On-Line Operation

• Pure Sine Wave Output • 220/230/240V Input/Output

Models: SUINT1000XL, SUINT2000XL & SUINT3000XL

Not suitable for mobile applications.

Troubleshooting 9

Optional Installation 4

Español 12

Français 23

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 1

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, conductive contaminants,

dust or direct sunlight.

• For best performance, keep the indoor temperature between between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the

UPS into itself; this will damage the UPS.

• Do not modify the UPS's plug, and do not use an adapter that would eliminate the UPS’s

ground connection.

• Do not use extension cords to connect the UPS to an AC outlet. Your warranty will be

voided if anything other than Tripp Lite surge suppressors are used to connect your UPS

to an outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must

provide clean, filtered, computer-grade output.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction

or failure of a Tripp Lite UPS System could cause failure or significantly alter the

performance of a life-support device.

Battery Warnings

• Your UPS does not require routine maintenance. There are no user-serviceable parts

inside. Do not open your UPS for any reason.

• Since batteries present a risk of electrical shock and burn from high short-circuit current,

observe proper precautions. Unplug and turn off the UPS before performing battery

replacement. Use tools with insulated handles, and replace the existing batteries with the

same number and type of new batteries (sealed lead-acid). Do not open the batteries. Do

not short or bridge the battery terminals with any object.

• The UPS batteries are recyclable. Refer to local codes for disposal requirements. Do not

dispose of the batteries in a fire.

• Do not operate your UPS without batteries.

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these

warnings will void your warranty.

Important Safety Instructions

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 2

Quick Installation

Connection and Start-Up

Plug your UPS into an electrical outlet.

Note: The UPS system does not include an input power cord.

Model SUINT1000XL Only:

Connect a user-supplied power cord to the IEC-

320-C14 input receptacle. The power cord

should have an IEC-320-C13 connector on one

end and a plug appropriate for your local site’s

utility outlets on the other end.

Models SUINT2000XL and SUINT3000XL

Only:

Connect a user-supplied power cord to the IEC-

320-C20 input receptacle. The power cord

should have an IEC-320-C19 connector on one

end and a plug appropriate for your local site’s

utility outlets on the other end.

All Models:

Plug the UPS directly into a properly grounded,

3-wire, AC outlet that does not share a circuit

with a heavy electrical load (such as an air con-

ditioner, refrigerator, etc.). The outlet must have

an amp rating equal to or greater than your

UPS’s input breaker rating.

Note: Once your UPS is plugged in, the fan and all Indicator

Lights will turn ON. The “LINE” and “LOAD ACTIVE

METER” LEDs will illuminate and the UPS will beep to indi-

cate normal operation. However, power is not supplied to

your UPS’s AC outlets until the UPS is turned on.

Plug your equipment into your UPS.

Your UPS is designed to support computer

equipment only. You will overload your UPS if

you connect devices with high power demands

such as household appliances or laser printers to

your UPS’s outlets.

Note: Additional interconnection cords (C13 to C14) are avail-

able from Tripp Lite. Call 773-869-1234 (Part # P004-006).

Turn your UPS ON:

• Press the “ON/TEST” Switch

• Hold it for several seconds until you hear a beep

• Release it

The “ON LINE” LED will now light, and your

UPS will begin providing power to its AC

outlets.

Note: During the initial installation of the UPS, or after

prolonged storage, the internal batteries must charge for 2-4

hours before the UPS can support connected equipment

during a power failure.

SUINT2000XL shown

SUINT1000XL shown

1B SUINT1000XL shown

SUINT2000XL shown

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 3

Optional Installation

The connections are optional. Your UPS will function properly

without these connections.

Serial Port Connection

Using the serial cable provided, connect the

serial port on your computer to the serial port

of your UPS. Install on your computer the

PowerAlert UPS monitoring software pro-

gram (included on CD-ROM) appropriate for

your operating system. See Communications

in the Basic Operation section of this manual

to determine how to monitor and manage your

UPS using this port.

External Battery Pack Connection

Check to ensure that the external batteries you

are connecting match the voltage listed on

your UPS’s battery connector. Plug either end

of the battery connection cable (supplied with

the battery pack) into the UPS’s External

Battery Connector and the other end into the

Battery Output Connector on the rear panel of

the external battery pack. Since your UPS has

internal batteries, external batteries are only

needed to extend runtime. Adding external

batteries will increase recharge time as well as

runtime. Make sure that each end of the cable is

fully inserted into its connector. Several small

sparks may result during battery connection;

this is normal.

SU1000T shown

SUINT2000XL shown

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 4

Important Safety InstructionsBasic Operation

Front Panel Switches

“ON/TEST” Switch: This switch controls four separate UPS functions:

UPS Power ON: To turn the UPS on, press this switch, hold it for

several seconds until you hear a beep, then release it. The “ON LINE”

LED will illuminate.

UPS Self-Test: During normal on-line operation, press this switch

and hold it until you hear a beep. This initiates a 10-second self-test

of the battery. The UPS will shift to battery power (the “ON BATT”

and “BATTACTIVE METER” LEDs will illuminate) for ten seconds.

Alarm Silence: To silence the UPS “on-battery” alarm, press this

switch and hold it until you hear a beep.

UPS Cold Start: To use your UPS as a stand-alone power source

when AC power is unavailable (i.e. during a blackout), press this

switch and hold it until you hear a beep. The UPS will then provide bat-

tery power to its outlets.*

* The “ON BATT” Indicator Light will be illuminated since your UPS will be operating

from battery power.

“OFF” Switch: This switch turns power OFF at the UPS receptacles.

Press this switch, hold it until you hear a beep, then release it. The

UPS will continue charging and the fan will continue to cool internal

components even after you turn the UPS receptacles off. To turn the

UPS OFF completely, including the charger, disconnect the UPS’s

power cord after pressing the “OFF” switch.

“ON LINE” LED: This green light will be lit when the UPS is in normal

on-line operation (filtering and resynthesizing incoming AC line voltage

to provide pure sine wave output). When this light is illuminated, you

can monitor the load level of your UPS on the “LOAD ACTIVE

METER” LEDs.

“LINE” LED: This green light will be lit when the utility-supplied

AC line voltage at your wall outlet is nominal. It will flash if the line

voltage or frequency is outside the nominal range (either too low or

too high). No action is required on your part when the LED flashes;

the UPS continuously and automatically filters AC line power to pro-

vide your equipment with pure sine wave AC power, regardless of

brownout or overvoltage conditions. If this light is off, then AC line

voltage is not present (blackout) or is at an extremely high voltage.

Front Panel Indicator Lights

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 5

Basic Operation

(continued)

Front Panel Indicator Lights

continued

“BYPASS” LED: This yellow light will be lit when the UPS’s

DC/AC inverter is deactivated and the UPS is in the “Bypass” mode.

During normal operation this LED will light briefly when the unit is

plugged in, but if an internal fault or overload occurs this light will

illuminate constantly to show that connected equipment will receive

filtered AC utility power, but will not receive battery power during a

blackout. In this case, contact Tripp Lite for service.

“FAULT” LED: This red light will flash when your UPS detects an

internal fault (overheating, overvoltages, etc.) or when it detects a

wiring fault in your wall outlet (reversed phases, missing ground,

etc.) The UPS will only detect wiring faults when it is plugged into

a utility outlet but not turned ON. If the light persists after restarting

the UPS, contact an electrician to check the AC line. Your UPS will

identify the presence of most (but not all) wiring faults.

“LOAD ACTIVE METER” LED: This green light will illuminate

when your UPS is receiving AC power to indicate that the set of four

dual-function LEDs is displaying the load level of your UPS.

“BATT ACTIVE METER” LED: This green light will be lit when

your UPS is operating from battery power to indicate that the set of

four dual-function LEDs is displaying the battery charge level of your

UPS. The “ON BATT” LED will also be illuminated.

“OVERLOAD” LED: This red light will be lit when your UPS’s capaci-

ty has been exceeded while it is in on-line operation. The UPS alarm will

beep continuously. Immediately remove overload until light and alarm

go off. If you do not immediately remove the overload, the UPS will

transfer from on-line to bypass operation.

“BATT LOW” LED: This yellow light will be lit when your UPS’s

battery charge level is low. The UPS alarm will beep until either the

battery charge is depleted or the batteries are adequately recharged.

