True Manufacturing Company TCGR-50 Bedienungsanleitung

............ www.truemfg.com ............

INSTALLATION MANUAL FOR

TCGR DISPLAY CASES (REFRIGERATED BAKERY & COLD DELI) MODELS

CURVED GLASS DISPLAY CASES

- REFRIGERATED BAKERY & COLD DELI -

CONGRATULATIONS!

You have just purchased the finest commercial

refrigeration available. You can expect many years

of trouble-free operation.

TRUE FOOD SERVICE EQUIPMENT, INC.

2001 East Terra Lane • P.O. Box 970 • O’Fallon, Missouri 63366

(636)-240-2400 • FAX (636)272-2408 • INT’L FAX (636)272-7546 • (800)325-6152

Parts Department (800)424-TRUE • Parts Department FAX# (636)272-9471

TABLE OF CONTENTS

Safety Information

Safety Precautions ––––––––––––––––––––––– 1

Proper Disposal –––––––––––––––––––––––––– 2

Connecting Electricity ––––––––––––––––––––– 3

Adapter Plugs ––––––––––––––––––––––––––– 3

Installation / Operation Instructions

Ownership –––––––––––––––––––––––––––––– 4

Required Tools ––––––––––––––––––––––––––– 4

Uncrating ––––––––––––––––––––––––––––––– 4

Locating –––––––––––––––––––––––––––––––– 5

Leveling Cabinet ––––––––––––––––––––––––– 5

Electrical Instructions ––––––––––––––––––––– 6

Wire Gauge Chart –––––––––––––––––––––––– 7

Start-up –––––––––––––––––––––––––––––––– 8

Shelving Installation –––––––––––––––––––– 9-10

Installing Optional Castors –––––––––––––––– 11

Installing Optional Formica Kit ––––––––––––– 12

Maintenance, Care & Cleaning

Optional Sealing Cabinet To Floor –––––––––– 13

Cabinet Cleaning –––––––––––––––––––––––– 13

Light Bulb Replacement –––––––––––––––––– 14

Temperature Control Adjustment ––––––––––– 15

Cleaning The Condenser –––––––––––––––––– 16

Important Warranty Information –––––––––––– 17

Stainless Steel Equipment Care and

Cleaning ––––––––––––––––––––––––––––– 18-19

Warranty (U.S.A. and Canada ONLY!) ––––––– 20

TCGR-77

TCGR-50

TCGR-50-CD

11/18/08 500 SB #912628

*Spanish, German, French, and Dutch versions included.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

SAFETY INFORMATION

• This display case must be properly installed

and located in accordance with the Installation

Instructions before it is used.

• Do not allow children to climb, stand or hang

on the shelves in the display case. They could

damage the refrigerator and seriously injure

themselves.

• Do not touch the cold surfaces in the refrigerat-

ed compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

• Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

• Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small; be

careful closing doors when children are in the

area.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

• Unplug the refrigerator before cleaning and

making repairs (switch power off at breaker for

hard wired models).

• Setting temperature controls to the 0 position

does not remove power to the light circuit,

perimeter heaters, or evaporator fans.

WARNING!

Use this appliance for its intended purpose as described in this Owner Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

How to Maintain Your Unit

to Receive the Most Efficient and

Successful Operation

You have selected one of the finest display cases made. It is manufactured under strict quality

controls with only the best quality materials available. Your TRUE cooler, when properly

maintained, will give you many years of trouble-free service.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

2 2

SAFETY INFORMATION

PROPER DISPOSAL OF THE DISPLAY CASE

DANGER!

RISK OF CHILD ENTRAPMENT

USE OF EXTENSION CORDS

NEVER USE AN EXTENSION CORD! TRUE will not warranty any display case that has been connected to an

extension cord.

Child entrapment and suffocation are not problems

of the past. Junked or abandoned display cases are

still dangerous… even if they will sit for “just a few

days.” If you are getting rid of your old display case,

please follow the instructions below to help pre-

vent accidents.

Before You Throw Away Your Old Display Case:

•Take off the doors.

•Leave the shelves in place so that children may

not easily climb inside.

Refrigerant Disposal

Your old refrigerator may have a cooling system

that uses “Ozone Depleting ” chemicals. If you are

throwing away your old refrigerator, make sure the

refrigerant is removed for proper disposal by a

qualified service technician. If you intentionally

release any refrigerants you can be subject to

fines and imprisonment under provisions of the

environmental regulations.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

Before your new display case is connected to a

power supply, check the incoming voltage with a

voltmeter. If anything less than 100% of the rated

voltage for operation is noted, correct immediately.

Have the circuit checked by a qualified electrician

to make sure it is properly grounded.

The display case should always be use it’s own

individual electrical circuit, which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading building wiring circuits which

could cause a fire hazard from overheated wires.

For models with standard power cord.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the circuit checked by a qualified electrician

to make sure it is properly grounded.

If the outlet is a standard 2-prong outlet, it is your

personal responsibility and obligation to have it

replaced with the properly grounded 3-prong wall

outlet.

The display case should always be plugged into

it’s own individual electrical circuit, which has a

voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading building wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your display case by pulling on

the power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When removing the display case away from the

wall, be careful not to roll over or damage the

power cord.

HOW TO CONNECT ELECTRICITY

Hard wiring is required on specific Display Cases.

Models standard with power cords: Do not, under any circumstances, cut or remove the third (ground) prong

from the power cord.

For personal safety, this appliance must be properly grounded.

WARNING!

NOTE

Hard wired models do not use this receptacle.

USE OF ADAPTER PLUGS

NEVER USE AN ADAPTER PLUG! Because of potential safety hazards under certain conditions, we strongly

recommend against the use of an adapter plug.

SAFETY INFORMATION

NEMA plugs

TRUE uses these types of plugs.

If you do not have the right outlet

have a certified electrician install

the correct power source.

115/60/1

NEMA-5-20R

............ www.truemfg.com ............

True Food Service Equipment, Inc.

4 4

INSTALLATION / OPERATION INSTRUCTIONS

To insure that your unit works properly from the

first day, it must be installed properly. We highly

recommend a trained mechanic and electrician

install your True equipment. The cost of a profes-

sional installation is money well spent.

Before you start to install your True unit, carefully

inspect it for freight damage. If damage is discov-

ered, immediately file a claim with the delivery

freight carrier.

True is not responsible for damage incurred during

shipment.

OWNERSHIP

• Tin Snips / Band Cutters

• Claw Hammer

• Hex Head Driver

• Adjustable Wrench

• 3/4" (19 mm) Open-End Wrench

• Phillips Head Screwdriver

• Level

REQUIRED TOOLS

Step 1

The following procedure is recommended for

uncrating the unit:

A. Cut metal retaining straps securing protective

top skid. Remove the outer packaging by pull-

ing tri-wall nails from skid. Remove (4) card-

board corner pads and dust cover.

B. Inspect for concealed damage. Again, immedi-

ately file a claim with the freight carrier if there

is damage.

C. Move your display case as close to the final loca-

tion as possible before removing the wooden

skid.

UNCRATING

INSTALLATION / OPERATION INSTRUCTIONS

•Remote cabinets must be ordered as remote. We

do not recommend converting a standard self

contained to remote system.

•All remote cabinets must be hard wired.

•Remote cabinets are not available with castors.

•All remote cabinets come standard using 404A

refrigerant.

•All remote units come standard with expansion

valve, liquid line solenoid, heated condensate pan,

and defrost timer when applicable.

•Contact True Technical Service for BTU require-

ments.

•No wiring necessary between cabinet and con-

densing unit.

•All remote condensing units purchased from True

are 208/230 volts single phase.

If you have any questions regarding this section,

please call True at 1 (800) 325-6152.

REMOTE UNITS

(This section applies to remotes only!)

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

TOOLS REQUIRED:

• Phillips screw driver

• 3/8” (9.5 mm) socket or 3/8” (9.5 mm) wrench

Step 2

A. Use a Phillips screw diver and remove four

screws from the L-bracket connected the unit to

the wood skid (image 1). Then use a 3/8” (9.5

mm) socket or wrench and remove the L-brack-

et from the unit (image 2).

To avoid damage to glass DO NOT lay cabinet

on its side or back when removing skid,

installing leg levelers, cleaning, etc.

B. Lift up from the base and walk unit off the skid

and set in final location.

C. Unblock doors, (free plastic wedges, blue foam

and tape. Remove fiberglass tape securing glass.

Remove components: (shelves, brackets, etc.)

from inside cabinet.

LOCATING

Step 3

A. Set unit in its final location. Be sure there is

adequate ventilation in your room. Under

extreme heat conditions, (100°F+, 38°C+), you

may want to install an exhaust fan.

Warning

Warranty is void if ventilation is insufficient.

B. Proper leveling of your True unit is critical to

operating success (for non-mobile models).

Effective condensate removal and door operation

will be effected by leveling.

Warning

Display case must be leveled accurately to ensure

front glass door seals properly.

C. The unit should be leveled front to back and

side to side with a level. Place the level in the

interior floor of the unit and check all four sides.

D. If the cabinet is not level adjust leg levelers by

first relieving weight to leveler and adjusting

by either hand or wrench. Repeat with all leg

levelers until cabinet is level in all directions.

E. Ensure that the drain hose or hoses are

positioned in the pan.

F. Models with power cord: Free plug and cord

from inside the lower rear of the cooler (do not

plug in).

G. Models with power cord: The unit should be

placed close enough to the electrical supply so

that extension cords are never used.

Warning

Compressor warranties are void if the unit is more

than 9 ft. (3 m) from plug-in connection or an

extension cord is used to connect unit to a power

supply.

LEVELING

Removing bracket

from skid.

Removing bracket from cabinet.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

6 6

INSTALLATION / OPERATION INSTRUCTIONS

Step 4

NOTE

Hard wiring for a 30 amp circuit is required on

specific Bakery Cases.

A. Before your new unit is connected to a power

supply, check the incoming voltage with a

voltmeter. If anything less than 100% of the

rated voltage for operation is noted, correct

immediately.

B. Models equipped with 9 ft. (3 m) power cord

must be powered at proper operating voltage at

all times.

Refer to cabinet data plate for voltage.

True requires that a sole use circuit be dedicated

for the unit.

WARNING

Compressor warranties are void if compressor burns

out due to low voltage.

WARNING

Power supply cord ground should not be removed!

NOTE

To reference wiring diagram - Remove lower rear

grill. Wiring diagram is positioned on the ballast box

inside lower rear of the cabinet.

ELECTRICAL INSTRUCTIONS

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

CONDUCTORS AND CIRCUITS

Wire Gauge for 2% Voltage Drop in Supply Circuits.

115 Volt Distance In Feet To Center of Load

Amps 20 30 40 50 60 70 80 90 100 120 140 160

2 14 14 14 14 14 14 14 14 14 14 14 14

3 14 14 14 14 14 14 14 14 14 14 14 12

4 14 14 14 14 14 14 14 14 14 12 12 12

5 14 14 14 14 14 14 14 12 12 12 10 10

6 14 14 14 14 14 14 12 12 12 10 10 10

7 14 14 14 14 14 12 12 12 10 10 10 8

8 14 14 14 14 12 12 12 10 10 10 8 8

9 14 14 14 12 12 12 10 10 10 8 8 8

10 14 14 14 12 12 10 10 10 10 8 8 8

12 14 14 12 12 10 10 10 8 8 8 8 6

14 14 14 12 10 10 10 8 8 8 6 6 6

16 14 12 12 10 10 8 8 8 8 6 6 6

18 14 12 10 10 8 8 8 8 8 8 8 5

20 14 12 10 10 8 8 8 6 6 6 5 5

25 12 10 10 8 8 6 6 6 6 5 4 4

30 12 10 8 8 6 6 6 6 5 4 4 3

35 10 10 8 6 6 6 5 5 4 4 3 2

40 10 8 8 6 6 5 5 4 4 3 2 2

45 10 8 6 6 6 5 4 4 3 3 2 1

50 10 8 6 6 5 4 4 3 3 2 1 1

Wire Gauge for 2% Voltage Drop in Supply Circuits.

230 Volt Distance In Feet To Center of Load

Amps 20 30 40 50 60 70 80 90 100 120 140 160

5 14 14 14 14 14 14 14 14 14 14 14 14

6 14 14 14 14 14 14 14 14 14 14 14 12

7 14 14 14 14 14 14 14 14 14 14 12 12

8 14 14 14 14 14 14 14 14 14 12 12 12

9 14 14 14 14 14 14 14 14 12 12 12 10

10 14 14 14 14 14 14 14 12 12 12 10 10

12 14 14 14 14 14 14 12 12 12 10 10 10

14 14 14 14 14 14 12 12 12 10 10 10 8

16 14 14 14 14 12 12 12 10 10 10 8 8

18 14 14 14 12 12 12 10 10 10 8 8 8

20 14 14 14 12 10 10 10 10 10 8 8 8

25 14 14 12 12 10 10 10 10 8 8 6 6

30 14 12 12 10 10 10 8 8 8 6 6 6

35 14 12 10 10 10 8 8 8 8 6 6 5

40 14 12 10 10 8 8 8 6 6 6 5 5

50 12 10 10 8 6 6 6 6 6 5 4 4

60 12 10 8 6 6 6 6 6 5 4 4 3

70 10 10 8 6 6 6 5 5 4 4 2 2

80 10 8 8 6 6 5 5 4 4 3 2 2

90 10 8 6 6 5 5 4 4 3 3 1 1

100 10 8 6 6 5 4 4 3 3 2 1 1

............ www.truemfg.com ............

True Food Service Equipment, Inc.

8 8

Step 5

A. The compressor is ready to operate. Plug in the

display case.

B. Check the temperature control setting in the

lower right of the cabinet backside. The setting

should be at No. 3 position to maintain an

approximate temperature of 38°F (3.3°C). Set

defrost time clock to the correct time of day.

Allow unit to function several hours, completely

cooling cabinet before changing the control

setting.

C. Excessive tampering with the control could lead

to service difficulties. Should it ever become

necessary to replace temperature control, be

sure it is ordered from your True dealer or

recommended service agent.

D. Good air flow in your True unit is critical. Be

careful not to overstock product or block air

vents.

E. Verify that the cabinet lights are working.

Bakery cases are shipped with light switches in

the "on" position. The toggle switch is located

lower right corer at the rear.

NOTE

If the unit is disconnected or shut off, wait five

minutes before starting again.

RECOMMENDATION

Before loading product we recommend you run your

True unit empty for two to three days. This allows you

to be sure electrical wiring and installation are correct

and no shipping damage has occurred. Remember,

our factory warranty does not cover product loss!

REPLACEMENT PARTS

TRUE maintains a record of the cabinet serial number

for your unit. If at any time during the life of your

display case, a part is needed, you may obtain this

part by furnishing the model number and serial

number to the company from whom you purchased

the cabinet. Call Toll-Free: (800)-424-TRUE (Direct to

Parts Department). (800)-325-6152 (U.S.A. & Canada

only) or call: (636)-240-2400.

STARTUP

INSTALLATION / OPERATION INSTRUCTIONS

REFRIGERATED CURVED GLASS

DISPLAY CASES

Hard wired Display Cases are equipped

with a service receptacle (found on

the upper right cabinet backside). No

electrical load greater than 4.0 amps

should be connected to it.

Andere Handbücher für TCGR-50

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere True Manufacturing Company Kühlschrank Handbücher

True Manufacturing Company

True Manufacturing Company TBB-2 Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TDB-24-48-1-G-1 Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company GDM-3 Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TBR Series Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TR1RRI-1S Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TMW TMW-36F Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TMW TMW-36F Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company GDM Series Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company 30 Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TCGR-50 Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company TGU-2 Bedienungsanleitung

True Manufacturing Company

True Manufacturing Company GDM-HST02-HC-TSL01 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung

Matsui

Matsui MTT50W12E Bedienungsanleitung