Triton 96 Series Bedienungsanleitung

96XX
EMV CARD READER
FIELD INSTALLATION
GUIDE
VERSION 2.0
TDN 07007-00005B 09/04
COPYRIGHT NOTICE
Copyright © Delaware Capital Formation, Inc., 2001,2004. All rights reserved. No part of this publica-
tion may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
human or computer language, in any form, by any means whatsoever, without the express written per-
mission of Triton Systems of Delaware, Inc. DOVER and the DOVER logo are registered trademarks
of Delaware Capital Formation, Inc., a wholly-owned subsidiary of Dover Corporation.
CORPORATE HEADQUARTERS: RMA(RETURN MATERIALAUTHORIZATION)
RETURN ADDRESS:
522 E. Railroad Street 21405 B Street
Long Beach, MS 39560 Long Beach, MS 39560
PHONE: (228) 868-1317
FAX: (228) 868-0437

96XX CASH DISPENSER
EMV CARD READER - FIELD INSTALLATION GUIDE
2
INTRODUCTION
This Installation Guide provides instructions for in-
stalling the EMV Card Reader, modified paper roll
bracket and grounding straps.
PART SUPPLIES/REQUIRED TOOLS
Thefollowingtableliststhe parts suppliedin theEMV
Card Reader Upgrade Kit:
INSTALLATION PROCEDURE
1. Unlock and open the ATM control panel.
2. Turn the ATM power switch (on the right side of
the card cage module) to the OFF (0) position.
3. Removethe printerpaperroll.Refer toapplicable
operation manual for procedure.
4. [Optional] Unlock and open the fascia panel.
5. [Optional] Whileholdingthe controlpanelfirmly,
twistthe pneumaticpistonarm inacounter-clock-
wise direction to unscrew it from the bracket, as
shown.
tiKedargpUredaeRdraCVME )02000-00260N/P(
170000-26110REDAERDRACVME
198000-08010 DAUQ-OT-REDAERDRAC,ELBAC DRAOBTROP
231000-02190GNIDNUORG,ELBAC
174000-110
30TEKCARBROSNESREPAP
240000-12320RENETSAFPANSNOLYN
189100-11030TEKCARBLLORREPAP
270000-30320NOLYN,REHSAW
194000-4
5020"8/3X23-8#,WERCS
100000-81320DEDAERHT,FFODNATS
110000-32320DEDAERHT,TRESNI
101000-03010ETIRREF
290000-27030EVI
SEHDA,TIUDNAP,PILCELBAC
144000-00690DRAOBTROPLAIRESDAUQ
251000-27030HCNI-6,PARWYT
200300-45020DAEHXEH"4/1X23-6
#,WERCS
1B50000-70070EDIUGNOITALLATSNIDLEIF
SLOOTDEDNEMMOCER
REVIRDWERCSSPILLIHPMUIDEM
-61/7RO,TEKCOSHCNI-61/7HTIWHCNERWTEKCOS REVIRDTUNHCNI
)SPARWYTGNITTUCROF(SPINSROSRETTUCERIW
CAUTION!
Ifyou needmoreroom toworkon thecontrol panel
youmay disconnect thepneumatic armand lower
the panel to provide more work space, as de-
scribedin thefollowingoptional steps.Beadvised
thatthis placesadditional stresson the panel,and
makes it vulnerable to cracking or splitting!
DO NOT BEND OR FLEX THE PANEL DURING
PERFORMANCE OF THE INSTALLATION PRO-
CEDURE!

96XX CASH DISPENSER
EMV CARD READER - FIELD INSTALLATION GUIDE
3
6. [Optional] Lower thecontrolpanelso thatit rests
on the top edge of the fascia panel.
7. Use a screwdriver to remove the screws that se-
cure the two cable clips to the printer bracket.
8. Cut the ty wrap that secures the printer power,
reset and paper low sensor cables to the left
printer bracket cable clip. Note how the cables
are ty-wrapped to the clip: you will use a new
ty wrap to reconnect the cables to the clip in
a later step.
9. Cut the ty wrap that secures the printer power
and reset cables to the right cable clip. Note
how the cables are ty-wrapped to the clip: you
will use a new ty wrap to reconnect the cables
to the clip in a later step.
10. Disconnect the cable connectors at J3 (Printer)
and J5 (Printer-Reset) on the keypad board.

96XX CASH DISPENSER
EMV CARD READER - FIELD INSTALLATION GUIDE
4
11. Remove the ribbon cable from between the ad-
hesive cable clips.
12. Disconnect the low paper sensor cable at con-
nectorJ11ontheprintercontrol board.This cable
is connected to the low paper sensor on the pa-
per roll bracket.
14. Use a socket wrench to loosen the bolt on the
pneumatic piston bracket.
13. Disconnect the existing low paper sensor by re-
moving the sensor bracket screws with a phillips
screwdriver. Retain screws and set component
aside. The sensor will be remounted on the new
paper support bracket.
NOTE
If you have an old sensor bracket shown in Figure
1, the bracket will be replaced with the bracket in-
cluded with the kit (Figure 2). Instructions for re-
moving and reinstalling the sensor are at the end
of this manual.
If you have the bracket type shown in Figure 3,
you will simply remount the bracket (w/sensor) on
to the new paper support bracket.
Figure 1
Figure 3
Low Paper
Bracket Arm
Upper slot
Figure 2

96XX CASH DISPENSER
EMV CARD READER - FIELD INSTALLATION GUIDE
5
15. Usea screwdrivertoloosen (donot remove!)the
two screws at the top of the printer bracket.
16. Remove the two screws that attach the paper
bracket to the printer bracket.
17. Move the disconnected cables out of the way as
needed. Lift the printer bracket slightly and slide
the paper bracket from beneath the lower edge
ofthe printerbracket. Removethepaperbracket.
18. Slide new paper bracket underneath lower edge
of printer bracket.

96XX CASH DISPENSER
EMV CARD READER - FIELD INSTALLATION GUIDE
6
21. Connect the low paper sensor cable at connec-
tor J11 on the printer control board. This cable is
connected to the paper low sensor on the paper
roll bracket.
22. Ty wrap the printer power, printer reset and pa-
per low sensor cables to the left cable clip.
23. Tywrapthe printerpower andprinterreset cables
to the right cable clip.
20. Reinstall thelowpapersensorbracket previously
removed to the paper support bracket
19. Attach the new paper bracket to the printer
bracket, using the screws that were removed
previously.

96XX CASH DISPENSER
EMV CARD READER - FIELD INSTALLATION GUIDE
7
24. Attachthetwocable clips(withty-wrapped cabled
attached) to the printer bracket holes, using the
screws that were removed previously.
25. Use a screwdriver to tighten the upper printer
bracket screws that were loosened previously.
26. Use a socket wrench to tighten the pneumatic
arm bracket bolt (loosened in an earlier step).
27. Place two adhesive cable clips on new bracket
(for ribbon cable).
28. Place ribbon cable through two adhesive cable
clips.

96XX CASH DISPENSER
EMV CARD READER - FIELD INSTALLATION GUIDE
8
31. Remove the four mounting screws from the ex-
isting card reader.
32. Removetheexisting cardreaderthroughthefront
of the ATM control panel.
33. Note grounding wire on EMV card reader. If nec-
essary, remove the screw that secures one end
of the card reader's grounding wire to the body
of the card reader. Replace the screw.
30. Removedata cablefrom theexisting cardreader
and from J4 on the keypad board.
29. Reconnect J3 (Printer) and J5 (Printer Reset)
cables to the keypad board.

96XX CASH DISPENSER
EMV CARD READER - FIELD INSTALLATION GUIDE
9
35. Secure the card reader in place using the four
mounting screws that were removed previously.
36. Connect a grounding strap between rear cabinet
bolt and card cage screw.
34. InsertEMV cardreaderthrough frontofATMcon-
trol panel. 37. Connectagrounding straptothe leftcontrol panel
hinge bolt (near the car reader).
38. Install the mounting post for the card reader’s
ESD module. First, locate the panel boss, below
and immediately to the right of the card reader.
Ensure there is no dust, dirt or other foreign
material in the panel boss hole. Place the pro-
vided threaded insert into the panel boss. Im-
portant: Turn the insert so that the non-
threaded end is inserted into the panel boss
hole FIRST.
Apply firm pressure with the tip of a screwdriver
or other tool to press the insert into the boss.
The insert should fit snugly and should be flush
with the surface of the boss.

96XX CASH DISPENSER
EMV CARD READER - FIELD INSTALLATION GUIDE
10
40. Placethecard readergroundingwireand ground-
ing strap lugs onto the ESD module mounting
hole and secure the ESD module and grounding
wires to the standoff with a single screw.
41. Connect cable from ESD module to card reader.
Note: orange wire in connector should be on the
left.
39. Use a nutdriver to screw the threaded standoff
into the insert that was installed in the previous
step.
Inhaltsverzeichnis
Andere Triton Kartenleser Handbücher
Beliebte Kartenleser Handbücher anderer Marken

Rosslare
Rosslare DR-6255 Bedienungsanleitung

Lindy
Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler
Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls
Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS
ACS ACR122L Bedienungsanleitung

Secukey
Secukey S2-MF Bedienungsanleitung












