Trust ACM-3000H2 Bedienungsanleitung

START-LINE

ACM-3000H2

ACM-3000H2 BUILT-IN SWITCH

Item 71148 Version 1.0

Visit www.trust.com

for the latest instructions

USER MANUAL

MULTI LANGUAGE

5mm

01 02

Com S1 S2 N L

01 02

Com S1 S2 N L

01 02Com S1 S2 N L

9.1

01 02 S1 S2 N L

COM

Wall switch

ACM-3000H2

Switch 1a

Switch 2a

Switch 1b Switch 2b

01 02Com S1 S2 N L

1 SEC

01 02 S1 S2 N L

COM

Wall switch

ACM-3000H2

Switch 2Switch 1

9.2

9.3

01 02Com S1 S2 N L

ININ OUT

N N

01 02Com S1 S2 N L

1 SEC

OFF

01 02Com S1 S2 N L

8 SEC 1 SEC

ACM-3000H2 BUILT-IN SWITCH

1. Disable mains power

Always turn OFF the mains power (In the meter closet) before you begin the installation or removal

of this product. The ACM-3000H2 can be used for either one or two hotel switches, connected with

one or two lamps. Also, the ACM-3000H2 can be used for one or two single wall switches, which are

connected with one or two lamps.

2. Loosen ceiling lights

Remove the existing lighting/equipment from the ceiling, leaving the wires connected to the lighting.

Lighting/equipment, may not exceed the maximum of 3000 watts.

3. Warning for stripping wires

3A. Make sure the wires are stripped for 5mm.

3B. When connecting the wires to the ACM-3000H2 make sure the stripped wires are pressed ﬁrmly

in the module, no exposed wires are visible and the wires cannot touch each other. This can cause a

short circuit.

4. Disconnect the switch wire and neutral wire

To install the ACM-3000H2 disconnect the switch wire and neutral wire of lamp 1. (Disconnect from

terminal block or cut the wires if necessary) Disconnect the switch wire and neutral wire of lamp 2.

Consult an electrician if in doubt about wire colours.

5. Connect the live wire and the neutral wire to a terminal block

(a) Connect the live wire from the ceiling box to a terminal block. Connect the other end of the live

wire also back into the same terminal block.

(b) Connect the neutral wire from the ceiling box to a dierent terminal block. Make sure other Trust

Smart Home receivers are placed at least 50 cm from the ACM-3000H2 to prevent interference.

6. Connect the switch wire and neutral wire of the lamp to the terminal block

(a) Connect the wall switch wire of lamp 1 from the ceiling box to the [S1] contact.

(b) Connect the (blue) neutral wire from lamp 1 to the terminal block of the neutral wire. Connect a

new wire from the neutral terminal block on to the [N] contact.

ACM-3000H2 BUILT-IN SWITCH

(d) Connect two new live wires from the live wire terminal block to the [L] and [COM] contact.

(e) Tighten the terminal screws of the ACM-3000H2.

7. Connect second lamp and wall switch.

(a) Pull the switch wire from the wall switch of lamp 2 to the ceiling box of lamp 1. Pull the switch wire

from lamp 2 to the ceiling box of lamp 1.

(b) Connect the switch wire of lamp 2 to the [O2] contact

This is an technical installation schematic of the ACM-3000H2 with two wall-switches (1 hotel/stairwell

circuit).

This is an technical installation schematic of the ACM-3000H2 with four wall-switches (2 hotel/stairwell

circuit.

8. Enable mains power

Switch the mains power ON before proceeding with the installation.

Make sure no stripped parts of wires are touched after this step.

The LED indicator on the receiver will be lit for a few seconds when voltage is applied.

9.1 Activate pairing mode

Press for about 1 second (with a pointed object) on the Connect button to activate the pairing mode.

The pairing mode will be active for 15 seconds and the LED indicator on the receiver will ﬂash slowly.

9.2 Send an ON signal

While the LED indicator ﬂashes, press the ON button on a Trust Smart Home transmitter to pair the

transmitter to the ACM-3000H2. (Or activate a Trust Smart Home sensor).

ACM-3000H2 BUILT-IN SWITCH

9.3 Pairing conﬁrmation

The LED on the module will blink 2x in order to conﬁrm that the code is stored. Repeat steps 9.1 to 9.3

for the second lamp with the other pairing button. The receiver can store up to 6 dierent transmitter

codes in its memory per channel. The memory is retained when the receiver is installed elsewhere or

when there is a power failure.

10. Placing the receiver

Place the receiver in the ceiling box. Mount the lights back in place or use a cover.

Make sure that you can always reach the receiver, for example, to reset it, or to register a new

transmitter.

Make sure no stripped parts of wires touch each other.

11. Wireless control

Send with the transmitter an ON signal to turn the light on wirelessly.

Send with the transmitter an OFF signal to turn the light o wirelessly.

Consult the manual of the transmitter for more information.

The existing wall switches which are used to control the connected lighting can still be used.

Deleting a single transmitter code

(a) Press for about 1 second on the Connect button. The ‘pairing mode’ will be active for 15 seconds

and the LED indicator on the receiver will ﬂash slowly.

(b) Send while the ‘pairing mode’ is active with the connected Trust Smart Home transmitter an

OFF signal. If necessary, consult the instruction manual of the transmitter.

Repeat this procedure to delete several transmitters from the receiver.

ACM-3000H2 BUILT-IN SWITCH

Erase entire memory

(a) Press the Connect button for about 8 seconds until the LED indicator ﬂashes quickly.

(b) When the LED indicator ﬂashes rapidly, press the Connect button again for 1 second to conﬁrm

that you want to completely erase the memory.

Andere Handbücher für ACM-3000H2

Inhaltsverzeichnis

Andere Trust Schalten Handbücher

Trust

Trust HU-3340p Bedienungsanleitung

Trust

Trust SMART Home START-LINE RECEIVER ACM-3500-3 Bedienungsanleitung

Trust

Trust APC Starter Set Wireless Switching Bedienungsanleitung

Trust

Trust 12276 Bedienungsanleitung

Trust

Trust 73182 Bedienungsanleitung

Trust

Trust HU-4440p Bedienungsanleitung

Trust

Trust START-LINE APA3-1500R Bedienungsanleitung

Trust

Trust 411E Bedienungsanleitung

Trust

Trust 12914 Bedienungsanleitung

Trust

Trust HU-1140P Bedienungsanleitung

Trust

Trust SmartHome ACM-1000 Bedienungsanleitung

Trust

Trust START-LINE AMU-500 Bedienungsanleitung

Trust

Trust PREMIUM ZCM-1800 Bedienungsanleitung

Trust

Trust 411F Bedienungsanleitung

Trust

Trust 71263 Bedienungsanleitung

Trust

Trust SECURITY PLUS-LINE AGST-8800 Bedienungsanleitung

Trust

Trust START-LINE ACM-2000 Bedienungsanleitung

Trust

Trust ZCC-3500 Bedienungsanleitung

Trust

Trust START-LINE ACC-2300 Bedienungsanleitung

Trust

Trust 11670 Bedienungsanleitung

Trust

Trust SMART Home START-LINE RECEIVER AWS-3500 Betriebsanleitung

Trust

Trust START-LINE AWST-9000Z Bedienungsanleitung

Trust

Trust HU-4445p Bedienungsanleitung

Trust

Trust START-LINE AWMR-230 Betriebsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung