TST TST-507-D-M Bedienungsanleitung
Wireless Tire Pressure and Temperature
Monitoring System Monochrome Display Manual
Wide Screen Monochrome Display
Model #: TST-507-D-M
Thank you for purchasing the TST Tire Pressure Monitoring
System. With minimal care, your new TPMS will
provide reliable service for many years. Please read and
understand the informaon contained within this manual.
Keep this manual for future reference.
Telephone: 770.889.9102
Website: www.tsruck.com
Document #: TST-Doc-507 WSD-MManual-(C)
INDEX
Page 1 - Display Features
Page 2 - Display Components and Controls
Pages 3 - 6 - Programming Sensor Codes Into the Display
- Automac Code Learning (Opon #1)
- Pressure Coding (Opon #2)
- Manual Coding (Opon #3)
Page 7 - Display Installaon
Page 7 - Display Buons
Page 8 - Parameter Sengs (Pressure & Temperature)
Page 9 - High Temperature and High Pressure Sengs
Page 10 - Low Pressure Alarm Sengs
Page 11 - Restore Display Factory Parameters
Page 11 - Display Alerts - Out of Parameter/Fast Leaks
Page 12 - Display Alerts - Sensor Low Baery Alert
Page 13 - Other Funcons
Pages 14 - 15 - Addional Funcons
Page 16 - Troubleshoong Tips
Pages 16 - 19 - Common Quesons
Page 19 - Display Specicaons
TST-Doc-507 WSD-M Manual-(C)
1
TST-Doc-507 WSD-M Manual-(C)
DISPLAY FEATURES
1) Large, wide screen LCD display of pressure and temperature.
2) Opons for Color or Monochrome screen.
3) Sucon cup and cradle mount included.
4) Integrated lithium baery that is rechargeable.
5) Wake-up acvaon of monitor when in moon.
6) Automac monitor illuminaon in dark condions.
7) Programmable high and low pressure alarm thresholds.
8) Programmable high temperature alarm.
9) Visual and audible warning alarms when temperature or
pressure exceeds thresholds.
10) Mulple pressure units: PSI, BAR.
11) Selectable temperature unit: °C or °F.
12) Program up to 110 res.
13) Tire pressure and temperature is displayed simultaneously
for quick viewing of each re.
14) The trailer res can be electronically removed from the
screen when not towing.
15) The towing vehicle res can be electronically removed from
the screen when parked.
16) Push buon programming.
17) A fully charged display will connuously operate 5-7 days on
baery power.
18) Temperature and pressure sengs are congured “per axle.”
2
TST-Doc-507 WSD-M Manual-(C)
DISPLAY COMPONENTS IN KIT
Pressure Unit: BAR or PSI, user-selectable temperature unit:
C° or F°, user-selectable.
DISPLAY CONTROLS
Display Holder
GO
SET
BACK
Monochrome Display
Power Adapter
Suction Cup Mount
Cradle Mount
3
TST-Doc-507 WSD-M Manual-(C)
PROGRAMMING SENSOR CODES INTO THE DISPLAY
Note: Your sensors will begin reading as soon as they
are coded into the display. Once you go back to the
main screen by pushing the “BACK” buon twice,
you may hear an alarm and see a pressure reading
of “0”. Simply press the (+) buon quickly to silence
the alarm.
Note: It is recommended to label each sensor
rst with the provided numbering code sckers,
similar to the following paern, before you code
the sensors. This allows you to know which sensor
is programmed to which re posion. You can also
write in your sensor number paern.
Or use your own numbering paern:
4
AUTOMATIC CODE LEARNING (opon #1)
Note: Code all the sensors to the display BEFORE screwing
them onto the re valve stem unless otherwise noted.
1. Push and hold the “SET” buon unl it beeps. You are
now in the programming mode. The “HI PRESSURE SET”
parameter will blink at the boom of the screen. Push
the (+) buon and scroll through the parameters unl
“LEARN ID” appears.
2. Quickly press and release the “SET” buon. The rst re
on the display will blink. If you want to program a dierent
re, press the (+) buon to move to the correct re. Push
the “SET” buon again and “FFF FFF” will ash. Put the
sensor for that re posion next to the display and press
the “GO” buon. The display will capture the sensor
code and show it on the screen. Again, push and release
the “SET” buon to save the code to that posion. When
coded correctly, a single beep will be heard and a six (6)
digit code will be shown.
3. Use the (+) buon to move to the next re posion you
want to program. Again, press the “SET” buon and
“FFF FFF” will blink. Put the sensor for that re posion
next to the display and press the “GO” buon to capture
the sensor code. Press “SET” again to save.
4. When you are nished programming all of your sensors,
press the “BACK” buon to return to the parameter
at the boom of the screen. Use the (+) or (-) buons
to scroll to another parameter, if necessary. If nished
programming, press the “BACK” buon again to go to
the Main Screen. (Your sensors will begin reading “0”
pressure and will alarm. Press the (+) buon to silence
the alarm while you connue your set-up).
TST-Doc-507 WSD-M Manual-(C)
5
TST-Doc-507 WSD-M Manual-(C)
Note: To delete a single sensor code:
Press the “SET” buon unl it beeps (approx. 3 seconds). Push
the (+) buon and scroll through the parameters unl “LEARN
ID” appears. Press and release the “SET” buon. Use the (+) or (-)
buons to scroll to the re you wish to remove. Press the “Set”
buon to select that re. It will start ashing. Press the “Back”
buon for 3 seconds. You will hear 3 beeps. The code will change
to “FFF FFF” which will be ashing. Press “SET” once. The ashing
will stop and the ID code will be deleted.
Note: To delete all of the re codes:
Press the “BACK” buon for 6 seconds. You will hear 6 beeps.
“DEL ALL” will appear on the screen. Press “SET” once. You will
hear one beep. “FFF FFF” will appear. All ID codes are deleted.
Note: When in the coding mode, the display will me-out within
approximately one (1) minute if no buons are pushed. At that
point, you will have to start the coding process again.
Note: Be sure the sensor being coded is at least two feet away
from the other sensors.
PRESSURE CODING (opon #2)
1. Be sure your sensors are numbered. Screw the sensors
partly onto each valve stem in the order you numbered
them. Do NOT screw them down far enough to hear air
hissing out.
2. Push the “SET” buon unl it beeps. You are now in the
programming mode. The “HI PRESSURE SET” parameter
will blink at the boom of the screen. Push the (+) buon
and scroll through the parameters unl “LEARN ID”
appears.
3. Quickly press and release the “SET” buon. The rst
re on the display will blink. If you want to program a
6
dierent re, press the (+) buon to move to the correct
re. Push the “SET” buon again and “FFF FFF” will ash.
4. Tighten the sensor down on the corresponding re valve
stem. The ID code will display and ash.
5. To save the ID code seng. Press “SET” once. It will beep
and sensor code is saved.
6. To remove the ID code seng, Press “BACK” once.
“FFF FFF” will re-appear. The seng will not be saved.
7. Press “BACK” twice to return to the main screen.
MANUAL CODING (opon #3)
Note: This method is mainly used to program sensor codes from
an old monitor to a new monitor if you do not have the sensors
available.
1. Push the “SET” buon unl it beeps. You are now in the
programming mode. The “HI PRESSURE SET” parameter
will blink at the boom of the screen. Push the (+) buon
and scroll through the parameters unl “SET ID” appears.
2. Quickly press and release the “SET” buon. The rst re
on the display will blink. If you want to program a dierent
re, press the (+) buon to move to the correct re. Push
the “SET” buon again and the rst digit of “FFF FFF” will
ash. Press the (+) buon to select the correct number
or leer. Press “GO” to move to the next posion. Press
the (+) buon to change to the correct number or leer.
Connue this procedure unl all six digits are changed.
3. Press “SET” once to save the new codes. You will hear a
beep and the code will stop ashing.
TST-Doc-507 WSD-M Manual-(C)
7
TST-Doc-507 WSD-M Manual-(C)
4. To stop the coding for any posion, Press “BACK” once.
“FFF FFF” will reappear. No sengs will be saved.
5. Press “BACK” twice to return to the main screen.
DISPLAY INSTALLATION
1. The provided sucon cup mount can be used on the
windshield, side window or directly on a smooth dash.
Snap the mount into the back tabs on the display to use.
2. Plug the power cord into the vehicle’s cigaree lighter/
power port and then into the side of the monitor to charge
the internal lithium baery. Charge display for four (4)
hours the rst me.
DISPLAY BUTTONS
•There are ve (5) programming buons on the display.
They are: “GO”, “SET”, “BACK” on the le side of the
display and (+) and (-) on the right side of the display.
•The power slide switch is located on the right side of the
monitor. Slide it up to turn on the display. Slide it down
to turn o the display.
Display Mount
GO
SET
BACK
8
NOTE: The side power switch will not turn o the monitor when
constant power is applied to the unit.
PARAMETER SETTINGS (Seng the sensor alarms)
NOTE: The factory default sengs are:
Pressure Unit: PSI Temperature units: °C
High Pressure: 175 lbs. High Temperature: 158°F (70°C )
Low Pressure: 100 Lbs.
NOTE: Be sure your monitor is ON and it is showing the main
screen.
PRESSURE PARAMETERS
To choose the Pressure Parameter, press the “SET” buon unl it
beeps. Press the (+) buon three (3) mes and “SET” will appear
at the boom of the screen and BAR/PSI will be blinking on the
screen. Press the “SET” buon again and then use the (+) buon
to select “PSI” (or “BAR”). Press “SET” again to select it. Press
“BACK” to go back to the Main Screen.
TEMPERATURE PARAMETERS
To set the Temperature Parameters (°F or °C), press the “SET”
buon unl it beeps. Press the (+) buon four (4) mes and “SET”
will appear at the boom of the screen and °F/°Cwill appear on
TST-Doc-507 WSD-M Manual-(C)
Inhaltsverzeichnis
