TrueNAS ES60 Handbuch

TrueNAS®ES60 Expansion Shelf

Basic Setup Guide

September 2017 Edition

1 ES60 Expansion Shelf

The TrueNAS®ES60 Expansion Shelf is a is a 4U, 60-bay storage expansion unit designed speciﬁcally for use

with the TrueNAS®Z Series Uniﬁed Storage Array.

Note: TrueNAS®units are carefully packed and shipped with trusted carriers to arrive in perfect condition.

If there is any shipping damage or any parts are missing, please take photos and contact iXsystems support

immediately at [email protected] or 1-855-GREP4-iX (1-855-473-7449) or 1-408-943-4100.

Please locate and record the hardware serial numbers on the back of each chassis for easy reference.

Carefully unpack the shipping boxes and locate these components:

ES60 Expansion Shelf 60 Drive trays

Rail kit with mounting hardware Two SAS cables (additional cables included if or-

dered)

Two power cables

1.1 Become Familiar With the System

Front view of the ES60 Expansion Shelf:

Front panel indicators:

Front view of the ES60 Expansion Shelf:

System Drive Tray:

1.2 Install Rack Mounting Rails

Remove the rail set and screws from the rail kit box. Use only the screws labeled for use in the type of

rack provided. Have two people support each rail while mounting it to the rack using the top and bottom

screw holes. The rail surface should remain inside of the rack boundaries. These images show proper rail

installation with the front and rear of the rails mounted.

Front View

Rear View

Side View, No Rail

Side View, Rail Mounted

Rack Rail, Front

Rack Rail, Rear

1.3 Install the ES60 Expansion Shelf in the Rack

Caution: Two people are required to safely lift the chassis for rack installation or removal. Do not

install drives until after the chassis has been installed in the rack, and remove all drives before removing

the chassis from the rack.

Align the chassis rails with the installed rack rails and gently slide the chassis into the rack until it stops.

Press in the slide locks, then slide the chassis in until the face of the ES60 is ﬂush with the rack.

Image

1.4 Attach the Expansion Shelf to the Front of the Rack

Press in and turn the built-in thumbscrews to the front of the rack.

Image

1.5 Install the Drives in the Expansion Shelf

To insert a drive, release the handle with the tab on the front of the drive chassis, push it into a drive bay

until the drive handle begins to move into place, then push it the rest of the way until the handle locks into

place.

Image

1.6 Plug in the SAS Cables

Refer to the Wiring Guide. (REF THE IMAGE)

1.7 Plug in the Power Cables

Plug both power cables into the power outlets and secure the cables with the plastic cable locks. This will

turn on the Expansion Shelf.

Note: Service and management ports are not used during normal operation and should not be connected.

IMAGE

If setting up a TrueNAS®Storage Array for the ﬁrst time, wait two minutes after turning on the Expansion

Shelf before powering on the TrueNAS®Array. If you already have a TrueNAS®Array in operation, you may

power on the Expansion Shelf at any time.

1.8 Install the Bezel

The back of the bezel has two screws on the left and right side. Align the two screw holes on each side with

the back of the ears on the ES60. Begin by screwing in one screw on one side, then screw in diagonally on

the opposite side. Do this for the next two screws.

IMAGE

1.9 Install the Cable Management Arm

On the rear of the ES60 JBOD, locate the two pin posts on the left side of the expansion shelf. Align the holes

on the bracket of the cable management arm with the posts on the chassis. Slide the cable management

arm forward and pull the lever on the latch upwards to lock the cable management arm into place.

IMAGE

Unscrew the two screws already attached to this side of the cable management arm. Align with the screw

holes for this end and screw them in. Both pieces are now attached to the chassis.

IMAGE

1.10 Lock in the Power Cable

This step eliminates the risk of accidentally disconnecting the power cable.

IMAGE

Insert the power cable into the plastic clamp and press down on the tab to lock the power cable in place.

IMAGE

1.11 Secure the Power Cords

Route and secure the power cords and other cables (including SAS cables) onto the cable-management arm,

as shown in the pictures below.

IMAGE

The ﬁnal assembly should look like this picture.

IMAGE .. index:: User Guide Location

2 User Guide

The TrueNAS®User Guide with complete conﬁguration instructions is available by clicking Guide in the

TrueNAS®user interface or at https://support.ixsystems.com/truenasguide/truenas.html.

3 Contacting iXsystems

For assistance, please contact iX Support:

Contact Method Contact Options

Web https://support.ixsystems.com

Email [email protected]

Telephone Monday - Friday, 8:00AM to 5:00PM Paciﬁc Standard Time:

•1 (855) 473-7449 option 2 (US-only toll-free)

•1 (408) 943-4100 option 2 (local and international)

Telephone After Hours (24x7 Gold Level Support only):

•1 (855) 499-5131 (US-only toll-free)

•1 (678) 835-6101 (local and international)

Andere Handbücher für ES60

Inhaltsverzeichnis

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung