True Manufacturing Company TMW-36F-QT-SD Bedienungsanleitung

tmw – true meat well

TRUE MANUFACTURING CO., INC.

2001 East Terra Lane • O’Fallon, Missouri 63366-4434

(636)-240-2400 • FAX (636)-272-2408 • INT'L FAX (636)272-7546 • (800)-325-6152

Parts Department (800)-424-TRUE • Parts Department FAX# (636)-272-9471

Web: www.truemfg.com

TRUE

manufacturing co., inc.INSTALLATION MANUAL

INSTALLATION MANUAL

tmw – true meat well

TMW-36F-QT-SD

TMW-36F-FT-SD

CONGRATULATIONS!

You have just purchased the finest commercial refrigerator

available. You can expect many years of trouble-free operation.

TABLE OF CONTENTS

SAFETY INFORMATION

Safety Precautions 1

Proper Disposal, Connecting Electricity, & Adapter Plugs 2

INSTALLATION

Ownership, Uncrating, & How to Connect to Electricity 3

Wire Gauge Chart 4

Locating and Leveling 4

SETUP

Standard Accessories 5

OPERATION

Startup 6

Mechanical Temperature Controls Sequence of Operation 6

Electronic Temperature Controls Sequence of Operation 10

MAINTENANCE, CARE, CLEANING

Cleaning Condenser Coil 16

Important Warranty Information 17

Stainless Steel Equipment Care and Cleaning 18

WARRANTY

Warranty 19

TRUE

tmw www.truemfg.com

Loss or spoilage of products in your refrigerator/

freezer is not covered by warranty. In addition to

following recommended installation procedures

you must run the refrigerator/freezer 24 hours

prior to usage.

NOTICE TO CUSTOMER

WARNING: Use this appliance for its intended purpose as described in this Owner Manual.

How to Maintain Your True Refrigerator to Receive the Most Efficient and Successful Operation.

You have selected one of the finest commercial refrigeration units made. It is manufactured under strict quality controls with only the best

quality materials available.Your TRUE cooler when properly maintained will give you many years of trouble-free service.

TO LOCATE REFRIGERANT TYPE, SEE SERIAL LABEL INSIDE CABINET. This cabinet may contain fluorinated greenhouse

gas covered by the Kyoto Protocol (please refer to cabinet’s inner label for type and volume, GWP of 134a= 1,300. R404a= 3,800).

FOR HYDROCARBON REFRIGERATION ONLY (R-290) SEE BELOW:

• DANGER - Risk of fire or explosion. Flammable refrigerant used. Do not use mechanical devices to defrost refrigerator. Do not

puncture refrigerant tubing.

• DANGER - Risk of fire or explosion. Flammable refrigerant used. To be repaired only by trained service personnel. Do not puncture

refrigerant tubing.

• CAUTION - Risk of fire or explosion. Flammable refrigerant used. Consult repair manual/owner’s guide before attempting to service

this product. All safety precautions must be followed.

• CAUTION - Risk of fire or explosion. Dispose of properly in accordance with federal or local regulations. Flammable refrigerant used.

• CAUTION - Risk of fire or explosion due to puncture of refrigerant tubing; follow handling instructions carefully. Flammable refrigerant

used.

• CAUTION - Keep clear of obstruction all ventilation openings in the appliance enclosure or in the structure for building-in.

SAFETY INFORMATION

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be

followed, including the following:

• This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used.

• Do not allow children to climb, stand or hang on the shelves

in the refrigerator. They could damage the refrigerator and

seriously injure themselves.

• Do not touch the cold surfaces in the freezer compartment

when hands are damp or wet. Skin may stick to these

extremely cold surfaces.

• Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance. Do not store

explosive substances such as aerosol cans with a flammable

propellant in this appliance.

• Keep fingers out of the “pinch point” areas; clearances between

the doors and between the doors and cabinet are necessarily

small; be careful closing doors when children are in the area.

• Unplug the refrigerator before cleaning and making repairs.

• Setting temperature controls to the 0 position does not

remove power to the light circuit, perimeter heaters, or

evaporator fans.

NOTE: We strongly recommend that any servicing be preformed

by a qualified technician.

TRUE

tmw www.truemfg.com

RISK OF CHILD

ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of the past.

Junked or abandoned refrigerators are still dangerous… even if they

will sit for “just a few days.” If you are getting rid of your old refrigera-

tor, please follow the instructions below to help prevent accidents.

BEFORE YOU THROW AWAY YOUR OLD

REFRIGERATOR OR FREEZER:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb

inside.

APPLIANCE DISPOSAL

When recycling appliance please make sure that the refrigerants are

handled according to local and national codes, requirements and

regulations.

REFRIGERANT DISPOSAL

Your old refrigerator may have a cooling system that uses “Ozone

Depleting” chemicals. If you are throwing away your old refrigerator,

make sure the refrigerant is removed for proper disposal by a quali-

fied service technician. If you intentionally release any refrigerants you

can be subject to fines and imprisonment under provisions of the

environmental regulations.

USE OF EXTENSION CORDS

NEVER USE AN EXTENSION CORD! TRUE will not war-

ranty any refrigerator that has been connected to an extension cord.

REPLACEMENT PARTS

• Component parts shall be replaced with like components.

• Servicing shall be done by authorized service personnel, to

minimize the risk of possible ignition due to incorrect parts or

improper service.

• Lamps must be replaced by identical lamps only.

• If the supply cord is damaged, it must be replaced by a special

cord or assembly available from the manufacturer or its service

agent.

HOW TO CONNECT ELECTRICITY

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR

REMOVE THE GROUND PRONG FROM THE POWER

CORD. FOR PERSONAL SAFETY, THIS APPLIANCE

MUST BE PROPERLY GROUNDED.

The power cord from this appliance is equipped with a grounding

plug which minimizes the possibility of electric shock hazard.

Have the wall outlet and circuit checked by a qualified electrician to

make sure the outlet is properly grounded.

If the outlet is a standard 2-prong outlet, it is your personal respon-

sibility and obligation to have it replaced with the properly grounded

wall outlet.

The refrigerator should always be plugged into it’s own individual

electrical circuit, which has a voltage rating that matches the rating

plate.

This provides the best performance and also prevents overloading

building wiring circuits which could cause a fire hazard from over-

heated wires.

Never unplug your refrigerator by pulling on the power cord. Always

grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become

frayed or otherwise damaged. Do not use a cord that shows cracks

or abrasion damage along its length or at either end.

When removing the refrigerator away from the wall, be careful not

to roll over or damage the power cord.

If supply power cord is damaged it should be replaced with original

equipment manufacture parts. To avoid hazard this should be done

by a qualified service technician.

USE OF ADAPTER PLUGS

NEVER USE AN ADAPTER PLUG! Because of potential safety

hazards under certain conditions, we strongly recommend against the

use of an adapter plug.

The incoming power source to the cabinet including any adapters

used must have the adequate power available and must be properly

grounded. Only adapters listed with UL should be used.

WARNING!DANGER!

NORTH AMERICA USE ONLY!

NEMA plugs

TRUE uses these types of plugs. If you do not have the right outlet

have a certified electrician install the correct power source.

NOTE: International plug configurations vary by voltage and country.

115/60/1

NEMA-5-15R

115/208-230/1

NEMA-14-20R

115/60/1

NEMA-5-20R

208-230/60/1

NEMA-6-15R

TRUE

tmw www.truemfg.com

OWNERSHIP

To ensure that your unit works properly from the first day, it must

be installed properly. We highly recommend a trained refrigeration

mechanic and electrician install your TRUE equipment. The cost of a

professional installation is money well spent.

Before you start to install your TRUE unit, carefully inspect it for

freight damage. If damage is discovered, immediately file a claim with

the delivery freight carrier.

TRUE is not responsible for damage incurred during shipment.

UNCRATING

TOOLS REQUIRED

• Adjustable Wrench

• Phillips Screwdriver

• Level

The following procedure is recommended for uncrating the unit:

A. Remove the outer packaging by pulling tri-wall nails from skid.

Remove (4) cardboard corner pads and dust cover.

B. Inspect for concealed damage. Again, immediately file a claim

with the freight carrier if there is damage.

C. Move your unit as close to the final location as possible

before removing the wooden skid.

NOTE: KEYS FOR COOLERS WITH DOOR LOCKS

ARE LOCATED IN WARRANTY PACKETS.

ELECTRIC INSTALLATION & SAFETY

INFORMATION

• If the supply cord is damaged, it must be replaced by a special

cord or assembly available from the manufacturer or its service

agent.

• Lamps must be replaced by identical lamps only.

• Appliance tested according to the climate classes 5 and 7

temperature and relative humidity.

ELECTRICAL INSTRUCTIONS

A. Before your new unit is connected to a power supply, check the

incoming voltage with a voltmeter. If anything less than 100% of

the rated voltage for operation is noted, correct immediately.

B. All units are equipped with a service cord, and must be

powered at proper operating voltage at all times. Refer to

cabinet data plate for this voltage.

TRUE RECOMMENDS THAT A SOLE USE CIRCUIT BE

DEDICATED FOR THE UNIT.

WARNING: Compressor warranties are void if compressor burns

out due to low voltage.

WARNING: Power supply cord ground should not be removed!

WARNING: Do not use electrical appliances inside the food

storage compartments of the appliances unless they are of the type

recommended by the manufacturer.

NOTE: To reference wiring diagram, remove front louvered grill,

wiring diagram is positioned on the inside cabinet wall.

INSTALLATION

TRUE

tmw www.truemfg.com

230 Volts Distance In Feet To Center of Load

Amps 20 30 40 50 60 70 80 90 100 120 140 160

5 14 14 14 14 14 14 14 14 14 14 14 14

6 14 14 14 14 14 14 14 14 14 14 14 12

7 14 14 14 14 14 14 14 14 14 14 12 12

8 14 14 14 14 14 14 14 14 14 12 12 12

9 14 14 14 14 14 14 14 14 12 12 12 10

10 14 14 14 14 14 14 14 12 12 12 10 10

12 14 14 14 14 14 14 12 12 12 10 10 10

14 14 14 14 14 14 12 12 12 10 10 10 8

16 14 14 14 14 12 12 12 10 10 10 8 8

18 14 14 14 12 12 12 10 10 10 8 8 8

20 14 14 14 12 10 10 10 10 10 8 8 8

25 14 14 12 12 10 10 10 10 8 8 6 6

30 14 12 12 10 10 10 8 8 8 6 6 6

35 14 12 10 10 10 8 8 8 8 6 6 5

40 14 12 10 10 8 8 8 6 6 6 5 5

50 12 10 10 8 6 6 6 6 6 5 4 4

60 12 10 8 6 6 6 6 6 5 4 4 3

70 10 10 8 6 6 6 5 5 4 4 2 2

80 10 8 8 6 6 5 5 4 4 3 2 2

90 10 8 6 6 5 5 4 4 3 3 1 1

100 10 8 6 6 5 4 4 3 3 2 1 1

115 Volts Distance In Feet To Center of Load

Amps 20 30 40 50 60 70 80 90 100 120 140 160

2 14 14 14 14 14 14 14 14 14 14 14 14

3 14 14 14 14 14 14 14 14 14 14 14 12

4 14 14 14 14 14 14 14 14 14 12 12 12

5 14 14 14 14 14 14 14 12 12 12 10 10

6 14 14 14 14 14 14 12 12 12 10 10 10

7 14 14 14 14 14 12 12 12 10 10 10 8

8 14 14 14 14 12 12 12 10 10 10 8 8

9 14 14 14 12 12 12 10 10 10 8 8 8

10 14 14 14 12 12 10 10 10 10 8 8 8

12 14 14 12 12 10 10 10 8 8 8 8 6

14 14 14 12 10 10 10 8 8 8 6 6 6

16 14 12 12 10 10 8 8 8 8 6 6 6

18 14 12 10 10 8 8 8 8 8 8 8 5

20 14 12 10 10 8 8 8 6 6 6 5 5

25 12 10 10 8 8 6 6 6 6 5 4 4

30 12 10 8 8 6 6 6 6 5 4 4 3

35 10 10 8 6 6 6 5 5 4 4 3 2

40 10 8 8 6 6 5 5 4 4 3 2 2

45 10 8 6 6 6 5 4 4 3 3 2 1

50 10 8 6 6 5 4 4 3 3 2 1 1

WIRE GAUGE CHART

LOCATING

A. Remove shipping skid by unscrewing bolts with an adjustable

wrench.

B. Carefully lift freezer off the shipping skid.

C. Free plug and cord from inside the lower front of the unit (do

not plug in power source).

D. Your TRUE equipment should be placed close enough to the

electrical supply so that extension cords are never used.

E. Applicance tested according to the climate classes 5 and 7 for

temperature and relative humidity.

LEVELING

A. Set unit in its final location. Be sure there is adequate ventilation

in your room. Under extreme heat conditions, (100°F+,

38°C+), you may want to install an exhaust fan.

WARNING: WARRANTY IS VOID IF VENTILATION IS

INSUFFICIENT.

B. Proper leveling of your TRUE cooler is critical to operating

success (for non-mobile models). Effective condensate removal

and door operation will be effected by leveling.

C. The cooler should be leveled front to back and side to side with

a level.

D. Ensure that the drain hose or hoses are positioned in the pan.

E. Free plug and cord from inside the lower rear of the cooler

(do not plug in).

F. The unit should be placed close enough to the electrical supply

so that extension cords are never used.

NOTE: IF THE CABINET HAS A CENTER LEVELING

SCREW, CASTOR, OR LEG, MAKE SURE IT

IS ADJUSTED PROPERLY SO IT MAKES FULL

CONTACT WITH THE FLOOR AFTER THE CABINET

HAS BEEN LEVELED.

WARNING: CABINET WARRANTIES ARE VOID IF

OEM POWER CORD IS TAMPERED WITH.TRUE WILL

NOT WARRANTY

ANY UNITS THAT ARE

CONNECTED TO AN

EXTENSION CORD.

GLASS CHILLER

Removing skid from

bottom of cabinet.

G L A S S C H IL L E R

TRUE

tmw www.truemfg.com

1 2

7 8

5 6

STANDARD ACCESSORIES

MODELS TMW-36F AND TMW-36-F-QT

REVERSIBLE LID INSTRUCTIONS

A. Remove lid. See figure 1.

Lift top cover off unit and rotate 180 degrees. See figures 2 & 3.

C. Lower top cover onto locking pins. See figure 4.

D. Lower lid into place. See figures 5 & 6.

MODEL TMW-36F-FT-SD

REVERSIBLE LID INSTRUCTIONS

Model TMW-36F-FT-SD includes two sets of lid. There is a vertical

set and a horizontal set. Image 7 shows the TMW-36F-FT-SD before

lids are installed.

A. With the temperature display facing you, the vertical lids will

slide from front to back. See image 8.

B. With the temperature display facing you, the horizontal lids will

slide from left to right.

SETUP

Vertical lids shown.

TRUE

tmw www.truemfg.com

STARTUP

A. The compressor is ready to operate. Plug in the cooler.

B. Temperature control gives freezers an approximate temperature

of -10°F. Allow unit to function several hours, completely

cooling cabinet before changing the control setting.

Temperature Control Location and Settings.

• LAE temperature control is located on the front of cabinet.

• Mechanical temperature control is located behind access grill.

See website for adjustments, sequence of operation, and more

information.

C. Excessive tampering with the control could lead to service

difficulties. Should it ever become necessary to replace

temperature control, be sure it is ordered from your TRUE

dealer or recommended service agent.

D. Good air flow in your TRUE unit is critical. Be careful to

load product so that it neither presses against the back wall,

nor comes within four inches of the evaporator housing.

Refrigerated air off the coil must circulate down the back wall.

NOTE: If the unit is disconnected or shut off, wait five minutes

before starting again.

RECOMMENDATION - Before loading product we recommend

you run your TRUE unit empty for two to three days.This allows you

to be sure electrical wiring and installation are correct and no ship-

ping damage has occurred. Remember, our factory warranty does not

cover product loss!

OPERATION

MECHANICAL CONTROL TMW GENERAL SEQUENCE OF OPERATION

1. Cabinet is plugged in.

2. The compressor only will start if the temperature control is calling for cooling. (If the compressor does not start, verify that the

temperature control is not in the “OFF” or “0” position.

3. The temperature control will cycle the compressor on and off.

a. The temperature control is sensing the air temperature.

b. The temperature control should be set on the #4 or #5.

c. The warmest setting is #1, the coldest is #9, and #0 is the off position.

d. The thermometer is designed to read and display a cabinet temperature not a

product temperature.

The thermometer may reflect the refrigeration cycle swings of up and down

temperatures.

The most accurate temperature on a cabinet's operation is to verify the

product temperature.

4. The control will not initiate defrost.

a. The cabinet will need to be manually defrosted. The manual defrost frequency

will depend on the unit's usage, environment and the amount of frost.

GLASS CHILLER

Mechanical

Temperature

Control

MECHANICAL TEMPERATURE CONTROLS

AIR SENSING

An air sensing temperature control used in a freezer application will require a defrost cycle to

ensure that the evaporator coil is kept clear of frost and ice.

TRUE

tmw www.truemfg.com

INSTALLATION INSTRUCTIONS

DANFOSS TEMPERATURE CONTROL ADJUSTMENT

FOR HIGH ALTITUDE APPLICATIONS:

REQUIRED TOOLS:

• Allen Wrench (5/64")

• Torx Screw (T-7)

TERMS:

Cut-out - Temperature sensed by the controller that shuts the

compressor off.

Cut-in - Temperature sensed by the controller that turns the

compressor on.

WHEN TO MAKE AN ADJUSTMENT TO A MECHANICAL TEMPERATURE CONTROL

OPERATION INSTRUCTIONS:

REQUIRED TOOLS:

• Jewelers Screw Driver (Small Screw Driver)

GE CONTROL INSTRUCTIONS:

The scale to the right may be used as a guide for measuring

degrees of rotation required for altitude correction. See Figure 1.

The arrows indicate direction of screw rotation. Turn calibration

screw clockwise to obtain warmer operating temperatures.

NOTE: Each 1/4 turn of the calibration screw is equal to

approximately 2 degrees F. Do not make more than 3/4 turn.

After making adjustment, measure temperature during three

cycles before adjusting again.

NOTE: Only adjust the screw

(small flathead) on the face of

the control (next to the cam).

See Figure 3.

Follow the Altitude Correction

Table to the right.

We advise to make a mechanical temperature control adjustment only for a high altitude location.

Compressor

Ter minals

Ground

Terminal

To adjust the temperature control

take the control knob off to view the

cut-in screw. (See Photo Above)

Front of Temperature Control

Calibration

Screw

1 2

Cut-out Adjustment

Screw Allen (5/64" or 2 mm.)

Cut-in Adjustment

Screw Torx (T-7)

Compressor

Connection

ALTITUDE CORRECTION TABLE:

CALIBRATION SCREW ADJUSTS

BOTH CUT-IN AND CUT-OUT

Altitude (Feet)

2000

3000

4000

5000

6000

7000

8000

9000

10,000

Clockwise Turns

7/60

11/60

15/60

19/60

23/60

27/60

30/60

34/60

37/60

Compressor Connection

(double terminal)

HOW TO ADJUST A MECHANICAL TEMPERATURE CONTROL

Altitude Correction

Scale Guide for Measuring Back of Temperature Control

Bottom of Temperature Control

TRUE

tmw www.truemfg.com

INSTALLATION INSTRUCTIONS

TEMPERATURE CONTROL ALTITUDE ADJUSTMENT:

REQUIRED TOOLS:

• Allen Wrench (5/64”)

• Torx Screw (T-7)

The scale to the right may be used as a guide for measuring degrees of rotation required for altitude

correction. The arrows indicate direction of screw rotation. See Figure 1.

IMPORTANT: Upright models ordered with “High Altitude” temperature controls are

pre-calibrated and do not require adjustment.

180

270

360

Scale Guide for Measuring

INSTRUCTIONS: DANFOSS TEMPERATURE CONTROL ADJUSTMENT FOR

HIGH ALTITUDE APPLICATIONS

STEP 1 - Unplug cooler.

STEP 2 - Remove the screws that secure the temperature control to the inset box.

STEP 3 - To make these adjustments it may be necessary to remove the temperature control from the housing.

NOTE: You may have to remove the wires attached to the control. Take note as to which wire is on which spade terminal.

STEP 4 - Pull out gently from cabinet.

NOTE: Mechanical temperature controllers are affected when functioning at high altitude.

The cut-in and cut-out temperatures will be colder than when the controller functions closer to sea level.

STEP 5 - For high elevation installations, it may be necessary to “warm-up” the set points. To make the adjustment, insert the

appropriate tool in each adjustment screw and turn 1/4 of a revolution clockwise (to the right). This procedure will adjust both

the cut-in and cut-out about 2˚F warmer.

STEP 6 - Make sure to reconnect the wires to the proper spade terminal when reinstalling.

INSTRUCTIONS: CUTLER HAMMER TEMPERATURE CONTROL ALTITUDE ADJUSTMENT

STEP 1 - Unplug cooler.

STEP 2 - Turn the temperature control to the “9” position.

STEP 3 - Remove the screws that secure the mounting plate to the evaporator top. See Figure 2.

STEP 4 - Pull control down gently from housing.

STEP 5 - Turn screws counterclockwise (CCW).

STEP 6 - Reassemble to cooler housing and return the temperature control to the “5” position.

TRUE

tmw www.truemfg.com

CUT

OUT

CUT

COLDER

BUL. NO.

CHART

CCW Adjustment

(based on 360°/

complete turn)Height

2000' 42°

3000' 78°

4000' 114°

5000' 150°

6000' 186°

7000' 222°

8000' 258°

9000' 294°

10,000' 330°

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere True Manufacturing Company Gefrierschrank Handbücher

True Manufacturing Company

True Manufacturing Company TPP-67 Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company T-23-HC Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company 922341 Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TUC-27FG Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company T-23DF-HC Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company STR Series Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company GDM-26 Installations- und Betriebshandbuch

True Manufacturing Company

True Manufacturing Company TDC-47 Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TGU-2-HC Bedienungsanleitung

Beliebte Gefrierschrank Handbücher anderer Marken

Siemens

Siemens GU..D SERIES Bedienungsanleitung

Omcan

Omcan FR-CN-0155 Bedienungsanleitung

Beko

Beko FNE290E24W Bedienungsanleitung

Electrolux

Electrolux ARCTIS G 8 60 50-6I Bedienungsanleitung

Electrolux

Electrolux EUF2042AOX Bedienungsanleitung

Dometic

Dometic CoolFreeze CFX95DZ Bedienungsanleitung

Electrolux

Electrolux EUF7000W1 Bedienungsanleitung

Polar Electro

Polar Electro CT330 Bedienungsanleitung

MPM

MPM MPM-145-SK Series Bedienungsanleitung

SAF

SAF PRESTOTIG 200AC/DC Kurzanleitung

Zanussi

Zanussi ZFT11407WA Bedienungsanleitung

AEG

AEG A63190GT Bedienungsanleitung

AEG

AEG A81000TNW0 Bedienungsanleitung

Matsui

Matsui MUC50S15E Bedienungsanleitung

NEFF

NEFF G4344X8 Bedienungsanleitung

Frigidaire

Frigidaire FV 1246 H Bedienungsanleitung

Frigidaire

Frigidaire FFC13K1AW Bedienungsanleitung

Electrolux

Electrolux EU 2400C Bedienungsanleitung