“ON BATT” LED: This green light will be lit when AC line voltage

is not present and your UPS is providing your equipment with battery

power. The UPS will also beep every two seconds, unless silenced by

the “ON/TEST” Switch. When this light is illuminated, you can monitor

the battery charge level of your UPS on the “BATT ACTIVE

METER” LEDs.

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 6

“REPLACE BATT” LED: This red light will be lit and the UPS alarm

will beep every 2 seconds if your UPS’s microprocessor detects a

battery fault or if your UPS fails the automatic self-test (after you turn

your UPS ON) and the UPS battery is less than fully charged. Let the

UPS charge for 12 hours, then perform a second self test (Basic

Operation—UPS Self-Test). If the light continues to stay on, contact

Tripp Lite for service.

AC Receptacles: These receptacles provide your connected equipment

with pure sine-wave AC output from the AC line during normal operation

and from battery power during blackouts and severe brownouts.

Power provided at these outlets is filtered to protect connected equipment

against damaging surges and line noise.

Input Receptacle (Model SUINT1000XL Only): Plug the UPS sys-

tem into utility power by connecting a user-supplied power cord to the

IEC-320-C14 input receptacle. The power cord should have an IEC-

320-C13 connector on one end and a plug appropriate for your local

site's utility outlets on the other end. The UPS system does not include

an input power cord.

Input Receptacle (Models SUINT2000XL and SUINT3000XL

Only): Plug the UPS system into utility power by connecting a user-

supplied power cord to the IEC-320-C20 input receptacle. The power

cord should have an IEC-320-C19 connector on one end and a plug

appropriate for your local site's utility outlets on the other end. The

UPS system does not include an input power cord.

Input Circuit Breaker Switch: This resettable breaker prevents high

input current from damaging the UPS or the attached load. If this

breaker trips, make sure your UPS is connected to AC power of the

proper voltage before resetting the circuit breaker by pushing the

breaker switch in.

Fan: The fan cools the UPS’s internal components. It is always on

when line power is present.

Basic Operation

(continued)

Rear Panel

Front Panel Indicator Lights

continued

220/230/240V IEC-320-C13

220/230/240V IEC-320-C14

220/230/240V IEC-320-C20

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 7

Basic Operation

(continued)

“SMART” DB9 Port: Your UPS’s DB9 port can be used to monitor

and control your UPS using the RS-232 protocol.

RS-232 communications are very complex but are easy to implement.

The easiest way to monitor and control the UPS using RS-232 is to connect

the UPS to a computer with a DB9 cable and install Tripp Lite’s

PowerAlert software on the connected computer.

Communications

Rear Panel

continued

External Battery Pack Connector: Use to connect optional Tripp Lite

Battery Packs for additional runtime. Contact Tripp Lite Customer

Support at (773) 869-1234 for the appropriate Tripp Lite battery pack

to connect. Refer to instructions available with the Battery Pack for

complete connection information and safety warnings.

Accessory Slot (Models SUINT2000XL and SUINT3000XL

Only): Remove the small cover panel from this slot to use optional

accessories to remotely monitor and control your UPS. Contact Tripp

Lite Customer Support at (773) 869-1234 for more information,

including a list of available SNMP, network management and connec-

tivity products.

TVSS Cover Plate: Remove this plate to install optional modem/network

surge protection modules, available for purchase by special arrangement

with Tripp Lite.

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 8

The UPS’s control panel lights will turn on in the sequences below to signal that the UPS is

having operational difficulties.

Lights (On/Flashing) and Condition Solution

On: REPLACE BATT Let the UPS system charge for at least

Condition: Replace Battery 12 hours and perform a self test using

the “ON/Test Switch” (

Basic Operation—

UPS Self-Test

). If the light continues to

stay on, contact Tripp Lite for service.

On: BATT LOW, ON BATT Prepare for imminent UPS shutdown.

Condition: Battery Low

On: BYPASS, LINE, LOAD, OVERLOAD Reduce the load the UPS supports.

Condition: On Bypass due to Overload

Flashing: OVERLOAD Remove the cause of the short circuit

Condition: Short Circuit from the UPS output.

On: FAULT, 100% Restart the UPS. If the problem persists,

Condition: Battery Voltage too High contact Tripp Lite for repairs.

On: FAULT, BYPASS, LINE, 50% Restart the UPS. If the problem persists,

Condition: On Bypass due to contact Tripp Lite for repairs.

High Output Voltage

On: FAULT, BYPASS, LINE Restart the UPS. If the problem persists,

Flashing: 50% contact Tripp Lite for repairs.

Condition: On Bypass due to Low

Bus Voltage

On: FAULT, BYPASS, LINE, 25% Restart the UPS. If the problem persists,

Condition: On Bypass due to contact Tripp Lite for repairs.

Low Output Voltage

On: FAULT, BYPASS, LINE Restart the UPS. If the problem persists,

Flashing: 25% contact Tripp Lite for repairs.

Condition: On Bypass due to Low

Bus Voltage

Troubleshooting

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 9

Troubleshooting

(continued)

Lights (On/Flashing) and Condition Solution

On: BYPASS, LINE Check the UPS to be sure that there is

Flashing: FAULT adequate space for air to circulate near

the vents and that the fan is working

properly. Restart the UPS.

Flashing: LINE This indicates that utility power is too high

Condition: Input Abnormal or low for the UPS to operate in BYPASS

mode, so if an inverter failure occurs,

the UPS will deliver no output.

On: FAULT, 50% Restart the UPS. If the problem persists,

Flashing: LINE contact Tripp Lite for repairs.

Condition: No Output due to High

Output Voltage and Abnormal Input

Flashing: LINE, 50%

Restart the UPS. If the problem persists,

On: FAULT contact Tripp Lite for repairs.

Condition: No Output due to Low

Output Voltage and Abnormal Input

Flashing: LINE, Restart the UPS. If the problem persists,

On: FAULT, 25% contact Tripp Lite for repairs.

Condition: No Output due to High

Bus Voltage and Abnormal Input

Flashing: LINE, 25% Restart the UPS. If the problem persists,

On: FAULT contact Tripp Lite for repairs.

Condition: No Output due to Low

Bus Voltage and Abnormal Input

Flashing: LINE, FAULT Check the UPS to be sure that there is

Condition: No Output due to High adequate space for air to circulate near

Internal Temperature and Abnormal the vents and that the fan is working

Input properly. Restart the UPS. If the problem

persists, contact Tripp Lite for repairs.

200604111 93-2525 230V Smartonline OM.qxd 5/8/2006 9:58 AM Page 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Tripp Lite UPS Handbücher

Tripp Lite

Tripp Lite OMNIVS1000 Bedienungsanleitung

Tripp Lite

Tripp Lite ECO750UPS Bedienungsanleitung

Tripp Lite

Tripp Lite AVRX Series Bedienungsanleitung

Tripp Lite

Tripp Lite HTRL15UPS Bedienungsanleitung

Tripp Lite

Tripp Lite SMART1000LCDU Bedienungsanleitung

Tripp Lite

Tripp Lite AGSM5000Y3U3I Bedienungsanleitung

Tripp Lite

Tripp Lite AVRX Series Bedienungsanleitung

Tripp Lite

Tripp Lite BC Internet Bedienungsanleitung

Tripp Lite

Tripp Lite SMX1500LCD Bedienungsanleitung

Tripp Lite

Tripp Lite ECO350UPS Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU1500LCD1U Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro SMART700SER Bedienungsanleitung

Tripp Lite

Tripp Lite OMNIVS1500XLCD Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU8000RT3U Bedienungsanleitung

Tripp Lite

Tripp Lite SUPDM15 Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU750XL Bedienungsanleitung

Tripp Lite

Tripp Lite ECO750UPSTAA Betriebsanleitung

Tripp Lite

Tripp Lite SmartPro SMART1500SLTXL Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline 3-Phase UPS System SU30K3/3XR5 Bedienungsanleitung

Tripp Lite

Tripp Lite OMNISMART OMNIVS500 Bedienungsanleitung

Tripp Lite

Tripp Lite SMART1200LCD Bedienungsanleitung

Tripp Lite

Tripp Lite SMART1000LCDTAA Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline 5KVA Bedienungsanleitung

Tripp Lite

Tripp Lite 1250-3000 VA Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung