Tripp Lite SmartPro XL INT Bedienungsanleitung

Quick Installation: p. 3 - 4

Basic Operation: p. 5 - 7

Storage & Service: p. 7

Specifications: p. 7

Safety: p. 2

Warranty & Insurance: p. 6

1111W.35thStreet

Chicago, IL 60609 USA

CustomerSupport:(773)869-1234

www.tripplite.com

Owner'sManual

SmartPro®INT

SmartPro®XL INT

2200-3000 VA

Intelligent,Line-Interactive

UPSSystems (230V)

ESPAÑOL: p. 8

FRANÇAIS:p.15

DEUTSCH:p.22

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:13 AM1

This manual contains important instructions and warnings that should be

followed during the installation, operation and storage of all Tripp Lite UPS

Systems.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, dust or

direct sunlight.

• For best performance, keep the indoor temperature between 0° C and

40° C (between 32° F and 104° F).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS to a properly grounded AC power outlet. Do not

modify the UPS's plug. Do not use adapters that eliminate the UPS's

connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void

your warranty.

• If you are connecting your UPS to a motor-powered AC generator,

the generator must provide clean, filtered computer-grade output.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support applications in

which a malfunction or failure of a Tripp Lite UPS System could cause

failure or significantly alter the performance of a life-support device.

• Do not connect surge suppressors to the output of your UPS. This may

damage your UPS and will void both the surge suppressor and UPS

warranties.

Battery Warnings

• Your UPS does not require routine maintenance. Do not open your

UPS for any reason. There are no user-serviceable parts inside.

• Battery replacement must be performed by qualified service personnel.

Because the batteries present a risk of electrical shock and burn from

high short-circuit current, qualified service personnel should observe

proper precautions: Unplug and turn off the UPS before performing

battery replacement. Use tools with insulated handles and replace the

existing batteries with the same number and type of new batteries

(Sealed Lead-Acid). Do not open the batteries. Do not short or bridge

the battery terminals with any object.

• The UPS batteries are recyclable. Refer to local codes for disposal

requirements. Do not dispose of the batteries in a fire.

• When adding external batteries, connect only Tripp Lite battery packs

of the correct voltage and type. Your UPS's External Battery Connector

should match the color of the connector of any battery pack you want

to connect.

Safety

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:13 AM2

Quick Installation

Connect the UPS to an electrical

outlet and a computer to the

UPS.

• Unplugthe computer’spower cord fromboth your AC

outletand the computer’sAC input.

• Insert the female plug of the computer’s cord (B) into

your UPS’s AC input. Insert the male plug of your

computer’scord into your ACoutlet.

• Insert the female plug of the power cord that came with

your UPS (A) into the computer’s AC input. Insert the

UPS cord’s male plug into any of your UPS’s female

outputreceptacles.

Plug additional computers and

equipment into your UPS.

YourUPS isdesigned to supportonly computerequipment.

Youwill overload your UPSif you connecthousehold

appliances, laser printers or surge suppressors.

Cords and receptacle adapters are available from

Tripp Lite to accommodate most outlet configurations.

If rewiring is necessary, refer to the Wire Color-Code

Chart in the Specifications section.

A B

SEE MANUAL

Turn your UPS ON.

• Set the System Enable Switch (DIP

Switch #4, UPS back panel) to the

“ENABLE”(UP)position.

(See Figure 1)

This switch activates the battery charger and

microprocessor.

The “ ” light will flash until you engage the

ON/Standby Switch to activate the “ON”

mode.

• EngagethemomentaryON/Standby

Switch (UPS front panel) and release it

to activate the “ON” mode and supply

power to the UPS receptacles.

(See Figure 2)

Figure 2 - ON/Standby Switch

Figure 1 DIP Switch #4

(SystemEnableSwitch)

ENABLE

DISABLE

DB9 Port Connection (Optional) On Next Page . . .

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:13 AM3

DB9 Port Connection

–Optional–*

Using the grey or tan Tripp Lite cable

that came with your UPS, connect

your primary server’s DB9 port to the

single DB9 port labeled “LAN 4.1”

(which provides complete intelligent

RS-232 communications).**

* Serial port connections are optional. Your UPS

will function properly without these

connections.

* * The “LAN 4.1” DB9 port is always enabled

and is not controlled by the LAN Interface DIP

Switches.

If you have additional

computers:

Connect them to the DB9 ports

labeled “LAN 2.2” (which provide

basic, contact-closure shutdown

capabilities) using the black cables

that came with your UPS.

Set their corresponding LAN Interface

DIP Switches to the ACTIVATE

(DOWN) position. See diagram for

which switch controls which port.***

*** If you do not connect a computer to either of

the “LAN 2.2” DB9 ports, set their

corresponding LAN Interface DIP Switches to

the DEACTIVATE (UP) position.

Note: DIP Switch #3 has no function.

2a. Back Panel

Load software and run the installation program

appropriate for your operating system.

2b. Back Panel

DIP Switches #2 & #1

(LanInterfaceSwitches)

DEACTIVATE

ACTIVATE

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:13 AM4

Basic Operation

Switches

System Enable Switch (DIP Switch #4)

This switch is on the back panel in the set of 4 switches next to

the UPS’s DB9 ports. It activates the battery charger and intelligent

microprocessor. Always leave it in the “ENABLE” (UP) position

when your UPS is plugged in. Set the switch to “DISABLE” (DOWN)

only if you store or ship your UPS (to reduce battery drain).

Note: the “ ” light will flash until you engage the ON/Standby Switch to activate the

“ON” mode (power ON at the UPS receptacles).

ON/Standby Switch

This momentary switch on the front panel controls power to the

UPS receptacles. Engage it momentarily and release it to toggle

between the “ON” mode (power ON at the UPS receptacles) and

“Standby” mode (power OFF at the UPS receptacles).

Mute/Test Switch

Use this momentary switch on the front panel to do two things:

Silence the UPS On Battery alarm

Engage this switch and release it to silence the UPS On Battery

alarm, a series of short beeps that sounds intermittantly when

the UPS is providing AC power from battery. Note: when the

battery is nearly depleted, the Low Battery alarm, a continuous

beep that cannot be silenced, will alert you to immediately shut

down connected equipment.

Test your UPS’s battery charge

Leave your connected equipment ON. With your UPS plugged in

and completely turned ON, engage this switch; hold it there for

5 seconds and release it. You will hear a series of short beeps as

the UPS momentarily switches to battery to test its charge. The

“” light will turn ON and the alarm (a long, continuous beep)

will sound if your UPS fails a self-test and/or the UPS battery is

less than fully charged. If this occurs, let the UPS charge for 12

hours and perform a second self-test. If the light continues to stay

on, contact Tripp Lite for service. CAUTION: Do not unplug your

UPS to test its batteries. This will remove safe electrical grounding

and may introduce a damaging surge into your network connections.

Indicator Lights

Light descriptions apply when the UPS is plugged into a wall outlet and turned ON.

This green light will shine constantly to indicate AC power is

available at the receptacles. It will flash to indicate AC power is

not available. (See “System Enable Switch” and “On/Standby

Switch” descriptions above.)

This multi-colored light displays 7 separate UPS battery charge

conditions. It will turn from red (low) to yellow (medium) to green

(full) to show you the level of battery charge. If the light is

constant, your UPS is operating from line power, and the battery is

charging. If the light is flashing, your UPS is operating from battery

power, and the battery is discharging. When the light flashes red,

close any files you are working on and shut down your computer.

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:13 AM5

Other UPS Features

AC Receptacles

The receptacles provide your connected equipment with AC line

power during normal operation and battery power during black-

outs and brownouts. They also protect your equipment against

damaging surges and line noise. You can remotely reboot con-

nected equipment by turning all of the receptacles OFF and ON

at once using Tripp Lite UPS software. Select models, however,

feature a unique “Remote Reboot Outlet” (identified on the back

panel of your UPS) which allows you to use Tripp Lite UPS software

to remotely reboot equipment connected to this outlet without

interrupting power to equipment connected to the other outlets.

See software instructions for details.

RS-232 Port

This port, labeled "LAN 4.1" on the UPS, connects your UPS to a

workstation or server. Use with Tripp Lite software and cabling to

monitor and manage network power and automatically save open

files and shut down equipment during a blackout. This port uses

RS-232 communications to transmit UPS and power conditions

(Pin 7 = Transmit; Pin 8 = Common; Pin 9 = Receive). Contact Tripp

Lite Customer Support for more information and a list of available

SNMP, network management and connectivity products.

Contact Closure Ports

These ports, labeled "LAN 2.2" on the UPS, are also used to

connect your UPS to a workstation or server. Use with Tripp Lite

software and cabling to automatically save open files and shut

down equipment during a blackout. This port uses contact-

closure signals to indicate line-fail and low-battery status.

Contact Tripp Lite Customer Support for more information.

Note: constant power is available at the Remote Reboot Outlet (and all other outlets)

unless controlled through Tripp Lite UPS software.

Whenever your UPS is automatically correcting high or low AC

line voltage, this green light will turn ON and the UPS will gently

click. The more the UPS has to correct voltage, the more the

green light will turn ON and the more the UPS will click. These

are both normal, automatic operations of your UPS, and no action

is required on your part.

This red light will turn ON if your UPS fails a self-test and/or the

UPS battery is less than fully charged. Let the UPS charge for 12

hours and perform a second self-test. If the light continues to

stay on, contact Tripp Lite for service.

This multi-colored light displays 4 separate UPS load conditions.

It will turn from green (low) to yellow (medium) to red (high) as

you connect equipment to show you the load level your UPS is

supporting. When the light is red, your UPS is supporting a load

above 85% of its capacity. If the red light begins flashing, then

your UPS is severely overloaded. Remove overload immediately

until light stops flashing.

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:13 AM6

Specifications

Storage & Service

Storage

Turn your UPS OFF: first engage the ON/Standby Switch and release it to place

your UPS in the “Standby” mode, then move the System Enable Switch to the

"DISABLE" (DOWN) position to prevent battery drain, then disconnect the UPS

power cord from the wall outlet. If you plan on storing your UPS for an extended

period of time, recharge the UPS batteries once every three months. Follow

steps #1 and #3 in the Quick Installation section and allow the UPS to charge

from 4 to 6 hours. If you leave your UPS batteries discharged for an extended

period of time, they will suffer permanent loss of capacity.

Service

If returning your UPS for service, contact your local Tripp Lite dealer or

distributor. They will refer you to a service center. Please carefully pack the UPS

using the ORIGINAL PACKING MATERIAL that came with the unit. Enclose a

letter describing the symptoms of the problem. If the UPS is within the 2 year

warranty period, enclose a copy of your sales receipt.

Smart INT 2200 Smart INT 3000

Output Capacity (VA/Watts): 2200/1700 3000/2400

Battery Runtime (Half Load/

Full Load) Minutes: 27+/11+* 23+/7+*

Battery Recharge Time: 2-4 hrs. 2-4 hrs.

Approvals: UL, CE UL, CE

* Battery Runtime for this model can be increased with the addition of optional external battery packs.

Input Voltage (230V); Input Frequency (50/60 Hz, Auto-Selecting); On-Line Input Voltage Range (166-276 volts); Voltage-Regulated Output

Voltage Range (230V +8%/-15%); On-Battery Output Voltage Range (230V ± 5%); Output Waveform Line Mode (filtered sinewave); Output

Waveform Battery Mode (PWM sine wave); AC Surge Suppression (exceeds IEEE 587 Cat. A & B standards); AC Noise Attenuation

(>40 dB); AC TVSS Protection Modes (H to N, H to G, N to G).

Wire Color-Code Chart

The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change.

External Battery Connector

Use to connect additional Tripp Lite battery packs for additional

runtime. Refer to the label next to the connector for the appro-

priate Tripp Lite battery pack to connect. Refer to instructions

available with the battery pack for complete connection informa-

tion and safety warnings.

Wire Color Wire 1 Wire 2 Wire 3

American Black White Green

European Brown Blue Green/Yellow

Wire Reference Wire 1 Wire 2 Wire 3

American Line 1 Neutral Ground

European Line 1 Line 2 or Neutral Ground

EURO

Brown

Blue

Green/

Yellow

Black

White

Green

AMER

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:13 AM7

Derechos de autor 2000 Tripp Lite. Se reservan todos los derechos. SmartPro®es una marca comercial registrada de Tripp Lite.

Instalación rápida: p. 10 - 11

Operación básica: p. 12 - 14

Almacenamiento y servicio: p. 14

Especificaciones: p. 14

Seguridad: p. 9

Warranty & Insurance: p. 6

1111W.35thStreet

Chicago, IL 60609 USA

DepartamentodeAsistenciaalCliente:

(773)869-1234

www.tripplite.com

Manual del usuario

SmartPro®INT

SmartPro®XL INT

2200-3000VA

SistemasUPSinteligentes,

interactivos con la línea (230V)

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:13 AM8

Este manual contiene instrucciones y advertencias importantes que se deben

observar durante la instalación, operación y almacenamiento de todos los sistemas

UPS de Tripp Lite.

Advertencias sobre la ubicación del UPS

• Instale el UPS en el interior, alejado de lugares excesivamente húmedos o

calientes, del polvo y de la luz solar directa.

• Para obtener el mejor rendimiento, mantenga la temperatura en el interior

entre 0º C y 40º C (entre 32º F y 104º F).

• Asegúrese de que haya suficiente espacio alrededor del sistema UPS para

permitir una ventilación adecuada.

Advertencias sobre la conexión del UPS

• Conecte el UPS a un tomacorriente de CA conectado adecuadamente a tierra.

No trate de modificar el enchufe del UPS. No utilice adaptadores para

eliminar la conexión a tierra del UPS.

• No conecte el sistema UPS en sí mismo, pues le causaría daños y se

anularía la garantía.

• Si no va a conectar el sistema UPS a un generador alimentado por CA, el

generador debe proporcionar una salida limpia y filtrada, idónea para

computadoras.

Advertencias sobre las conexiones del equipo

• No utilice los sistemas UPS de Tripp Lite para aplicaciones de sustentación

de la vida en las cuales el mal funcionamiento o la falla del sistema UPS de

Tripp Lite pudiese ocasionar una falla o alterar significativamente el

rendimiento del dispositivo de sustentación de la vida.

• No conecte supresores de sobrevoltaje a la salida del UPS. Si lo hace podría

causar daños al UPS y anular las garantías del supresor de sobrevoltaje y del

sistema UPS.

Advertenciassobrela batería

• El sistema UPS no requiere mantenimiento de rutina. No abra el sistema

UPS por ninguna razón. El sistema no contiene en su interior piezas a las

que el usuario pueda dar servicio.

• Solamente personal de servicio calificado debe realizar el reemplazo de la

batería. Debido a que las baterías representan un riesgo de descargas

eléctricas y quemaduras por corriente alta de cortocircuito, el personal de

servicio calificado debe observar las precauciones adecuadas. Desenchufe y

apague el sistema UPS antes de reemplazar la batería. Utilice herramientas

con mangos aislados y reemplace las baterías existentes con baterías nuevas

del mismo número y tipo (selladas, de plomo ácido). No abra las baterías. No

produzca un cortocircuito ni establezca un puente entre los terminales de la

batería y cualquier otro objeto.

• Las baterías del UPS se pueden reciclar. Consulte los códigos locales para

ver los requisitos de eliminación de las baterías. No coloque las baterías en

el fuego.

