Tripp Lite SmartPro 450 RT Bedienungsanleitung

1111W.35thStreet

Chicago, IL 60609 USA

CustomerSupport:(773)869-1234

www.tripplite.com

Installation: p. 3 - 4

Basic Operation: p. 5 - 7

Storage & Service: p. 8

Specifications: p. 8

Safety: p. 2

Owner's Manual

SmartPro®450 RT

Intelligent Network UPS System (120V)

ESPAÑOL: p. 9

FRANÇAIS: p. 17

200007222 Smart 450 RT Owners Manual [120 Volt].p65 9/7/00, 5:16 PM1

This manual contains important instructions and warnings that should be

followed during the installation, operation and storage of all Tripp Lite UPS

Systems.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, dust or

direct sunlight.

• For best performance, keep the indoor temperature between 32° F and

104° F (between 0° C and 40° C).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS to a three-wire, grounded AC power outlet. Do not

remove or modify the ground pin of the UPS's plug.

• Do not use two-prong adapters with the UPS's plug. Do not plug your UPS

into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator,

the generator must provide clean, filtered computer-grade output.

• Use only the power supply cord provided with this unit. The power cord for

the UPS is wired in accordance with National Electrical Code (NEC) specifi-

cations. Be sure that your wall outlet is also wired to these specifications.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support applications in which

a malfunction or failure of a Tripp Lite UPS System could cause failure or

significantly alter the performance of a life-support device.

Battery Warnings

• Your UPS does not require routine maintenance. Do not open your UPS

for any reason. There are no user-serviceable parts inside.

• Battery replacement must be performed by qualified service personnel.

Because the batteries present a risk of electrical shock and burn from high

short-circuit current, qualified service personnel should observe proper

precautions: Unplug and turn off the UPS before performing battery

replacement. Use tools with insulated handles and replace the existing

batteries with the same number and type of new batteries (Sealed Lead-

Acid). Do not open the batteries. Do not short or bridge the battery termi-

nals with any object.

• The UPS batteries are recyclable. Refer to local codes for disposal require-

ments or in the USA only call 1-800-SAV-LEAD (1-800-728-5323) for

complete recycling information. Do not dispose of the batteries in a fire.

• Do not attempt to add external batteries.

Safety

200007222 Smart 450 RT Owners Manual [120 Volt].p65 9/7/00, 5:16 PM2

Mounting

Rackmount

Position brackets as shown in Figure 1

to serve as mounting ears for the UPS

in your rack. Use 4 mounting screws

and washers to connect the UPS to

each bracket. Mount the UPS in your

rack with user-supplied screws and hardware appropriate to your rack. Have an

assistant hold the UPS in position while mounting.

Desktop/Under-Monitor

Place on your desktop or under your computer monitor with the control and LED

panel forward. CAUTION: Do not place more than 50 lb. (22.7 kg) on your UPS.

Vertical Tower

Position brackets as shown in Figure 2 to serve as stabilizers for the UPS in a

vertical position. Use 2 flattop mounting screws to connect the UPS to each

bracket. Make sure the control and LED panel is at the top. To prevent dust from

settling inside the UPS, fill the empty upward-facing holes with the plastic

plugs included.

Wallmount

To mount the UPS perpendicular to a wall along a straight, vertical line, first

position brackets on the UPS's sides as shown in Figure 3. Adjust brackets to

desired distance from wall. Use 4 mounting screws and washers to connect the

UPS to each bracket. Mount UPS to your wall with user-supplied screws and

hardware appropriate to the composition of the wall. Have an assistant hold the

UPS in position while mounting. Make sure the control and LED panel is at the

top. Additional bracket holes allow you to mount up to two UPSs side-by-side

on the same set of brackets (Figure 4). CAUTION: each UPS weighs 15-1/2 lbs.

(7 kg). Be sure that user-supplied mounting hardware can support this weight.

Installation

Figure2–VerticalTower Figure 3 – Wallmounting One UPS Figure 4 – Wallmounting

TwoUPSs

Figure1 – Rackmount

200007222 Smart 450 RT Owners Manual [120 Volt].p65 9/7/00, 5:16 PM3

Plug one end of the

detachable line cord

into your UPS's AC

Inlet Receptacle and

the other end into an

electrical outlet.

Plug your computer,

monitor and other

critical devices into your

UPS's Battery-Supported

Receptacles.*

Plug a printer or other

peripheral equipment

into your UPS's Surge-

Only Receptacle.

–Optional–

Using Tripp Lite cable, connect

the serial port of your computer

to the serial port of your UPS.**

Load software and run

installation program appropriate

to your operating system.

Turn your UPS ON

by pressing the Main

Power Switch, holding

it for 3 seconds and

releasing it.***

* Your UPS is designed to support only computer equipment. You will overload your UPS if you connect household

appliances, laser printers or surge suppressors to the UPS's Battery-Supported Outlets. ** DB9 port connection is

optional. Your UPS will function properly without this connection. *** The UPS will execute a 10-second self-test.

The "Normal" LED will illuminate and the UPS will emit one beep to indicate normal operation.

Connection

200007222 Smart 450 RT Owners Manual [120 Volt].p65 9/7/00, 5:16 PM4

Switch

1. Main Power Switch

This switch activates three separate UPS functions:

UPS Power

Press the switch, hold it for 3 seconds and release it to turn the UPS

ON or OFF.*

Alarm Silence

Press the switch and immediately release it to silence the UPS Alarm.

UPS Cold Start

Press the switch, hold it for 5 seconds and release it to turn your UPS

ON and to use it as a stand-alone power source (operating from the

battery without AC input).**

* The UPS will execute a 10-second self-test when you turn it on. The “Normal" LED will illuminate, and the UPS will beep once

to indicate the UPS is turned ON. If the UPS alarm sounds and the "Replace Battery" LED illuminates, turn your UPS OFF, let

your UPS charge its batteries for 12 hours and turn UPS back ON to repeat the automatic self-test. If alarm still sounds, contact

Tripp Lite for service. CAUTION: Do not unplug your UPS to test its batteries. This will remove safe electrical grounding and may

introduce a damaging surge into your network connections.

** The "Backup" LED will illuminate since your UPS will operate from battery power.

Basic Operation

234 5

12 14

Front

Back

13 1

200007222 Smart 450 RT Owners Manual [120 Volt].p65 9/7/00, 5:16 PM5

Indicator Lights

The SmartPro 450 RT utilizes dual function Indicator Lights that alert you to

different information depending on whether they illuminate constantly or are

flashing. All Indicator Light Descriptions refer to when the UPS is connected to

the wall outlet and turned ON.

2. "AC Normal/AVR" LED

This green light will illuminate constantly to indicate the utility-supplied AC

line voltage at your wall outlet is normal. It will flash to indicate your UPS is

automatically correcting high or low AC line voltage (AVR=Automatic Voltage

Regulation). The longer the UPS is correcting voltage, the longer the LED will

flash. This is a normal, automatic operation of your UPS, and no action is required

on your part.

3. "Backup/Low Batt" LED

This yellow light will illuminate constantly to indicate your UPS is providing

your equipment with battery power. (The UPS's Alarm will sound once every

15 seconds.) The light will flash when the UPS's battery is low and the UPS

is initiating an automatic system shutdown. (The UPS's Alarm will sound once

every second for approximately 2 minutes, depending on load, prior to shut-

down).

4. "Fault/Overload" LED

This red light will illuminate constantly to indicate a short circuit in the UPS

or other fault. The light will illuminate and the UPS's Alarm will sound constantly

for 30 seconds before the UPS automatically shuts down. The light will flash

(and the UPS's Alarm will sound once each second) when the UPS's capacity has

been exceeded while it is operating from battery power. Immediately remove

overload from battery-supported outlets.

5. "Replace Batt" LED

This red light will illuminate constantly if your UPS fails the automatic self-test

(after you turn your UPS ON) and the UPS battery is less than fully charged.

Turn the UPS OFF and let it charge for 12 hours and turn it back ON to perform

a second automatic self-test. If the light continues to stay on, contact Tripp Lite

for service.

6. "Wiring Fault" LED

This red light on the back of the UPS shines constantly when your UPS detects

a wiring fault in your wall outlet (reversed phases, missing ground, etc.) Have

an electrician fix the fault immediately. Your UPS will identify the presence of

most (but not all) wiring faults.

200007222 Smart 450 RT Owners Manual [120 Volt].p65 9/7/00, 5:16 PM6

Other UPS Features

7. AC Receptacles (Battery Backup Supported)

These receptacles provide your connected equipment with AC line power during

normal operation and battery power during blackouts and brownouts. They also

protect your equipment against damaging surges and line noise. Connect com-

puter, monitor and other essential equipment to these receptacles.

8. AC Receptacle (Surge-Only)

This receptacle provides equipment that does not require battery backup (such

as printers) with complete surge and line noise protection. Do not connect

computers or other essential equipment to this receptacle.

9.“SMART” RS-232 Port

The RS-232 port connects your UPS to any PC or workstation. Use with Tripp Lite

software and cabling to monitor and manage network power and automatically

save open files and shut down equipment during a blackout. This port uses

RS-232 communications to transmit UPS and power conditions.

10. Accessory Slot

Contact Tripp Lite Customer Support for more information and a list of available

SNMP, network management and connectivity products.

11. Mounting Brackets

The mounting brackets are already set for mounting in standard 19 in. racks.

See Installation section for using the mounting brackets to suit under-monitor,

tower and wallmount applications.

12. AC Inlet Receptacle

Connect one end of the detachable line cord into this receptacle and the other end

into your wall outlet.

13. Battery Replacement Door

Under normal conditions, the original battery in your UPS will last several years.

Battery replacement should be performed only by qualified service personnel.

Refer to “Battery Warnings” in the Safety section. When replacing batteries,

qualified service personnel should follow this procedure: 1) turn UPS OFF; 2)

remove the snap-on battery replacement door, on left front of unit; 3) pull

batteries partially out of case; 4) make a detailed sketch of the batteries and the

polarity, color and connection of all cables; 5) disconnect battery terminals; 6)

dispose of used batteries; 7) reconnect replacement batteries exactly as original

batteries were; 8) push batteries back into case and replace cover.*

* You may not receive full runtime until your replacement batteries have fully charged.

14. Circuit Breaker

This resettable circuit breaker protects equipment plugged into AC receptacles

against short circuits and system overloads. If the circuit breaker trips, unplug

at least one piece of equipment from the AC receptacles and reset the breaker

by pressing the button back into place.

200007222 Smart 450 RT Owners Manual [120 Volt].p65 9/7/00, 5:16 PM7

Specifications

Storage & Service

Storage

First turn your UPS OFF and disconnect its power cord from the wall outlet.

Then disconnect all equipment to avoid battery drain. If you plan on storing

your UPS for an extended period of time, fully recharge the UPS batteries once

every three months by plugging the UPS into a live AC outlet, turning the Power

Switch ON and letting the UPS charge for 4-6 hours. If you leave your UPS

batteries discharged for an extended period of time, they will suffer permanent

loss of capacity.

Service

If returning your UPS to Tripp Lite, please carefully pack the UPS using the

ORIGINAL PACKING MATERIAL that came with the unit. Enclose a letter

describing the symptoms of the problem. If the UPS is within the 2 year warranty

period, enclose a copy of your sales receipt.

Model SMART 450 RT

Output Capacity (VA/Watts): 450/270

Battery Runtime (Half Load/Full Load) Min.: 12/3

Battery Recharge Rate: 2-4 hrs.

Approvals: UL 1778, cUL, FCC Class B

Input Voltage (120V); Input Frequency (50/60 Hz Auto-Selecting); On-Line Input Voltage Range (86 - 147 volts); Voltage-Regulated

Output Voltage Range (120V +/- 10%); On Battery Output Voltage Range (120V +/- 5%); Output Waveform Line Mode (filtered

sinewave); Output Waveform Battery Mode (PWM sine wave); AC Surge Suppression (exceeds IEEE 587 Cat. A & B standards);

AC Noise Attenuation (>40 dB); AC TVSS Protection Modes (H to N, H to G, N to G).

FCC Radio/TV Interference Notice

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction

manual, may cause interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference using one or more of the following measures: reorient

or relocate the receiving antenna; increase the separation between the equipment and receiver; connect the equipment into an outlet

on a circuit different from that which the receiver is connected; consult the dealer or an experienced radio/television technician for help.

The user must use shielded cables and connectors with this product. Any changes or modifications to this product not expressly

approved by the party responsible for compliance could void the user's authority to operate the equipment.

200007222 Smart 450 RT Owners Manual [120 Volt].p65 9/7/00, 5:16 PM8

Inhaltsverzeichnis

Andere Tripp Lite UPS Handbücher

Tripp Lite

Tripp Lite BCINTERNET500 Bedienungsanleitung

Tripp Lite

Tripp Lite AVRX Series Bedienungsanleitung

Tripp Lite

Tripp Lite SMART1050SLTAA Bedienungsanleitung

Tripp Lite

Tripp Lite OMNISMART1400HG Montage- und Bedienungsanleitung

Tripp Lite

Tripp Lite SM750XLNAFTA Bedienungsanleitung

Tripp Lite

Tripp Lite OmniPro 500 Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro XL INT Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU80KX Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU6000RT3UHV Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU1000XL Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline Single-Phase 10kVA Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro SMART2200RMXL2UP Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU750XL Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro Series Bedienungsanleitung

Tripp Lite

Tripp Lite INTERNET550U Bedienungsanleitung

Tripp Lite

Tripp Lite OmniSmart OMNIVS800 Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU1500LCD1U Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro AGSM152DRTi2U Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro Rackmount SMX3000XLRT2U Konfigurationshandbuch

Tripp Lite

Tripp Lite OmniSmart OMNI300NAFTA Bedienungsanleitung

Tripp Lite

Tripp Lite SMART1200LCD Bedienungsanleitung

Tripp Lite

Tripp Lite AGSM5000Y3U3I Bedienungsanleitung

Tripp Lite

Tripp Lite SMART1000LCDU Bedienungsanleitung

Tripp Lite

Tripp Lite OmniSmart OMNI1500LCD Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung