Trotec PCPS 10-16V Bedienungsanleitung
TRT-BA-PCPS10-16V-PCPS11-16V-TC-001-EN
PCPS 10-16V / PCPS 11-16V
EN
OPERATING MANUAL
1 EN
Operating manual – PCPS 10-16V / PCPS 11-16V
Table of contents
Notes regarding the operating manual.................................1
Safety .....................................................................................1
Information about the device................................................5
Transport and storage...........................................................7
Start-up..................................................................................8
Operation .............................................................................11
Available accessories..........................................................13
Errors and faults..................................................................13
Maintenance ........................................................................14
Disposal ...............................................................................15
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Notice
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
Wear ear protection
Information marked with this symbol indicates that you
should wear hearing protection.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
PCPS 10-16V
PCPS 11-16V
https://hub.trotec.com/?id=41512
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Observe all the safety warnings, instructions,
illustrations and technical data provided with this
power tool.
Failure to follow the instructions below may result in
electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
The term power tool used in the safety warnings refers to both
mains-operated and battery-powered electric tools (with/
without power cable).
EN 2
Operating manual – PCPS 10-16V / PCPS 11-16V
General Power Tool Safety Warnings – Work area
safety
•Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
•Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
•Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
General Power Tool Safety Warnings – Electrical
safety
•Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
•Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
•Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
•Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep the cord
away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric
shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
•If operating a power tool in a damp location is
unavoidable, use a residual current device(RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
General Power Tool Safety Warnings – Personal
safety
•Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
•Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
•Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
•Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
•Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
•If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. The use of a dust
extraction system may reduce dust-related hazards.
•Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
General Power Tool Safety Warnings – Power tool
use and care
•Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
•Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
•Disconnect the plug from the power source and / or
the battery pack, if detachable, from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
•Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
3 EN
Operating manual – PCPS 10-16V / PCPS 11-16V
•Maintain power tools and accessories carefully. Check
for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
•Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
•Keep handles and gripping surfaces dry, clean and
free from oil and grease. Slippery handles and gripping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
General Power Tool Safety Warnings – Battery tool
use and care
•Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
•Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
•When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
•Under abusive conditions, liquid may be ejected from
the battery. Avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
•Do not use a damaged or modified battery. Damaged or
modified batteries can behave unexpectedly and lead to
fires, explosions or injuries.
•Do not expose a battery to fire or excessively high
temperatures. Exposure to fire or temperatures above
130°C (265°F) may cause an explosion.
•Follow all the instructions for charging and never
charge the battery or the cordless tool outside the
temperature range specified in the operating
instructions. Incorrect charging or charging outside of the
permissible temperature range can destroy the battery and
increase the risk of fire.
General Power Tool Safety Warnings – Service
•Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
•Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorized service providers.
EN 4
Operating manual – PCPS 10-16V / PCPS 11-16V
Intended use
Only use the device PCPS 10-16V:
• for inflating car tyres, bicycle tyres, inflatable toys, sports
equipment and beach items
• measuring the current pressure level of an inflatable object
whilst adhering to the technical data.
Info
Please note that the pressure gauge is not calibrated.
Only use the device PCPS 11-16V:
• for inflating and deflating common inflatables with a large
volume such as air mattresses, swimming pools, rubber
dinghies or camping equipment
whilst adhering to the technical data.
We recommend using the power tool with original Trotec
accessories.
Improper use
The device PCPS 11-16V is not intended for inflating bicycle or
car tyres.
Personnel qualifications
People who use this device must:
• have read and understood the operating manual, especially
the Safety chapter.
Personal protective equipment
Wear hearing protection.
Excessive noise can lead to hearing loss.
Residual risks
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket and the battery from the device!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Warning of explosive substances
Do not expose the battery to temperatures above 45
°C! Do not let the battery come into contact with water
or fire! Avoid direct sunlight and moisture. There is a
risk of explosion!
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Caution
Keep a sufficient distance from heat sources.
Notice
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Notice
The device is not suitable for continuous operation. To
prevent overheating, the device must not be used non-
stop for more than 10minutes(PCPS 10-16V) or
20minutes(PCPS 11-16V).
Should the device be overheating nonetheless, remove
the battery.
Allow the device to cool down sufficiently before
switching it back on.
5 EN
Operating manual – PCPS 10-16V / PCPS 11-16V
Information about the device
Device description
The cordless compressor PCPS 10-16V is suited for blowing up
bicycle tyres, car tyres as well as inflatables toys or sports
equipment such as footballs.
The device is equipped with an integrated pressure gauge.
Upon reaching the desired pressure value, the device will be
switched off automatically.
The cordless air pump PCPS 11-16V is suited for inflating and
deflating inflatable products with a large volume such as air
mattresses or rubber dinghies.
Device depiction
Cordless compressor PCPS 10-16V
1
3
2
4
3
9
8
7
6
5
No. Designation
1 Mount for valve adapters
2 Handle
3 Air inlet
4 Mount for compressed-air hose
5 Control panel
6 Battery holder
7 On/off switch
8 LED work lamp
9 Union nut
Cordless air pump PCPS 11-16V
10
11
15
14
13
12
No. Designation
10 Air inlet (deflating)
11 Handle
12 Battery holder
13 On/off switch
14 LED work lamp
15 Air outlet (inflating)
EN 6
Operating manual – PCPS 10-16V / PCPS 11-16V
Accessories
16
18
17
24a
24
19
20
21
22
23
No. Designation
16 Quick charger
17 Nozzle attachments for air pump
18 Compressed-air hose with threaded connector
19 Presta valve adapter
20 Dunlop valve adapter
21 Ball needle
22 Universal adapter, short (2pieces)
23 Universal adapter, long
24 Battery
24a Battery level indication
Scope of delivery
• 1 x Cordless compressor PCPS 10-16V
• 1 x Cordless air pump PCPS 11-16V
• 1 x Rechargeable battery
• 1 x Quick charger
• 1x Compressed-air hose with threaded connector
• 1x Dunlop valve adapter
• 1x Presta valve adapter
• 1x Ball needle
• 1x Universal plastic adapter with 3nozzle attachments for
air pump
• 2x Universal adapter, short
• 1x Universal adapter, long
• 1 x Transport case
• 1x Manual
Technical data
Parameter Value
Model PCPS10-16V PCPS11-16V
Nominal voltage 16 V 16 V
Max. pressure 7bar (100psi) -
Max. air flow rate - 45 m³/h
Weight 1.0 kg 0.7 kg
Battery PCPS16V DC
Type Li-ion
Nominal voltage 16 V
Capacity 2.0Ah
Quick charger PCPS16V AC
Input
Nominal voltage 220 – 240V/ 50Hz
Power consumption 56 W
Output
Nominal voltage 16.8 V
Charging current 2.5 A
Charging time approx. 1h
Cable length 1.5 m
Protection class II /
Vibration information according to EN60745
Vibration emission
valueah
Uncertainty K
2.6 m/s²
1.5 m/s²
2.6 m/s²
1.5 m/s²
Sound values according to EN60745
Sound pressure
level LpA
84 dB(A) 80 dB(A)
Sound power level
LWA
95 dB(A) 91 dB(A)
Uncertainty KWA 3 dB(A) 3 dB(A)
Wear hearing protection.
Excessive noise can lead to hearing loss.
7 EN
Operating manual – PCPS 10-16V / PCPS 11-16V
Information on noise and vibration:
• The vibration level specified in these instructions was
determined by means of a measuring method standardized
in EN60745 and can be used for a device comparison. The
specified vibration emission value may also be used for a
preliminary assessment of the exposure.
• The vibration level will change depending on the
application of the power tool and may in some cases differ
from the value specified in these instructions. The vibration
load may be underestimated if the power tool is used
regularly in such a way. For a precise estimation of the
vibration load during a certain work period, it is also
important to consider the periods during which the device
is switched off, or is running but not actually employed.
This can reduce the vibration load over the entire work
period significantly.
Transport and storage
Notice
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
For transporting the device, use the transport case included in
the scope of delivery in order to protect the device from external
influences.
Before transporting the device, observe the following:
• Switch off the device.
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Allow the device to cool down.
• Remove the battery from the device.
The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:
• The user may transport the batteries by road without any
additional requirements.
• If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
– Only ship batteries if their housing is undamaged.
– Mask open terminals with tape and pack the battery in
a way that it cannot move inside the packaging.
– Please also observe any other national regulations.
Storage
Before storing the device, observe the following:
• Switch off the device.
• Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
• Allow the device to cool down.
• Remove the battery from the device.
• Clean the device as described in the Maintenance chapter.
• For storing the device, use the transport case included in
the scope of delivery in order to protect the device from
external influences.
• Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• ambient temperature below 40 °C
• protected from dust and direct sunlight inside the transport
case
EN 8
Operating manual – PCPS 10-16V / PCPS 11-16V
Start-up
Unpacking the device
• Take the transport case out of the packaging.
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
• Check the contents of the transport case for completeness
and look for damages.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
• Dispose of the packaging material according to the
national regulations.
Charging the battery
Notice
The battery can be damaged in case of improper
charging.
Remove the charger's mains plug before inserting or
removing the battery.
Never charge the battery at ambient temperatures
below 10°C or above 40°C.
The battery is partially charged upon delivery to avoid damage
to the battery caused by a deep discharge.
Prior to initial start-up and when the battery is low (only the red
LED in the battery level indication(24a) is illuminated), the
battery should be charged. To do so, please proceed as follows:
1. Slide the battery(24) into the quick charger(16) upside
down.
26
25
1 h
16
24
2. Insert the mains plug of the quick charger(16) into a
properly fused mains socket.
ðThe red battery LED(26) lights up.
ðCharging requires approx. one hour.
3. Wait until the red battery LED(26) goes off and the green
battery LED(25) lights up.
ðThe battery(24) is fully charged.
4. Hold onto the mains plug while pulling the power cable of
the quick charger(16) out of the mains socket.
ðThe battery(24) and the quick charger(16) may have
become warm during charging.
Allow the battery(24) to cool down to room
temperature.
5. Remove the battery(24) from the quick charger(16).
Inserting the battery
1. Slide the battery(24) onto the device until it locks in place.
27
24
9 EN
Operating manual – PCPS 10-16V / PCPS 11-16V
Removing the battery
1. Detach the battery(24) from the device by pressing and
holding the unlocking button(27; I.) and pulling the battery
off the device (II.).
I.
II.
2. If required, charge the battery(24) as described in the
section Charging the battery.
Checking the battery status
The battery comes with an integrated battery level indication.
The battery status is displayed as follows by the three LEDs of
the battery level indication(24a):
LED colour Meaning
Green – Orange – Red maximum charge / power
Orange – Red medium charge / power
Red weak charge – Recharge the
battery.
1. Press the button(28) on the battery(24).
ðYou can read the battery status from the battery level
indication(24a).
24a
28
Exchanging the valve adapter (cordless compressor)
Depending on the field of application, the following valve
adapters can be connected either directly to the device or via
the optional compressed-air hose(18).
No. Designation Description
19 Presta valve adapter To be used with Presta valves
20 Dunlop valve adapter To be used with Dunlop valves
21 Ball needle To be used with footballs or the
like
22 Universal adapter, short To be used with air mattresses
or the like
23 Universal adapter, long To be used with air mattresses
or the like
Info
We recommend using the cordless compressor with
connected compressed-air hose.
1. Unscrew the union nut(9).
29
30
9
18
2. Insert either the (optional) compressed-air hose(18) with
its connector side(30) or the valve adapter(19, 20, 21, 22,
23) by rotating it clockwise.
3. Retighten the union nut(9).
ðIf you want to use the valve adapter(19, 20, 21, 22, 23)
without compressed-air hose, the valve adapter is now
fully mounted.
ðIf you want to use the valve adapter(19, 20, 21, 22, 23)
with compressed-air hose, please proceed with the
following steps.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Trotec Luftkompressor Handbücher