• Cuando añada baterías externas, sólo conecte bloques de baterías de

Tripp Lite del voltaje y tipo correctos. El conector de la batería externa del

UPS debe coincidir con el color del conector de cualquier bloque de baterías

que desee conectar.

Seguridad:

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:13 AM9

Instalación Rápida

Conecte el UPS a un tomacorriente

eléctrico y una computadora al UPS.

• Desenchufeel cable eléctrico dela computadora tanto

de la salida de CA como de la entrada de CA de la

computadora.

• Introduzca el enchufe hembra del cable de la

computadora (B) en la entrada de CA del UPS.

Introduzca el enchufe macho del cable de la

computadora en la salida de CA.

• Introduzca el enchufe hembra del cable eléctrico que se

incluye con el UPS (A) en la entrada de CA de la

computadora.Introduzca el enchufemacho del cabledel

UPS en cualquiera de los receptáculos de salida

hembra del UPS.

Conecte al UPS las computadoras y

equipo adicionales.

El UPS está diseñado para aceptar sólo equipo de

computación.Si conectaelectrodomésticos,impresoras

láser o supresores de sobrevoltaje al UPS lo

sobrecargará.

TrippLite tiene disponibles cablesy adaptadores de

receptáculos que se ajustan a la mayoría de las

configuraciones de salida. Si es necesario volver a hacer

las conexiones eléctricas, consulte la tabla de

codificación por color de los cables que se encuentra en la

secciónEspecificaciones.

ENCIENDA el UPS.

• Coloqueelconmutador deactivación

del sistema (conmutador DIP N.º4,

panel posterior del UPS) en la

posición“ENABLE”(“ACTIVAR”)

(ARRIBA).

(Vea la Figura 1)

El conmutador activa el cargador de baterías

y el microprocesador.

La luz “ ” destellará hasta que embrague

el conmutador ON/Standbay

(ENCENDIDO/Pausa) para activar el modo

“ON” (ENCENDIDO”).

• Embragueelconmutadormomentáneo

ON/Standby (panel frontal del UPS) y

libérelo para activar el modo “ON” y

suministrar energía a los receptáculos

del UPS.

(Vea la Figura 2)

A B

SEE MANUAL

Figure 2 - ON/Standby Switch

ConexiónalpuertoDB9(opcional).Enlasiguientepágina...

Figura 1 Conmutador DIP N.°4

(Conmutador de

activación del sistema)

ACTIVAR

Figura 2

9905248 DON'T ARCHIVE!!! 2200-3000 VA 230V SmartPro OM.p65 6/20/00, 10:14 AM10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Tripp Lite UPS Handbücher

Tripp Lite

Tripp Lite SmartOnline 220/230/240V Input/Output Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU16KRT Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline 220/230/240V Input/Output Bedienungsanleitung

Tripp Lite

Tripp Lite OmniSmart OMNIVS800 Bedienungsanleitung

Tripp Lite

Tripp Lite AGOM5516 Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU6000RT4UHVHW Installationsanleitung

Tripp Lite

Tripp Lite SmartPro VS SMART2200VS Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro SMART1000RM2U Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline Bedienungsanleitung

Tripp Lite

Tripp Lite OmniSmart & SmartPro USB Bedienungsanleitung

Tripp Lite

Tripp Lite Internet Office & BC Personal UPS System Bedienungsanleitung

Tripp Lite

Tripp Lite SMART700DVA Bedienungsanleitung

Tripp Lite

Tripp Lite BC800U Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline Single-Phase 10kVA Bedienungsanleitung

Tripp Lite

Tripp Lite ECO-UPS ECO650LCD Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU10000RT3U Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU3000RTXL2U Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro SLT SMX1050SLT Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro SMART1500RM2U Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU80K Bedienungsanleitung

Tripp Lite

Tripp Lite OmniPro 675 Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU6000RT3UHV Bedienungsanleitung

Tripp Lite

Tripp Lite G1010USB Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline 3-Phase 30kVA Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung